Gt Table 176d3n
This document was ed by and they confirmed that they have the permission to share it. If you are author or own the copyright of this book, please report to us by using this report form. Report r6l17
Overview 4q3b3c
& View Gt Table as PDF for free.
More details 26j3b
- Words: 9,176
- Pages: 62
GT STRUDL
®
GTTABLE Manual
Computer-Aided Structural Engineering Center School of Civil & Environmental Engineering Georgia Institute of Technology Atlanta Georgia 30332-0355 USA www.gtstrudl.gatech.edu
This page intentionally left blank.
Rev U
- ii -
NOTICES GTSTRUDL® Reference Manual, GTTABLE, Revision U is applicable to Version 30 of GTSTRUDL released April 2009 and subsequent versions. GTSTRUDL® computer program is proprietary to and a trade secret of the Georgia Tech Research Corporation, Atlanta, Georgia 30332. GTSTRUDL® is a ed service mark of the Georgia Tech Research Corporation, Atlanta, Georgia, U.S.A.
DISCLAIMER NEITHER GEORGIA TECH RESEARCH CORPORATION NOR GEORGIA INSTITUTE OF TECHNOLOGY MAKE ANY WARRANTY EXPRESSED OR IMPLIED AS TO THE DOCUMENTATION, FUNCTION, OR PERFORMANCE OF THE PROGRAM DESCRIBED HEREIN AND THE S OF THE PROGRAM ARE EXPECTED TO MAKE THE FINAL EVALUATION AS TO THE USEFULNESS OF THE PROGRAM IN THEIR OWN ENVIRONMENT. Commercial Software Rights Legend Any use, duplication, or disclosure of this software by or for the U.S. Government shall be restricted to the of a license agreement in accordance with the clause at DFARS 227.7202-3 (June 2005). This material may be reproduced by or for the U.S. Government pursuant to the copyright license under the clause at DFARS 252-227-7013, September 1989. Georgia Tech Research Corporation Georgia Institute of Technology Atlanta, Georgia 30332-0355 Copyright © 2009 Georgia Tech Research Corporation Atlanta, Georgia 30332 ALL RIGHTS RESERVED Printed in United States of America - iii -
Rev U
This page intentionally left blank.
Rev U
- iv -
GTSTRUDL Manual Revision History Revision No.
Date Released
U
4/2009
Description GTSTRUDL Reference Manual, GTTABLE, has been updated and is applicable to Version 30 of GTSTRUDL and subsequent versions. .
-v-
Rev U
This page intentionally left blank.
Rev U
- vi -
Table of Contents Section
Page
NOTICES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii DISCLAIMER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii GTSTRUDL Reference Manual Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii List of Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii List of Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii
1.0 1.1 1.2
GTTABLE Subsystem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 GTTABLE Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.0
INITIATE Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3.1 3.2
ADD HEADINGS Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 ADD ITEMS Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.1 4.2
MODIFY Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 MODIFY ITEMS Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.1 5.2 5.3
ORDER Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 ORDER BY Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 ARRANGE Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
6.1 6.2
TRANSFER Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 TRANSFER ITEMS Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
7.1 7.2 7.3
DELETE Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 DELETE HEADINGS Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 DELETE ITEMS Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
8.1 8.2 8.3 8.4 8.5
OUTPUT Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 PRINT HEADINGS Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 PRINT ITEMS Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 PRINT ITEM NAMES Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 PRINT ORDERINGS Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 - vii -
Rev U
Section
Page
9.0
UNITS Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
10.0
LIST Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
11.0
CHANGE Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
12.1 12.2 12.3 12.4 12.5 12.6 12.7
EXAMPLE 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 EXAMPLE 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 EXAMPLE 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 EXAMPLE 4.1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 EXAMPLE 4.2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 EXAMPLE 5.1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 EXAMPLE 5.2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
List of Figures Figure 1.1-1 Figure 1.1-2
GTSTRUDL Table Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 GTSTRUDL Table ‘EXSTEEL’, Example 4.1 AND 4.2 . . . . . . . . . . . . . . . . . 2
List of Tables Table 12.2-1 Table 12.3-1
Rev U
GTSTRUDL Table Properties for Analysis . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 GTSTRUDL Table Properties for Analysis and Steel Design . . . . . . . . . . . . 37
- viii -
GTTABLE
1.0
GTTABLE Subsystem
1.1
Introduction
GTTABLE Commands
GTTABLE is a subsystem which provides the with a convenient language for storing and retrieving tabular data. These data are then available for use by other subsystems, GTSTRUDL for example. Originally implemented as a stand-alone subsystem, GTTABLE, is now an integrated part of GTSTRUDL. The purpose of this Manual is to familiarize the with how to create and modify tables. Tables created by GTTABLE are structured as shown in Figures 1.1-1 and 1.1-2. These tables are two-dimensional arrays with an arbitrary number of columns and rows containing data. Each row represents a unique item within a given table, while each column represents a unique heading for data in the table. The names of items and headings may be up to eight characters long. GTTABLE provides for two data sets in which tables may be stored; one a data set, and the second a subsystem (GTSTRUDL) data set. Both data sets allow the to protect data in a table by specifying a unique for each table. Data in any table are always available for output, even when the table is protected. Besides the simple inputting and outputting of the tabular data, the information within the table also can be ordered. The items in a table can be ordered by increasing or decreasing value of a particular heading. Such orderings may then be used to arrange other headings in the table. The orderings and arrangements created by GTTABLE may be used by other subsystems to aid searches through a particular table. As the commands of GTTABLE are described, the examples presented will construct the table in Figure 1.1-2. This table will be referred to by the name ‘EXSTEEL’, and it will be placed in the data set. At the conclusion of this report the complete sequence of commands will be presented.
-1-
Rev U
GTTABLE Commands
GTTABLE
TABLE HEADING NAMES Table Item Names
Figure 1.1-1
WEIGHT (lb/ft)
AX (in2)
Heading values stored by item
General Table Format
DEPTH (in)
IZ (in4)
IY (in4)
SZ (in3)
‘W14X90'
90.0
26.5
14.02
999.0.
362.0
143.0
‘W12X58'
58.0
17.0
12.19
475.0
107.0
78.0
‘W4X13'
13.0
3.83
4.16
11.3
3.86
5.46
‘W10X100'
100.0
29.4
11.1
623.0
207.0
112.0
‘W16X50'
50.0
14.7
16.26
659.0
37.2
81.0
‘C5X9'
9.0
2.64
5.0
8.9
0.632
3.56
Figure 1.1-2
Rev U
Example Table ‘EXSTEEL’, Example 4.1 and 4.2
-2-
GTTABLE
1.2
GTTABLE Commands
GTTABLE Commands
GTTABLE commands are organized into table operation blocks. Each operation block performs one of the following functions: INITIATE MODIFY DELETE OUTPUT ORDER TRANSFER Each table operation block must begin with an operation heading command. Specific operation commands may be given only after the appropriate operation heading command is given. All Table operation blocks, except OUTPUT, must be closed with a ‘FILE TABLE’ command. In the discussion that follows the GTTABLE commands are presented in operation blocks. An operation heading command is described, then the specific operation commands appropriate for that block are described. Before any specific command or operation heading commands can be processed, the TABLE command must be given. This is accomplished with the following command: TABLE (‘title’)
Elements: ‘title’ = an optional 64-character description of the TABLE job which follows. After TABLE command is given, the GTTABLE commands described in the remainder of this document can be given.
-3-
Rev U
GTTABLE Commands
GTTABLE
This page intentionally left blank.
Rev U
-4-
GTTABLE
2.0
INITIATE Command
INITIATE Command
( ) Indicates optional keywords. { } Indicates a choice of keywords.
name
= The name of the table that is being created, which cannot be more than 8 characters and is required.
= Optional for the particular table being created. If a is given here, it must be given on all other commands specifying a . This command is used to create a new table. The table may be created under the data set. A may be attached with the particular table if so desired. Once a new table has been initiated with this command, the following commands may be used with this operation block: ADD HEADING ADD ITEMS MODIFY ITEMS
EXAMPLE: INITIATE TABLE <EXSTEEL’ or INI ‘EXSTEEL’
The above examples all create the same table ‘EXSTEEL’ in the data set without a .
-5-
Rev U
INITIATE Command
GTTABLE
This page intentionally left blank.
Rev U
-6-
GTTABLE
3.1
ADD HEADINGS Command
ADD HEADINGS Command ADD HEADINGS ‘nameh1’ dimension (n) ‘nameh2’ dimension (n) C C C C C C namehi
=
... ... C C C Name of the heading to be added to the table with no more than 8 characters. No duplication of names may exist within a table.
*
This command may be used in either the INITIATE or MODIFY an operation block. This command allows the creation of new headings in the table. The ADD HEADINGS command is followed by the name of the heading and the associated dimensions. The value of n corresponds to the exponent of the dimension, assume 1 if not given.
EXAMPLE: ADD HEADINGS <WEIGHT’ WEIGHT 1 LENGTH –1
-7-
Rev U
ADD ITEMS Command
3.2
GTTABLE
ADD ITEMS Command ADD ITEMS ‘names1’ ‘names2’ C C C
(
‘nameh1’ v11 v21 C C C
namehi
=
Name of the heading under which information for the item is input. These names may be omitted in which case the values entered will correspond to the headings as they were created.
namesi
=
Name of the item being added, which is up to 8 characters in length. No duplication of names may exist.
vim
=
‘nameh2’ v12 v22 C C C
‘nameh2' v13 v23 C C C
... ) ... ... C C C
Data value for item i and heading m.
This command can be used in the INITIATE and MODIFY operation blocks. It is used to add new items to the table.
EXAMPLE: UNITS INCH POUND ADD ITEMS ‘WEIGHT’ ‘W14X90’ 7.5 ‘W12X58’ 4.8333 ‘W4X13’ 1.0833 ‘W10X100’ 8.3333 ‘W16X50’ 4.1667 ‘C5X9’ 0.75 FILE TABLE
‘AX’ 26.5 17.0 3.83 29.4 14.75 2.64
‘YD’ 14.02 12.19 4.16 11.1 16.26 5.0
‘IZ’ 990.0 475.0 11.3 623.0 659.0 8.9
‘IY’ 362.0 107.0 3.86 207.0 37.2 0.632
‘SZ’ 143.0 78.0 5.46 112.0 81.0 3.56
Note that the value of AX for the item W16X50 intentionally is specified as 14.75 so we can show how to use the MODIFY ITEMS option to change it to 14.7.
Rev U
-8-
GTTABLE
4.1
MODIFY Command
MODIFY Command
name = Name of the existing table that is to be modified. { }
Indicates a choice of keywords.
( )
Indicates an optional keyword.
This operation heading command is used to CHANGE or ADD information in an existing table. If a was used when the table was created, it must be included here also. Once the has specified the MODIFY statement, the following commands may be used: ADD HEADINGS ADD ITEMS MODIFY ITEMS
EXAMPLE: MODIFY TABLE
‘WSHAPES’
‘MYWD’
-9-
Rev U
MODIFY ITEMS Command
4.2
GTTABLE
MODIFY ITEMS Command MODIFY ITEMS
( ‘nameh1’ ‘nameh2’ ... )
‘names1’
v11
v12
...
‘names2’
v21
v22
...
namehi
=
Name of an existing heading within the table that is to be modified. If the heading names are omitted, the new values for each item will be assigned in the same order as they were given in the ADD HEADINGS command.
namesi
=
Name of an existing item within the table that is to be modified.
vim
=
The new value for the item i and heading m.
This command can be used with the operation heading command MODIFY. The operation heading command (MODIFY) must appear before the MODIFY ITEMS command.
EXAMPLE: MODIFY TABLE ‘EXSTEEL’ MODIFY ITEMS ‘AX’ ‘W16X50’ 14.7 FILE TABLE
This example replaces the old value of AX for section ‘W16X50’ with the new value of 14.70.
Rev U
- 10 -
GTTABLE
5.1
ORDER Command
ORDER Command
name
=
Name of the existing table that is to be ordered.
=
The current for the table specified.
This operation heading command is used to order a heading within a table. An ordering may also be arranged according to another heading. The allowable commands in this operation block are: ORDER BY ARRANGE
If the keywords ‘FOR STRUDL’ are included, table will automatically produce the orderings used by GTSTRUDL. When this is done, no other commands should be used in the ORDER operation block. FILE TABLE should always end this operation block.
EXAMPLE: ORDER TABLE ‘EXSTEEL’ ORDER BY INCREASING ‘AX’ ARRANGE ‘SZ’ ON ORDERING ‘AX’ WITH ID ‘AXSZ’ FILE TABLE
- 11 -
Rev U
ORDER BY Command
5.2
GTTABLE
ORDER BY Command
namehi
=
Name of a heading within the table that is to be ordered.
This command is used with the ORDER operation heading command. This command is used to specify what heading is to be ordered and in what direction the ordering is to proceed. This command should be followed by FILE TABLE.
EXAMPLE: ORDER TABLE ‘EXSTEEL’ ORDER BY INCREASING ‘AX’ ARRANGE ‘SZ’ ON ORDERING ‘AX’ WITH ID ‘AXSZ’ FILE TABLE
Rev U
- 12 -
GTTABLE
5.3
ARRANGE Command
ARRANGE Command ARRANGE ‘name2’ (ON) (ORDERING) ‘name1’ (WITH) (ID) ‘id’
name2
=
Name of the heading that is to be arranged according to ordering name1.
name1
=
Name of an existing ordering.
id
=
Name for the arrangement different from name1 and name2.
This command is used within the ORDER operation block. It arranges the specified heading in the same sequence as a specified ordering. The ordering should already exist.
EXAMPLE: ORDER TABLE ‘EXSTEEL’ ORDER BY INCREASING ‘AX’ ARRANGE ‘SZ’ ON ORDERING ‘AX’ WITH ID ‘AXSZ’ FILE TABLE
- 13 -
Rev U
ARRANGE Command
GTTABLE
This page intentionally left blank.
Rev U
- 14 -
GTTABLE
6.1
TRANSFER Command
TRANSFER Command
name1
=
Name of the existing table where the data is located.
name2
=
Name of the table where the data is to be placed, it may be a new or existing table.
=
for the second table, which must agree if the table has been already created.
ALL
Optional, but if used all of the data will be transferred. Orderings cannot be transferred.
=
{ } Indicates a choice between keywords. ( )
Indicates an optional keyword.
This operation heading command is used to transfer all or part of an existing table to another table that already exists or to a new table. Allowable operations within this operation heading block are: TRANSFER ITEMS
- 15 -
Rev U
TRANSFER ITEMS Command
6.2
GTTABLE
TRANSFER ITEMS Command
itemi
=
Item to be transferred to the other table.
n1
=
Position of the first item to be transferred.
n2
=
Position of the last item to be transferred.
This command may only be used within the TRANSFER heading block. This command is used to transfer only a portion of an existing table to another table.
Rev U
- 16 -
GTTABLE
7.1
DELETE Command
DELETE Command
{ }
Indicates a choice between keywords.
(
Indicates an optional keyword.
)
This operation heading command is used to delete all or part of an existing table. If a was used when the table was created, then the must be specified here. The other commands allowed within this operation heading block are: DELETE ITEMS DELETE HEADINGS If ‘ALL’ is specified, the entire table is deleted and no other commands are necessary. If ‘ALL’ is not specified, then one of the allowable commands below (DELETE HEADINGS or DELETE ITEMS) is expected to follow this command.
- 17 -
Rev U
DELETE HEADINGS and DELETE ITEMS Command
7.2
GTTABLE
DELETE HEADINGS Command DELETE HEADINGS ‘nameh1’ ‘nameh2’ ...
namehi
=
Name of the existing heading that is to be deleted in the table. The deletion removes all values under that heading and also removes all orderings within the table.
This command must be preceded by the DELETE operation heading command.
7.3
DELETE ITEMS Command DELETE ITEMS ‘names1’ ‘names2’ ...
namesi
=
Name of the existing item in the table that is to be deleted. The deletion also removes all orderings in that table.
This command must be preceded by the DELETE operation heading command.
Rev U
- 18 -
GTTABLE
8.1
OUTPUT Command
OUTPUT Command
name
=
Name of the table to be output.
FORMAT F
=
The output is in decimal point form with 6 digits to the right of the decimal.
FORMAT E
=
This output is in exponential form.
ALL
=
If given in this command, the entire table is output including orderings and arrangements. If ‘ALL’ is not given, then the allowable PRINT commands are expected to follow.
This operation heading command is used to output the table information. A is not needed to obtain the information. The allowable commands within this operation heading command are: PRINT HEADINGS PRINT ITEMS PRINT ITEM NAMES PRINT ORDERINGS
- 19 -
Rev U
PRINT HEADINGS and PRINT ITEMS Command
8.2
GTTABLE
PRINT HEADINGS Command PRINT HEADINGS ‘nameh1’ ‘name2’ ...
namehi
=
Name of the heading to be output. If no names are given, then all of the headings will be output.
This command is contained in the OUTPUT operation heading command. This command initializes what headings are to be output for the given items to follow in the PRINT ITEMS command.
8.3
PRINT ITEMS Command
itemi = Name of the item to be output. n1
= Position of first item to be output.
n2
= Position of second item to be output.
This command is contained in the OUTPUT operation heading command. This command specifies which items are to be output.
Rev U
- 20 -
GTTABLE
8.4
PRINT ITEM NAMES, PRINT ORDERINGS
PRINT ITEM NAMES Command PRINT ITEM NAMES
This command is used within the OUTPUT operation heading command. It is used to obtain a listing of the item names within the table, but not the associated data values.
8.5
PRINT ORDERINGS Command PRINT ORDERINGS
nameoi
=
‘nameo1’
‘nameo2’ ...
Name of the ordering to be output.
This command is contained within the OUTPUT operation heading command. This command outputs the orderings listed for the table.
- 21 -
Rev U
PRINT ITEM NAMES and PRINT ORDERINGS Command
This page intentionally left blank.
Rev U
- 22 -
GTTABLE
GTTABLE
9.0
UNITS Command
UNITS Command *
{ } Indicates a choice of keywords. * Indicates more than one choice can be made. This command may be used between operation blocks to specify a new set of units. Initially the units are automatically set to inches, pounds, radians, second, and Fahrenheit. There are five areas of units which are: length, force, angle, time, temperature. One or more of the units may be specified at any time.
EXAMPLE: UNITS MM KN DEGREE
- 23 -
Rev U
UNITS Command
GTTABLE
This page intentionally left blank.
Rev U
- 24 -
GTTABLE
LIST Command
10.0 LIST Command Output Tables in the data set (DAT.DS). FLIST 1 Output Tables in the SUBSYSTEM data set (GTSTRUDL Table database). FLIST 2
This operation may be used between operation blocks to find out what tables are contained on each data set.
- 25 -
Rev U
CHANGE Command
GTTABLE
This page intentionally left blank.
Rev U
- 26 -
GTTABLE
LIST Command
11.0 CHANGE Command
name = Name of the table for which the is to be changed.
This command allows the to change the for a table. The command should be used between operation heading blocks. If the old is non-existent, then the ‘FROM OLDPSWD’ can be omitted.
- 27 -
Rev U
CHANGE Command
GTTABLE
This page intentionally left blank.
Rev U
- 28 -
GTTABLE
EXAMPLE 1
12.1 EXAMPLE 1: Building a Table from an Existing table GTTABLE can be used to build special subsets of the subsystem tables provided with GTSTRUDL. s of the Member Selection capabilities of GTSTRUDL should consider building special tables, since they can increase the efficiency of the selection process. The following example shows how a table of W14 shapes is built from the GTSTRUDL table WSHAPES9. In addition, several W14s are deleted from the resulting table. TABLE ‘Building Special Tables’ $ TRANSFER SUBSYSTEM TABLE ‘WSHAPES9’ TO TABLE ‘W14’ TRANSFER ITEMS FROM ‘W14X730’ TO ‘W14X22’ FILE TABLE $ DELETE TABLE ‘W14’ DELETE ITEMS ‘W14X605’ ‘W14X455’ ‘W14X283’ ‘W14X211’ FILE TABLE $ ORDER TABLE ‘W14’ ORDER BY INCREASING ‘AX’ ARRANGE ‘SY’ ON ORDERING ‘AX’ WITH ID ‘AXSY’ ARRANGE ‘SZ’ ON ORDERING ‘AX’ WITH ID ‘AXSZ’ FILE TABLE $ OUTPUT TABLE ‘W14’ ALL $ FINISH The above example creates a special table of W14 shapes, which is to be permanently stored on the data set (DAT.DS).
- 29 -
Rev U
EXAMPLE 2
GTTABLE
12.2 EXAMPLE 2: Building a New Table s of GTSTRUDL may find it convenient to build their own tables of frequently used member properties. The following example illustrates how such a table can be built. The table WELDPG supplies only those properties required by GTSTRUDL for analysis, as described in Table 12.2-1. If the table is to be used for member selection or checking, additional properties must be included in the table (see Example 3 of Section 12.3 for ISHAPES and Table 12.3-1 for properties description). The specific properties to be added for member selection depend on the cross-sectional shape of the profile, and the GTSTRUDL design code being used. The is referred to Volume 2A, Section ASD9, TOWER2, etc. for a description of additional properties required for member selection. Properties are given after the profile name in the same order as given in the ADD HEADINGS command. s must the accuracy of all tables they build, as no internal checks are made in GTSTRUDL of data taken from tables. Properties which are not included in a particular table are taken as zero by GTSTRUDL.
Rev U
- 30 -
GTTABLE
EXAMPLE 2
TABLE 'Building a New Table' $ $ This Table has the required properties for ANALYSIS only. $ INITIATE TABLE 'WELDPG' $ ADD HEADINGS 'AX' LENGTH 2 'AY' LENGTH 2 'AZ' LENGTH 2 'IX' LENGTH 4 'IY' LENGTH 4 'IZ' LENGTH 4 'YD' LENGTH 1 'YC' LENGTH 1 'ZD' LENGTH 1 'ZC' LENGTH 1 'SY' LENGTH 3 'SZ' LENGTH 3 'EY' LENGTH 1 'EZ' LENGTH 1 $ ADD ITEMS $ 'PG92X823' 241.8750 61.8750 120.0000 549.7485 431105.6250 96.0000 48.0000 30.0000 900.1625 8981.3672 0.0000 0.0000 $ 'PG92X517' 151.8750 61.8750 60.0000 77.2485 230158.1250 93.0000 46.5000 30.0000 450.1625 4949.6372 0.0000 0.0000 $ 'PG86X654' 192.5000 52.5000 93.3333 298.5026 292821.6875 89.0000 44.5000 28.0000 653.4554 6580.2627 0.0000 0.0000
- 31 -
13502.4375 15.0000 -
6752.4370 15.0000 -
9148.3760 14.0000 -
Rev U
EXAMPLE 2 $ 'PG86X464'
$ 'PG74X423'
$ 'PG74X301'
$ 'PG49X197'
$ 'PG45X128'
$ 'PG36X300'
GTTABLE 136.5000 184401.0000 392.1221
52.5000 87.0000 4239.1035
56.0000 43.5000 0.0000
69.8359 28.0000 0.0000
5489.7090 14.0000 -
124.6125 132504.2813 336.0892
40.6125 75.7000 3500.7737
56.0000 37.8500 0.0000
90.0333 24.0000 0.0000
4033.0708 12.0000 -
88.5000 81448.0000 192.0890
40.5000 74.0000 2201.2974
32.0000 37.0000 0.0000
20.2715 24.0000 0.0000
2305.0679 12.0000 -
58.0000 27716.8340 106.6930
18.0000 50.5000 1097.6964
26.6667 25.2500 0.0000
21.6771 16.0000 0.0000
853.5443 8.0000 -
37.7500 14234.8330 64.0140
13.7500 45.5000 625.7070
16.0000 22.7500 0.0000
4.9476 16.0000 0.0000
512.1119 8.0000 -
87.5049 20138.9023 155.6197
31.5441 36.7400 1096.2930
37.3072 18.3700 0.0000
62.0378 16.6550 0.0000
1295.9235 8.3275 -
$ FILE TABLE $ $ OUTPUT TABLE 'WELDPG' ALL $ FINISH
Rev U
- 32 -
GTTABLE
EXAMPLE 2 Table 12.2-1
GTSTRUDL Table Properties for Analysis Property
Description
AX
Cross-section area
AY
Y-axis shear area
AZ
Z-axis shear area
IX
Torsion constant
IY
Y-axis moment of inertia
IZ
Z-axis moment of inertia
YD
Depth parallel to Y-axis
YC
Distance from centroid to extreme fiber in positive Y direction
ZD
Depth parallel to Z-axis
ZC
Distance from centroid to extreme fiber in positive Z direction
SY
Y-axis section modulus
SZ
Z-axis section modulus
EY
Distance from centroid to shear center parallel to the Y-axis
EZ
Distance from centroid to shear center parallel to the Z-axis
- 33 -
Rev U
EXAMPLE 3
GTTABLE
12.3 EXAMPLE 3: Building a New Table for Analysis and Design TABLE 'Building a New Table for Analysis and Design' $ INITIATE TABLE 'ISHAPES' $ $ ADD HEADINGS 'ND' LENGTH 1 'WEIGHT' WEIGHT 1 LENGTH -1 'AX' LENGTH 2 'AY' LENGTH 2 'AZ' LENGTH 2 'YD' LENGTH 1 'WBTK' LENGTH 1 'ZD' LENGTH 1 'FLTK' LENGTH 1 'BF/2TF' 'D/TW' 'RT' LENGTH 1 'YD/AFL' LENGTH -1 'IZ' LENGTH 4 'SZ' LENGTH 3 'SZS' LENGTH 3 'RZ' LENGTH 1 'IY' LENGTH 4 'SY' LENGTH 3 'SYS' LENGTH 3 'RY' LENGTH 1 'ZZ' LENGTH 3 'ZY' LENGTH 3 'IX' LENGTH 4 'CW' LENGTH 6 'INTYD' LENGTH 1 'YC' LENGTH 1 'ZC' LENGTH 1 'EY' LENGTH 1 'EZ' LENGTH 1
Rev U
- 34 -
GTTABLE
EXAMPLE 3
'GRPNUM' 'SHAPE' $ $ ADD ITEMS $ $ 'W16X50'
'W14X48'
'W12X45'
'S8X23'
16.000 16.260 42.800 81.000 1.590 15.000 1.000 14.000 13.790 40.600 70.300 1.910 12.600 1.000 12.000 12.060 36.000 58.100 1.940 10.910 1.000 8.000 8.000 18.100 16.200 0.798 7.148 1.000
4.167 0.380 1.840 6.680 92.000 8.130 1.000 4.000 0.340 2.130 5.850 78.400 6.895 1.000 3.750 0.335 2.150 5.150 64.700 6.030 1.000 1.917 0.441 0.950 3.100 0.550 4.000 1.100
- 35 -
14.700 7.070 3.650 37.200 16.300 3.535
6.179 0.630 659.000 10.500 1.520 0.000
5.939 5.600 81.000 10.500 2270.000 0.000
-
14.100 8.030 2.890 51.400 19.600 4.015
4.689 0.595 485.000 12.800 1.460 0.000
6.370 6.700 70.300 12.800 2240.000 0.000
-
13.200 8.045 2.610 50.000 19.000 4.022
4.040 0.575 350.000 12.400 1.310 0.000
6.168 7.000 58.100 12.400 1650.000 0.000
-
6.770 4.171 4.510 4.310 19.300 2.086
3.528 0.426 64.900 2.070 3.680 0.000
2.369 4.900 16.200 2.070 61.800 0.000
-
Rev U
EXAMPLE 3 'HP8X36'
'M10X9'
GTTABLE 8.000 8.020 18.000 29.800 1.950 7.130 2.000 10.000 10.000 63.700 7.760 0.480 9.588 1.000
3.000 0.445 2.180 3.360 0.770 4.010 1.200 0.750 0.157 0.610 3.830 0.030 5.000 1.300
10.600 8.155 2.210 40.300 33.600 4.078
3.569 0.445 119.000 9.880 15.200 0.000
4.839 9.200 29.800 9.880 578.000 0.000
-
2.650 2.690 18.000 0.609 9.190 1.345
1.570 0.206 38.800 0.453 0.765 0.000
0.739 6.500 7.760 0.453 14.600 0.000
-
FILE TABLE $ $ $ Following ORDER command is required for SELECT command. $ ORDER TABLE 'ISHAPES' FOR STRUDL FILE TABLE $ OUTPUT TABLE 'ISHAPES' FORMAT F ALL $ $ FINISH
Rev U
- 36 -
GTTABLE
EXAMPLE 3 Table 12.3-1
GTSTRUDL Table Properties for Analysis and Steel Design Property
Description
AX
cross-section area
AY
Y axis shear area computed as the profile depth times the web thickness
AZ
Z axis shear area computed as 2/3 of the total flange area
IX
torsional moment of inertia
IY
moment of inertia about the Y axis
IZ
moment of inertia about the Z axis
RY
radius of gyration about the Y axis
RZ
radius of gyration about the Z axis
RT
radius of gyration for the flange and 1/3 of the compression web area about an axis in the plane of the web; for these shapes 1/3 of the compression web area is 1/6 of the total web area
ZY
plastic modulus about the local Y axis
ZZ
plastic modulus about the local Z axis
SY
section modulus about the Y axis
SYS
SY
SZ
section modulus about the Z axis
SZS
SZ
FLTK
flange thickness
WBTK
web thickness
YD
profile depth
YC
positive Y direction distance from the Z axis to the extreme fiber along the Y axis
ZD
flange width
ZC
the positive Z direction distance from the Y axis to the extreme fiber along the Z axis
- 37 -
Rev U
EXAMPLE 3
GTTABLE Table 12.3-1 (continued) GTSTRUDL Table Properties for Analysis and Steel Design
Property
Description
INTYD
clear depth of the web computed as the profile depth minus twice the flange thickness
BF/2TF
b/t ratio of the flange computed as ½ the flange width divided by the flange thickness
D/TW
profile depth divided by the web thickness
YD/AFL
profile depth divided by the area of one flange
EY
distance from centroid to shear center parallel to the Y axis
EZ
distance from centroid to shear center parallel to the Z axis
CW
warping constant
ND
nominal depth
WEIGHT
profile group number taken from Table 1 and 2 of the AISC ASD Manual of Steel Construction Ninth Edition
GRPNUM
profile group number taken from Table 1 and 2 of the AISC ASD Manual of Steel Construction Ninth Edition
SHAPE
a number indicating the profile shape = 1.0, W shapes = 1.1, S shapes = 1.2, HP shapes = 1.3, M shapes
Rev U
- 38 -
GTTABLE
EXAMPLE 4.1
12.4 EXAMPLE 4.1: General example to show Modify, Transfer, Change , and Delete Command (Input file only). TABLE ‘EXAMPLE’ INITIATE TABLE ‘EXSTEEL’ ADD HEADINGS ‘WEIGHT’ WEIGHT 1 LENGTH -1 ‘AX’ LENGTH 2 ‘YD’ L 1 $ DEPTH ‘IZ’ L 4 ‘IY’ L 4 ‘SZ’ L 3 UNITS INCH POUND $ ADD ITEMS ‘WEIGHT’ ‘AX’ ‘YD’ ‘IZ’ ‘IY’ ‘SZ’ ‘W14X90' 7.9167 26.5 14.02 999.0. 362.0 143.0 ‘W12X58' 4.8333 17.0 12.19 475.0 107.0 78.0 ‘W4X13' 1.0833 3.83 4.16 11.3 3.86 5.46 ‘W10X100' 8.3333 29.4 11.1 623.0 207.0 112.0 ‘W16X50' 4.1667 14.75 16.26 659.0 37.2 81.0 ‘C5X9' 0.75 2.64 5.0 8.9 0.632 3.56 FILE TABLE $ $ CHANGE THE VALUE OF AX FOR SECTION ‘W16X50’ $ WITH A NEW VALUE OF 14.70. $ MODIFY TABLE ‘EXSTEEL’ MODIFY ITEMS ‘AX’ ‘W16X50' 14.7 FILE TABLE OUTPUT TABLE ‘EXSTEEL’ ALL ORDER TABLE ‘EXSTEEL’ ORDER BY INCREASING ‘AX’ ORDER TABLE ‘EXSTEEL’ ARRANGE ‘SZ’ ON ORDERING ‘AX’ WITH ID ‘AXSZ’ FILE TABLE OUTPUT ‘EXSTEEL’ ALL TRANSFER TABLE <EXSTEEL’ TO
Rev U
EXAMPLE 4.1
GTTABLE
OUTPUT TABLE
Rev U
- 40 -
GTTABLE
EXAMPLE 4.2
12.5 EXAMPLE 4.2: INPUT and OUTPUT of EXAMPLE 4.1 TABLE ‘EXAMPLE’ INITIATE TABLE ‘EXSTEEL’ ADD HEADINGS ‘WEIGHT’ WEIGHT 1 LENGTH -1 ‘AX’ LENGTH 2 ‘YD’ L 1 $ DEPTH ‘IZ’ L 4 ‘IY’ L 4 ‘SZ’ L 3 UNITS INCH POUND ADD ITEMS ‘WEIGHT’ ‘AX’
‘YD’
‘IZ’
‘W14X90' 7.9167 26.5 14.02 999.0 ‘W12X58' 4.8333 17.0 12.19 475.0 ‘W4X13' 1.0833 3.83 4.16 11.3 ‘W10X100' 8.3333 29.4 11.1 623.0 ‘W16X50' 4.1667 14.75 16.26 659.0 ‘C5X9' 0.75 2.64 5.0 8.9 FILE TABLE $ $ CHANGE THE VALUE OF AX FOR SECTION ‘W16X50’ $ WITH A NEW VALUE OF 14.70. $ MODIFY TABLE ‘EXSTEEL’ MODIFY ITEMS ‘AX’ ‘W16X50' 14.7 FILE TABLE OUTPUT TABLE ‘EXSTEEL’ ALL
- 41 -
‘IY’ 362.0 107.0 3.86 207.0 37.2 0.632
‘SZ’ 143.0 78.0 5.46 112.0 81.0 3.56
Rev U
EXAMPLE 4.2
GTTABLE
***************************** * TABLE OUTPUT EXSTEEL * ***************************** HEADINGS WEIGHT AX YD IZ IY SZ
LB INCH INCH INCH INCH INCH
1 2 1 4 4 3
INCH
-1
TABLE DATA WEIGHT W14X90 7.916700 W12X58 4.833300 W4X13 1.083300 W10X100 8.333300 W16X50 4.166700 C5X9 0.750000
AX 26.500000 17.000000 3.820000 29.400000 14.750000 2.640000
DEPTH 14.020000 12.190000 4.160000 11.100000 16.250000 5.000000
IZ IY SZ 999.000000 362.000000 143.000000 475.000000 107.000000 78.000000 11.300000 3.860000 5.460000 623.000000 207.000000 112.000000 659.000000 37.020000 81.000000 8.900000 0.632000 3.560000
ORDER TABLE ‘EXSTEEL’ ORDER BY INCREASING ‘AX’ ORDER TABLE ‘EXSTEEL’ ARRANGE ‘SZ’ ON ORDERING ‘AX’ WITH ID ‘AXSZ’ FILE TABLE OUTPUT ‘EXSTEEL’ ALL ***************************** * TABLE OUTPUT EXSTEEL * ***************************** HEADINGS WEIGHT AX YD IZ IY SZ
Rev U
LB INCH INCH INCH INCH INCH
1 2 1 4 4 3
INCH
-1
- 42 -
GTTABLE
EXAMPLE 4.2
TABLE DATA WEIGHT 7.916700 4.833300 1.083300 8.333300 4.166700 0.750000
W14X90 W12X58 W4X13 W10X100 W16X50 C5X9
AX 26.500000 17.000000 3.820000 29.400000 14.700000 2.640000
DEPTH 14.020000 12.190000 4.160000 11.100000 16.250000 5.000000
IZ IY SZ 999.000000 362.000000 143.000000 475.000000 107.000000 78.000000 11.300000 3.860000 5.460000 623.000000 207.000000 112.000000 659.000000 37.020000 81.000000 8.900000 0.632000 3.560000
ORDERING ITEMS C5X9 W4X13 W16X50 W12X58 W14X90 W10X100
AX
--INCH 2
2.6400001 3.8300000 14.700000 17.000000 26.500000 29.400000
AXSZ
= SZ ARRANGED ON ORDERING AX
ITEMS
AXSZ
C5X9 W4X13 W16X50 W12X58 W14X90 W10X100
--INCH 4
3.560000 5.460000 81.000000 78.000000 143.000000 112.000000
TRANSFER TABLE ‘EXSTEEL’ TO ‘TRIAL’ ‘NEW’ ALL FILE TABLE OUTPUT TABLE ‘TRIAL’ ALL
- 43 -
Rev U
EXAMPLE 4.2
GTTABLE
***************************** * TABLE OUTPUT TRIAL * ***************************** HEADINGS WEIGHT AX YD IZ IY SZ
LB INCH INCH INCH INCH INCH
1 2 1 4 4 3
INCH
-1
TABLE DATA
W14X90 W12X58 W4X13 W10X100 W16X50 C5X9
WEIGHT 7.916700 4.833300 1.083300 8.333300 4.166700 0.750000
AX 26.500000 17.000000 3.820000 29.400000 14.700000 2.640000
DEPTH 14.020000 12.190000 4.160000 11.100000 16.250000 5.000000
IZ IY SZ 999.000000 362.000000 143.000000 475.000000 107.000000 78.000000 11.300000 3.860000 5.460000 623.000000 207.000000 112.000000 659.000000 37.020000 81.000000 8.900000 0.632000 3.560000
CHANGE FOR TABLE ‘TRIAL’ FROM ‘NEW’ TO ‘OLD’ THE FOR TABLE TRIAL HAS BEEN CHANGED DELETE TABLE ‘TRIAL’ ‘OLD’ DELETE ITEM ‘C5X9' FILE TABLE **** FOLLOWING MESSAGE REFERS TO PREVIOUS OPERATION BLOCK **** TABLE MESSAGE 3.2 - TABLE DELETION SUMMARY **** FOLLOWING ITEMS ARE DELETED C5X9
Rev U
- 44 -
GTTABLE
EXAMPLE 4.2
OUTPUT TABLE ‘TRIAL’ ALL ***************************** * TABLE OUTPUT TRIAL * ***************************** HEADINGS WEIGHT AX YD IZ IY SZ
LB INCH INCH INCH INCH INCH
1 2 1 4 4 3
INCH
-1
TABLE DATA
W14X90 W12X58 W4X13 W10X100 W16X50
WEIGHT 7.916700 4.833300 1.083300 8.333300 4.166700
AX 26.500000 17.000000 3.820000 29.400000 14.700000
DEPTH 14.020000 12.190000 4.160000 11.100000 16.250000
IZ IY SZ 999.000000 362.000000 143.000000 475.000000 107.000000 78.000000 11.300000 3.860000 5.460000 623.000000 207.000000 112.000000 659.000000 37.020000 81.000000
DELETE TABLE ‘EXSTEEL’ ALL DELETE TABLE ‘TRIAL’ ‘OLD’ ALL **** FOLLOWING MESSAGE REFERS TO PREVIOUS OPERATION BLOCK **** TABLE MESSAGE 3.1 - TABLE EXSTEEL IS DELETED FINISH
- 45 -
Rev U
EXAMPLE 5.1
GTTABLE
12.6 EXAMPLE 5.1: Transfer from GTSTRUDL Table to Table Example (INPUT file only) TABLE TRANSFER SUBSYSTEM TABLE ‘EXSTEEL’ TO TABLE ‘WSECT’ TRANSFER ITEMS FROM ‘W14X730’ TO ‘W14X22’ FILE TABLE DELETE TABLE ‘WSECT’ DELETE ITEMS ‘W14X605' ‘W14X455' ‘W14X287' ‘W14X219' FILE TABLE OUTPUT TABLE ‘WSECT’ PRINT ITEM NAMES OUTPUT TABLE ‘WSECT’ ALL FINISH
Rev U
- 46 -
GTTABLE
Example 5.2
12.7 EXAMPLE 5.2: INPUT and OUTPUT of EXAMPLE 5.1 TABLE TRANSFER SUBSYSTEM TABLE ‘EXSTEEL’ TO TABLE ‘WSECT’ TRANSFER ITEMS FROM ‘W14X730’ TO ‘W14X22’ FILE TABLE DELETE TABLE ‘WSECT’ DELETE ITEMS ‘W14X605' ‘W14X455’ ‘W14X287’ ‘W14X219’ FILE TABLE **** FOLLOWING MESSAGE REFERS TO PREVIOUS OPERATION BLOCK **** TABLE MESSAGE 3.2 - TABLE DELETION SUMMARY **** FOLLOWING ITEMS ARE DELETED W14X605 W14X455 W14X287 W14X219 OUTPUT TABLE ‘WSECT’ ***************************** * TABLE OUTPUT WSECT * ***************************** PRINT ITEM NAMES ITEM NAMES W14X730
W14X342
W14X202
W14X142
W14X95
W14X53
W14X665
W14X314
W14X193
W14X320
W14X87
W14X48
W14X550
W14X264
W14X184
W14X136
W14X84
W14X48
W14X500
W14X246
W14X176
W14X127
W14X78
W14X38
W14X426
W14X237
W14X167
W14X119
W14X74
W14X34
W14X398
W14X228
W14X158
W14X111
W14X68
W14X30
W14X370
W14X211
W14X150
W14X103
W14X61
W14X26
W14X22
OUTPUT TABLE <WSECT’ ALL - 47 -
Rev U
Example 5.2
GTTABLE
***************************** * TABLE OUTPUT WSECT * ***************************** HEADINGS AX INCH 2 SY INCH 3 RY INCH AY INCH 2 SZ INCH 3 RZ INCH AZ INCH 2 YD INCH 1 EY INCH IX INCH 4 ZD INCH 1 EZ INCH IY INCH 4 YC INCH 1 FLTK INCH IZ INCH 4 ZC INCH 1 WBTK INCH
1 1 1 1 1 1
YD/AFL COMP WEIGHT ZZ ZY INTYD
INCH -1
RT INCH 1 BF/2TF LB 1 INCH -1 D/TW INCH 3 GRPNUM INCH 3 SHAPE INCH 1
TABLE DATA AX SZ EY ZZ SHAPE W14X730
W12X665
W14X550
W10X500
215.000000 1280.000000 0.000000 1660.000000 1.000000 196.000000 1150.000000 0.000000 1480.000000 1.000000 162.000000 933.000000 0.000000 1180.000000 1.000000 147.000000 840.000000 0.000000 1050.000000 1.000000
Rev U
AY YD EZ ZY
AZ ZD FLTK INTYD
IX YC WBTK RT
IY ZC YD/AFL BF/2TF
IZ RY COMP D/TW
SY RZ WEIGHT GRPNUM
68.867996 117.112999 1450.000000 4720.000000 14400.000000 527.000000 22.440001 17.889000 11.220000 8.94400 4.690000 8.180000 0.000000 4.910000 3.069000 0.255000 1.000000 60.833000 816.000000 12.620000 5.270000 1.820000 7.310000 5.000000 61.238998 106.392998 1120.000000 4170.000000 12500.000000 472.000000 21.670000 17.646000 10.835000 8.823000 4.620000 7.990000 0.000000 4.522000 2.826000 0.272000 1.000000 55.417000 730.000000 12.626000 5.170000 1.950000 7.670000 5.000000 48.340000 20.260000 0.000000 584.000000
87.589996 17.205999 3.818000 12.624000
670.000000 3260.000000 10.130000 8.603000 2.386000 0.308000 5.000000 2.250000
9450.000000 378.000000 4.490000 7.640000 1.000000 45.833000 8.490000 4.000000
42.950001 19.629999 0.000000 522.000000
79.392998 17.007999 3.501000 12.628000
514.000000 2880.000000 9.815000 8.504000 2.188000 0.330000 4.920000 2.430000
8250.000000 339.000000 4.430000 7.490000 1.000000 41.667000 8.970000 4.000000
- 48 -
GTTABLE W16X426
W14X398
W16X370
W14X342
W16X314
W14X264
W16X246
W14X237
125.000000 35.043999 707.000000 18.690001 0.000000 0.000000 869.000000 434.000000 1.000000 117.000000 32.409000 657.000000 18.309999 0.000000 0.000000 802.000000 401.000000 1.000000 109.000000 29.691000 608.000000 17.940001 0.000000 0.000000 737.000000 370.000000 1.000000 101.000000 27.129999 559.000000 17.559999 0.000000 0.000000 673.000000 338.000000 1.000000 92.300003 24.323999 512.000000 17.190001 0.000000 0.000000 611.000000 307.000000 1.000000 77.5999980 19.882000 427.000000 16.500000 0.000000 0.000000 502.000000 254.000000 1.000000 72.300003 18.281000 397.000000 16.250000 0.000000 0.000000 464.000000 235.000000 1.000000 69.699997 17.570999 382.000000 16.120001 0.000000 0.000000 445.000000 225.000000 1.000000
Example 5.2 67.514000 16.695000 3.033000 12.624000
330.000000 2360.000000 9.345000 8.347000 1.875000 0.369000 4.810000 2.750000
6610.000000 283.000000 4.340000 7.260000 1.000000 35.500000 9.970000 4.000000
62.887001 16.590000 2.843000 12.624000
272.000000 2170.000000 9.155000 8.295000 1.770000 0.388000 4.760000 2.920000
6010.000000 262.000000 4.310000 7.170000 1.000000 33.167000 10.300000 4.000000
58.387001 16.475000 2.658000 12.624000
220.000000 1990.000000 8.970000 8.237000 1.655000 0.410000 4.720000 3.100000
5450.000000 241.000000 4.270000 7.080000 1.000000 30.833000 10.800000 4.000000
53.852001 16.365000 2.468000 12.624000
178.000000 1810.000000 8.780000 8.182000 1.545000 0.435000 4.680000 3.320000
4910.000000 221.000000 4.240000 6.990000 1.000000 28.500000 11.400000 4.000000
49.418999 16.235001 2.283000 12.624000
140.000000 1630.000000 8.595000 8.117000 1.415000 0.464000 4.630000 3.560000
4400.000000 201.000000 4.200000 6.900000 1.000000 26.167000 12.100000 4.000000
41.409001 16.025000 1.938000 12.624000
85.300003 1330.000000 8.250000 8.012000 1.205000 0.531000 4.540000 4.130000
3530.000000 166.000000 4.140000 6.740000 1.000000 22.000000 13.700000 4.000000
38.543999 15.945000 1.813000 12.624000
69.699997 1230.000000 8.125000 7.972000 1.125000 0.562000 4.510000 4.400000
3230.000000 154.000000 4.120000 6.680000 1.000000 20.500000 14.400000 4.000000
37.081001 15.910000 1.748000 12.624000
62.599998 1170.000000 8.060000 7.955000 1.090000 0.585000 4.500000 4.550000
3080.000000 148.000000 4.110000 6.650000 1.000000 19.750000 14.800000 4.000000
- 49 -
Rev U
Example 5.2 W16X228
W14X211
W16X202
W14X193
W16X184
W14X176
W16X167
W14X158
67.099998 368.000000 0.000000 427.000000 1.000000 62.099998 339.000000 0.000000 391.000000 1.000000 59.400002 325.000000 0.000000 373.000000 1.000000 56.700001 310.000000 0.000000 355.000000 1.000000 54.099998 296.000000 0.000000 338.000000 1.000000 51.700001 282.000000 0.000000 321.000000 1.000000 49.099998 267.000000 0.000000 303.000000 1.000000 46.500000 253.000000 0.000000 286.000000 1.000000
Rev U
GTTABLE 16.719999 16.000000 0.000000 216.000000
35.707001 15.865000 1.688000 12.624000
56.200001 1120.00000 8.000000 7.932000 1.045000 0.597000 4.480000 4.700000
2940.000000 142.000000 4.100000 6.620000 1.000000 19.000000 15.300000 4.000000
15.435000 15.750000 0.000000 198.000000
32.926998 15.800000 1.563000 12.624000
44.799999 7.875000 0.980000 4.460000
103.000000 7.900000 0.638000 5.050000
2670.000000 130.000000 4.070000 6.560000 1.000000 17.583000 16.100000 3.000000
14.536000 15.630000 0.000000 189.000000
31.563000 15.750000 1.503000 12.624000
39.599998 7.815000 0.930000 4.440000
980.000000 7.875000 0.660000 5.240000
2540.000000 124.000000 4.060000 6.540000 1.000000 16.833000 16.799999 3.000000
13.795000 15.500000 0.000000 180.000000
30.121000 15.710000 1.438000 12.624000
34.700001 7.750000 0.890000 4.420000
930.000000 7.855000 0.686000 5.460000
2400.000000 118.000000 4.050000 6.510000 1.000000 16.083000 17.400000 3.000000
12.919000 15.380000 0.000000 171.000000
28.773001 15.660000 1.378000 12.624000
30.299999 7.690000 0.840000 4.410000
883.000000 7.830000 0.713000 5.680000
2270.000000 113.000000 4.040000 6.490000 1.000000 15.333000 18.299999 3.000000
12.505000 15.250000 0.000000 163.000000
27.379999 15.640000 1.313000 12.624000
26.500000 7.625000 0.820000 4.390000
838.000000 7.820000 0.743000 5.960000
2150.000000 107.000000 4.020000 6.450000 1.000000 14.667000 18.600000 3.000000
11.794000 15.120000 0.000000 154.000000
25.958000 15.600000 1.248000 12.624000
22.799999 7.560000 0.780000 4.380000
790.000000 7.800000 0.777000 6.250000
2020.000000 101.000000 4.010000 6.420000 1.000000 13.917000 19.400000 3.000000
10.950000 15.000000 0.000000 145.000000
24.631001 15.550000 1.188000 12.624000
19.500000 7.500000 0.730000 4.360000
745.000000 7.775000 0.812000 6.540000
1900.000000 4.000000 1.000000 20.500000
- 50 -
95.800003 6.400000 13.167000 3.000000
GTTABLE W16X150
W14X142
W16X320
W14X136
W16X127
W14X119
W16X111
W14X103
44.099998 240.000000 0.000000 270.000000 1.000000 41.799999 227.000000 0.000000 255.000000 1.000000 94.099998 493.000000 0.000000 592.000000 1.000000 40.000000 216.000000 0.000000 243.000000 1.000000 37.299999 202.000000 0.000000 226.000000 1.000000 35.000000 189.000000 0.000000 211.000000 1.000000 32.700001 176.000000 0.000000 196.000000 1.000000 30.299999 164.000000 0.000000 181.000000 1.000000
Example 5.2 10.342000 14.880000 0.000000 137.000000
23.334999 15.515000 1.128000 12.624000
16.700001 7.440000 0.695000 4.350000
703.00000 7.757000 0.850000 6.880000
1790.000000 3.990000 1.000000 21.400000
90.599998 6.370000 12.500000 3.000000
10.030000 14.750000 0.000000 129.000000
21.969000 15.500000 1.063000 12.624000
14.200000 7.375000 0.680000 4.330000
660.000000 7.750000 0.895000 7.290000
1670.000000 3.970000 1.000000 21.700001
85.199997 6.320000 11.833000 3.000000
31.771000 16.809999 0.000000 304.000000
46.632000 16.709999 2.093000 12.624000
9.735000 14.750000 0.000000 117.000000
20.891001 14.740000 1.063000 12.624000
13.500000 7.375000 0.660000 4.120000
568.000000 7.370000 0.941000 6.930000
1590.000000 3.770000 1.000000 22.299999
77.000000 6.310000 11.333000 2.000000
8.918000 14.620000 0.000000 109.000000
19.547001 14.690000 0.998000 12.624000
11.100000 7.310000 0.610000 4.100000
528.000000 7.345000 0.997000 7.360000
1480.000000 3.760000 1.000000 24.000000
71.800003 6.290000 10.583000 2.000000
8.265000 14.500000 0.000000 102.000000
18.322001 14.650000 0.938000 12.624000
9.200000 7.250000 0.570000 4.080000
492.000000 7.325000 1.055000 7.810000
1370.000000 3.750000 3.000000 25.400000
67.099998 6.260000 9.917000 2.000000
7.760000 14.370000 0.000000 94.300003
17.018000 14.620000 0.873000 12.624000
7.480000 7.185000 0.540000 4.070000
455.000000 7.310000 1.126000 8.370000
1270.000000 3.730000 3.000000 26.600000
62.200001 6.230000 9.250000 2.000000
7.054000 14.250000 0.000000 87.199997
15.799000 14.575000 0.813000 12.624000
6.020000 7.125000 0.495000 4.050000
420.000000 7.287000 1.203000 8.960000
1170.000000 3.720000 2.000000 28.799999
57.599998 6.210000 8.583000 2.000000
137.000000 1640.000000 8.405000 8.355000 1.890000 0.481000 4.730000 3.990000
- 51 -
4140.000000 196.000000 4.170000 6.630000 1.000000 26.667000 8.890000 4.000000
Rev U
Example 5.2
GTTABLE
W14X95
27.900000 151.000000 0.000000 166.000000 1.000000
6.566000 14.120000 0.000000 79.900002
14.506000 14.545000 0.748000 12.624000
4.740000 7.060000 0.465000 4.040000
384.000000 7.272000 1.298000 9.720000
1060.000000 3.710000 2.000000 30.400000
52.799999 6.170000 7.917000 2.000000
W16X87
25.600000 138.000000 0.000000 151.000000 1.000000 24.700001 131.000000 0.000000 145.000000 1.000000 22.900000 121.000000 0.000000 134.000000 1.000000 21.799999 112.000000 0.000000 126.000000 1.000000 20.000000 103.000000 0.000000 115.000000 1.000000 17.900000 92.199997 0.000000 102.000000 1.000000 15.600000 77.800003 0.000000 87.099998 1.000000
5.880000 14.000000 0.000000 73.000000
13.301000 14.500000 0.688000 12.624000
3.680000 7.000000 0.420000 4.020000
350.000000 7.250000 1.403000 10.500000
967.000000 3.700000 2.000000 33.299999
48.200001 6.150000 7.250000 2.000000
6.395000 14.180000 0.000000 57.000000
12.472000 12.023000 0.778000 12.624000
4.410000 7.090000 0.451000 3.320000
225.000000 6.011000 1.516000 7.730000
928.000000 3.020000 3.000000 31.400000
37.500000 6.130000 7.000000 2.000000
6.018000 14.060000 0.000000 52.400002
11.488000 12.000000 0.718000 12.624000
3.520000 7.030000 0.428000 3.310000
207.000000 6.000000 1.632000 8.360000
851.000000 3.000000 3.000000 32.900002
34.500000 6.090000 6.500000 2.000000
6.385000 14.190000 0.000000 40.500000
10.515000 10.072000 0.783000 12.624000
3.860000 7.095000 0.450000 2.760000
133.000000 5.036000 1.799000 6.430000
797.000000 2.480000 1.000000 31.500000
26.500000 6.050000 6.167000 2.000000
5.877000 14.060000 0.000000 36.799999
9.612000 10.040000 0.718000 12.624000
3.010000 7.030000 0.418000 2.740000
121.000000 5.020000 1.950000 6.990000
724.000000 2.460000 1.000000 33.599998
24.100000 6.020000 5.667000 2.000000
5.258000 13.910000 0.000000 32.700001
8.573000 10.000000 0.643000 12.624000
2.190000 6.955000 0.378000 2.730000
107.000000 5.000000 2.163000 7.780000
641.000000 2.450000 3.000000 36.799999
21.500000 5.980000 5.083000 2.000000
5.158000 13.940000 0.000000 21.900000
7.073000 8.062000 0.658000 12.624000
1.930000 6.970000 0.370000 2.180000
57.50000 4.031000 2.628000 6.130000
542.000000 1.920000 1.000000 37.700001
14.300000 5.900000 4.417000 1.000000
W14X84
W16X78
W14X74
W16X68
W14X61
W16X53
Rev U
- 52 -
GTTABLE W14X48
W16X43
W14X38
W16X34
W14X30
W16X26
W14X22
14.100000 70.199997 0.000000 78.400002 1.000000 12.600000 62.700001 0.000000 69.699997 1.000000 11.200000 54.700001 0.000000 61.599998 1.000000 10.000000 48.599998 0.000000 54.599998 1.000000 8.830000 41.900002 0.000000 47.200001 1.000000 7.670000 35.099998 0.000000 40.000000 1.000000 6.490000 28.900000 0.000000 33.099998
Example 5.2 4.682000 13.810000 0.000000 19.600000
6.350000 8.031000 0.593000 12.624000
1.440000 6.905000 0.339000 2.160000
51.299999 4.015000 2.900000 6.770000
485.000000 1.910000 1.000000 40.700001
12.800000 5.860000 4.000000 1.000000
4.213000 13.680000 0.000000 17.299999
5.632000 8.000000 0.528000 12.624000
1.050000 6.840000 0.308000 2.140000
45.099998 4.000000 3.239000 7.580000
429.000000 1.890000 3.000000 44.400002
11.300000 5.820000 3.583000 1.000000
4.420000 14.120000 0.000000 12.100000
4.635000 6.776000 0.513000 13.094000
0.796000 7.060000 0.313000 1.800000
26.600000 3.388000 4.062000 6.600000
386.000000 1.540000 1.000000 45.099998
7.860000 5.880000 3.167000 1.000000
4.018000 14.000000 0.000000 10.600000
4.077000 6.750000 0.453000 13.094000
0.567000 7.000000 0.287000 1.780000
23.299999 3.375000 4.579000 7.450000
340.000000 1.520000 3.000000 48.799999
6.890000 5.830000 2.833000 1.000000
3.742000 13.860000 0.000000 8.950000
3.438000 6.733000 0.383000 13.094000
0.376000 6.930000 0.270000 1.750000
19.500000 3.366000 5.375000 8.790000
290.000000 1.490000 3.000000 51.299999
5.800000 5.740000 2.500000 1.000000
3.542000 13.890000 0.000000 5.520000
2.801000 5.025000 0.418000 13.054000
0.355000 6.945000 0.255000 1.290000
8.860000 2.512000 6.613000 6.010000
244.000000 1.080000 1.000000 54.500000
3.530000 5.640000 2.167000 1.000000
3.156000 13.720000 0.000000 4.390000
2.233000 5.000000 0.335000 13.050000
0.208000 6.860000 0.230000 1.260000
7.000000 2.500000 8.191000 7.460000
198.000000 1.040000 3.000000 59.700001
2.800000 5.530000 1.833000 1.000000
FINISH
- 53 -
Rev U
Example 5.2
GTTABLE
End of Document.
Rev U
- 54 -
®
GTTABLE Manual
Computer-Aided Structural Engineering Center School of Civil & Environmental Engineering Georgia Institute of Technology Atlanta Georgia 30332-0355 USA www.gtstrudl.gatech.edu
This page intentionally left blank.
Rev U
- ii -
NOTICES GTSTRUDL® Reference Manual, GTTABLE, Revision U is applicable to Version 30 of GTSTRUDL released April 2009 and subsequent versions. GTSTRUDL® computer program is proprietary to and a trade secret of the Georgia Tech Research Corporation, Atlanta, Georgia 30332. GTSTRUDL® is a ed service mark of the Georgia Tech Research Corporation, Atlanta, Georgia, U.S.A.
DISCLAIMER NEITHER GEORGIA TECH RESEARCH CORPORATION NOR GEORGIA INSTITUTE OF TECHNOLOGY MAKE ANY WARRANTY EXPRESSED OR IMPLIED AS TO THE DOCUMENTATION, FUNCTION, OR PERFORMANCE OF THE PROGRAM DESCRIBED HEREIN AND THE S OF THE PROGRAM ARE EXPECTED TO MAKE THE FINAL EVALUATION AS TO THE USEFULNESS OF THE PROGRAM IN THEIR OWN ENVIRONMENT. Commercial Software Rights Legend Any use, duplication, or disclosure of this software by or for the U.S. Government shall be restricted to the of a license agreement in accordance with the clause at DFARS 227.7202-3 (June 2005). This material may be reproduced by or for the U.S. Government pursuant to the copyright license under the clause at DFARS 252-227-7013, September 1989. Georgia Tech Research Corporation Georgia Institute of Technology Atlanta, Georgia 30332-0355 Copyright © 2009 Georgia Tech Research Corporation Atlanta, Georgia 30332 ALL RIGHTS RESERVED Printed in United States of America - iii -
Rev U
This page intentionally left blank.
Rev U
- iv -
GTSTRUDL Manual Revision History Revision No.
Date Released
U
4/2009
Description GTSTRUDL Reference Manual, GTTABLE, has been updated and is applicable to Version 30 of GTSTRUDL and subsequent versions. .
-v-
Rev U
This page intentionally left blank.
Rev U
- vi -
Table of Contents Section
Page
NOTICES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii DISCLAIMER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii GTSTRUDL Reference Manual Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii List of Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii List of Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii
1.0 1.1 1.2
GTTABLE Subsystem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 GTTABLE Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.0
INITIATE Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3.1 3.2
ADD HEADINGS Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 ADD ITEMS Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.1 4.2
MODIFY Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 MODIFY ITEMS Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.1 5.2 5.3
ORDER Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 ORDER BY Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 ARRANGE Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
6.1 6.2
TRANSFER Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 TRANSFER ITEMS Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
7.1 7.2 7.3
DELETE Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 DELETE HEADINGS Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 DELETE ITEMS Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
8.1 8.2 8.3 8.4 8.5
OUTPUT Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 PRINT HEADINGS Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 PRINT ITEMS Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 PRINT ITEM NAMES Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 PRINT ORDERINGS Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 - vii -
Rev U
Section
Page
9.0
UNITS Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
10.0
LIST Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
11.0
CHANGE Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
12.1 12.2 12.3 12.4 12.5 12.6 12.7
EXAMPLE 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 EXAMPLE 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 EXAMPLE 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 EXAMPLE 4.1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 EXAMPLE 4.2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 EXAMPLE 5.1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 EXAMPLE 5.2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
List of Figures Figure 1.1-1 Figure 1.1-2
GTSTRUDL Table Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 GTSTRUDL Table ‘EXSTEEL’, Example 4.1 AND 4.2 . . . . . . . . . . . . . . . . . 2
List of Tables Table 12.2-1 Table 12.3-1
Rev U
GTSTRUDL Table Properties for Analysis . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 GTSTRUDL Table Properties for Analysis and Steel Design . . . . . . . . . . . . 37
- viii -
GTTABLE
1.0
GTTABLE Subsystem
1.1
Introduction
GTTABLE Commands
GTTABLE is a subsystem which provides the with a convenient language for storing and retrieving tabular data. These data are then available for use by other subsystems, GTSTRUDL for example. Originally implemented as a stand-alone subsystem, GTTABLE, is now an integrated part of GTSTRUDL. The purpose of this Manual is to familiarize the with how to create and modify tables. Tables created by GTTABLE are structured as shown in Figures 1.1-1 and 1.1-2. These tables are two-dimensional arrays with an arbitrary number of columns and rows containing data. Each row represents a unique item within a given table, while each column represents a unique heading for data in the table. The names of items and headings may be up to eight characters long. GTTABLE provides for two data sets in which tables may be stored; one a data set, and the second a subsystem (GTSTRUDL) data set. Both data sets allow the to protect data in a table by specifying a unique for each table. Data in any table are always available for output, even when the table is protected. Besides the simple inputting and outputting of the tabular data, the information within the table also can be ordered. The items in a table can be ordered by increasing or decreasing value of a particular heading. Such orderings may then be used to arrange other headings in the table. The orderings and arrangements created by GTTABLE may be used by other subsystems to aid searches through a particular table. As the commands of GTTABLE are described, the examples presented will construct the table in Figure 1.1-2. This table will be referred to by the name ‘EXSTEEL’, and it will be placed in the data set. At the conclusion of this report the complete sequence of commands will be presented.
-1-
Rev U
GTTABLE Commands
GTTABLE
TABLE HEADING NAMES Table Item Names
Figure 1.1-1
WEIGHT (lb/ft)
AX (in2)
Heading values stored by item
General Table Format
DEPTH (in)
IZ (in4)
IY (in4)
SZ (in3)
‘W14X90'
90.0
26.5
14.02
999.0.
362.0
143.0
‘W12X58'
58.0
17.0
12.19
475.0
107.0
78.0
‘W4X13'
13.0
3.83
4.16
11.3
3.86
5.46
‘W10X100'
100.0
29.4
11.1
623.0
207.0
112.0
‘W16X50'
50.0
14.7
16.26
659.0
37.2
81.0
‘C5X9'
9.0
2.64
5.0
8.9
0.632
3.56
Figure 1.1-2
Rev U
Example Table ‘EXSTEEL’, Example 4.1 and 4.2
-2-
GTTABLE
1.2
GTTABLE Commands
GTTABLE Commands
GTTABLE commands are organized into table operation blocks. Each operation block performs one of the following functions: INITIATE MODIFY DELETE OUTPUT ORDER TRANSFER Each table operation block must begin with an operation heading command. Specific operation commands may be given only after the appropriate operation heading command is given. All Table operation blocks, except OUTPUT, must be closed with a ‘FILE TABLE’ command. In the discussion that follows the GTTABLE commands are presented in operation blocks. An operation heading command is described, then the specific operation commands appropriate for that block are described. Before any specific command or operation heading commands can be processed, the TABLE command must be given. This is accomplished with the following command: TABLE (‘title’)
Elements: ‘title’ = an optional 64-character description of the TABLE job which follows. After TABLE command is given, the GTTABLE commands described in the remainder of this document can be given.
-3-
Rev U
GTTABLE Commands
GTTABLE
This page intentionally left blank.
Rev U
-4-
GTTABLE
2.0
INITIATE Command
INITIATE Command
( ) Indicates optional keywords. { } Indicates a choice of keywords.
name
= The name of the table that is being created, which cannot be more than 8 characters and is required.
= Optional for the particular table being created. If a is given here, it must be given on all other commands specifying a . This command is used to create a new table. The table may be created under the data set. A may be attached with the particular table if so desired. Once a new table has been initiated with this command, the following commands may be used with this operation block: ADD HEADING ADD ITEMS MODIFY ITEMS
EXAMPLE: INITIATE TABLE <EXSTEEL’ or INI ‘EXSTEEL’
The above examples all create the same table ‘EXSTEEL’ in the data set without a .
-5-
Rev U
INITIATE Command
GTTABLE
This page intentionally left blank.
Rev U
-6-
GTTABLE
3.1
ADD HEADINGS Command
ADD HEADINGS Command ADD HEADINGS ‘nameh1’ dimension (n) ‘nameh2’ dimension (n) C C C C C C namehi
=
... ... C C C Name of the heading to be added to the table with no more than 8 characters. No duplication of names may exist within a table.
*
This command may be used in either the INITIATE or MODIFY an operation block. This command allows the creation of new headings in the table. The ADD HEADINGS command is followed by the name of the heading and the associated dimensions. The value of n corresponds to the exponent of the dimension, assume 1 if not given.
EXAMPLE: ADD HEADINGS <WEIGHT’ WEIGHT 1 LENGTH –1
-7-
Rev U
ADD ITEMS Command
3.2
GTTABLE
ADD ITEMS Command ADD ITEMS ‘names1’ ‘names2’ C C C
(
‘nameh1’ v11 v21 C C C
namehi
=
Name of the heading under which information for the item is input. These names may be omitted in which case the values entered will correspond to the headings as they were created.
namesi
=
Name of the item being added, which is up to 8 characters in length. No duplication of names may exist.
vim
=
‘nameh2’ v12 v22 C C C
‘nameh2' v13 v23 C C C
... ) ... ... C C C
Data value for item i and heading m.
This command can be used in the INITIATE and MODIFY operation blocks. It is used to add new items to the table.
EXAMPLE: UNITS INCH POUND ADD ITEMS ‘WEIGHT’ ‘W14X90’ 7.5 ‘W12X58’ 4.8333 ‘W4X13’ 1.0833 ‘W10X100’ 8.3333 ‘W16X50’ 4.1667 ‘C5X9’ 0.75 FILE TABLE
‘AX’ 26.5 17.0 3.83 29.4 14.75 2.64
‘YD’ 14.02 12.19 4.16 11.1 16.26 5.0
‘IZ’ 990.0 475.0 11.3 623.0 659.0 8.9
‘IY’ 362.0 107.0 3.86 207.0 37.2 0.632
‘SZ’ 143.0 78.0 5.46 112.0 81.0 3.56
Note that the value of AX for the item W16X50 intentionally is specified as 14.75 so we can show how to use the MODIFY ITEMS option to change it to 14.7.
Rev U
-8-
GTTABLE
4.1
MODIFY Command
MODIFY Command
name = Name of the existing table that is to be modified. { }
Indicates a choice of keywords.
( )
Indicates an optional keyword.
This operation heading command is used to CHANGE or ADD information in an existing table. If a was used when the table was created, it must be included here also. Once the has specified the MODIFY statement, the following commands may be used: ADD HEADINGS ADD ITEMS MODIFY ITEMS
EXAMPLE: MODIFY TABLE
‘WSHAPES’
‘MYWD’
-9-
Rev U
MODIFY ITEMS Command
4.2
GTTABLE
MODIFY ITEMS Command MODIFY ITEMS
( ‘nameh1’ ‘nameh2’ ... )
‘names1’
v11
v12
...
‘names2’
v21
v22
...
namehi
=
Name of an existing heading within the table that is to be modified. If the heading names are omitted, the new values for each item will be assigned in the same order as they were given in the ADD HEADINGS command.
namesi
=
Name of an existing item within the table that is to be modified.
vim
=
The new value for the item i and heading m.
This command can be used with the operation heading command MODIFY. The operation heading command (MODIFY) must appear before the MODIFY ITEMS command.
EXAMPLE: MODIFY TABLE ‘EXSTEEL’ MODIFY ITEMS ‘AX’ ‘W16X50’ 14.7 FILE TABLE
This example replaces the old value of AX for section ‘W16X50’ with the new value of 14.70.
Rev U
- 10 -
GTTABLE
5.1
ORDER Command
ORDER Command
name
=
Name of the existing table that is to be ordered.
=
The current for the table specified.
This operation heading command is used to order a heading within a table. An ordering may also be arranged according to another heading. The allowable commands in this operation block are: ORDER BY ARRANGE
If the keywords ‘FOR STRUDL’ are included, table will automatically produce the orderings used by GTSTRUDL. When this is done, no other commands should be used in the ORDER operation block. FILE TABLE should always end this operation block.
EXAMPLE: ORDER TABLE ‘EXSTEEL’ ORDER BY INCREASING ‘AX’ ARRANGE ‘SZ’ ON ORDERING ‘AX’ WITH ID ‘AXSZ’ FILE TABLE
- 11 -
Rev U
ORDER BY Command
5.2
GTTABLE
ORDER BY Command
namehi
=
Name of a heading within the table that is to be ordered.
This command is used with the ORDER operation heading command. This command is used to specify what heading is to be ordered and in what direction the ordering is to proceed. This command should be followed by FILE TABLE.
EXAMPLE: ORDER TABLE ‘EXSTEEL’ ORDER BY INCREASING ‘AX’ ARRANGE ‘SZ’ ON ORDERING ‘AX’ WITH ID ‘AXSZ’ FILE TABLE
Rev U
- 12 -
GTTABLE
5.3
ARRANGE Command
ARRANGE Command ARRANGE ‘name2’ (ON) (ORDERING) ‘name1’ (WITH) (ID) ‘id’
name2
=
Name of the heading that is to be arranged according to ordering name1.
name1
=
Name of an existing ordering.
id
=
Name for the arrangement different from name1 and name2.
This command is used within the ORDER operation block. It arranges the specified heading in the same sequence as a specified ordering. The ordering should already exist.
EXAMPLE: ORDER TABLE ‘EXSTEEL’ ORDER BY INCREASING ‘AX’ ARRANGE ‘SZ’ ON ORDERING ‘AX’ WITH ID ‘AXSZ’ FILE TABLE
- 13 -
Rev U
ARRANGE Command
GTTABLE
This page intentionally left blank.
Rev U
- 14 -
GTTABLE
6.1
TRANSFER Command
TRANSFER Command
name1
=
Name of the existing table where the data is located.
name2
=
Name of the table where the data is to be placed, it may be a new or existing table.
=
for the second table, which must agree if the table has been already created.
ALL
Optional, but if used all of the data will be transferred. Orderings cannot be transferred.
=
{ } Indicates a choice between keywords. ( )
Indicates an optional keyword.
This operation heading command is used to transfer all or part of an existing table to another table that already exists or to a new table. Allowable operations within this operation heading block are: TRANSFER ITEMS
- 15 -
Rev U
TRANSFER ITEMS Command
6.2
GTTABLE
TRANSFER ITEMS Command
itemi
=
Item to be transferred to the other table.
n1
=
Position of the first item to be transferred.
n2
=
Position of the last item to be transferred.
This command may only be used within the TRANSFER heading block. This command is used to transfer only a portion of an existing table to another table.
Rev U
- 16 -
GTTABLE
7.1
DELETE Command
DELETE Command
{ }
Indicates a choice between keywords.
(
Indicates an optional keyword.
)
This operation heading command is used to delete all or part of an existing table. If a was used when the table was created, then the must be specified here. The other commands allowed within this operation heading block are: DELETE ITEMS DELETE HEADINGS If ‘ALL’ is specified, the entire table is deleted and no other commands are necessary. If ‘ALL’ is not specified, then one of the allowable commands below (DELETE HEADINGS or DELETE ITEMS) is expected to follow this command.
- 17 -
Rev U
DELETE HEADINGS and DELETE ITEMS Command
7.2
GTTABLE
DELETE HEADINGS Command DELETE HEADINGS ‘nameh1’ ‘nameh2’ ...
namehi
=
Name of the existing heading that is to be deleted in the table. The deletion removes all values under that heading and also removes all orderings within the table.
This command must be preceded by the DELETE operation heading command.
7.3
DELETE ITEMS Command DELETE ITEMS ‘names1’ ‘names2’ ...
namesi
=
Name of the existing item in the table that is to be deleted. The deletion also removes all orderings in that table.
This command must be preceded by the DELETE operation heading command.
Rev U
- 18 -
GTTABLE
8.1
OUTPUT Command
OUTPUT Command
name
=
Name of the table to be output.
FORMAT F
=
The output is in decimal point form with 6 digits to the right of the decimal.
FORMAT E
=
This output is in exponential form.
ALL
=
If given in this command, the entire table is output including orderings and arrangements. If ‘ALL’ is not given, then the allowable PRINT commands are expected to follow.
This operation heading command is used to output the table information. A is not needed to obtain the information. The allowable commands within this operation heading command are: PRINT HEADINGS PRINT ITEMS PRINT ITEM NAMES PRINT ORDERINGS
- 19 -
Rev U
PRINT HEADINGS and PRINT ITEMS Command
8.2
GTTABLE
PRINT HEADINGS Command PRINT HEADINGS ‘nameh1’ ‘name2’ ...
namehi
=
Name of the heading to be output. If no names are given, then all of the headings will be output.
This command is contained in the OUTPUT operation heading command. This command initializes what headings are to be output for the given items to follow in the PRINT ITEMS command.
8.3
PRINT ITEMS Command
itemi = Name of the item to be output. n1
= Position of first item to be output.
n2
= Position of second item to be output.
This command is contained in the OUTPUT operation heading command. This command specifies which items are to be output.
Rev U
- 20 -
GTTABLE
8.4
PRINT ITEM NAMES, PRINT ORDERINGS
PRINT ITEM NAMES Command PRINT ITEM NAMES
This command is used within the OUTPUT operation heading command. It is used to obtain a listing of the item names within the table, but not the associated data values.
8.5
PRINT ORDERINGS Command PRINT ORDERINGS
nameoi
=
‘nameo1’
‘nameo2’ ...
Name of the ordering to be output.
This command is contained within the OUTPUT operation heading command. This command outputs the orderings listed for the table.
- 21 -
Rev U
PRINT ITEM NAMES and PRINT ORDERINGS Command
This page intentionally left blank.
Rev U
- 22 -
GTTABLE
GTTABLE
9.0
UNITS Command
UNITS Command *
{ } Indicates a choice of keywords. * Indicates more than one choice can be made. This command may be used between operation blocks to specify a new set of units. Initially the units are automatically set to inches, pounds, radians, second, and Fahrenheit. There are five areas of units which are: length, force, angle, time, temperature. One or more of the units may be specified at any time.
EXAMPLE: UNITS MM KN DEGREE
- 23 -
Rev U
UNITS Command
GTTABLE
This page intentionally left blank.
Rev U
- 24 -
GTTABLE
LIST Command
10.0 LIST Command Output Tables in the data set (DAT.DS). FLIST 1 Output Tables in the SUBSYSTEM data set (GTSTRUDL Table database). FLIST 2
This operation may be used between operation blocks to find out what tables are contained on each data set.
- 25 -
Rev U
CHANGE Command
GTTABLE
This page intentionally left blank.
Rev U
- 26 -
GTTABLE
LIST Command
11.0 CHANGE Command
name = Name of the table for which the is to be changed.
This command allows the to change the for a table. The command should be used between operation heading blocks. If the old is non-existent, then the ‘FROM OLDPSWD’ can be omitted.
- 27 -
Rev U
CHANGE Command
GTTABLE
This page intentionally left blank.
Rev U
- 28 -
GTTABLE
EXAMPLE 1
12.1 EXAMPLE 1: Building a Table from an Existing table GTTABLE can be used to build special subsets of the subsystem tables provided with GTSTRUDL. s of the Member Selection capabilities of GTSTRUDL should consider building special tables, since they can increase the efficiency of the selection process. The following example shows how a table of W14 shapes is built from the GTSTRUDL table WSHAPES9. In addition, several W14s are deleted from the resulting table. TABLE ‘Building Special Tables’ $ TRANSFER SUBSYSTEM TABLE ‘WSHAPES9’ TO TABLE ‘W14’ TRANSFER ITEMS FROM ‘W14X730’ TO ‘W14X22’ FILE TABLE $ DELETE TABLE ‘W14’ DELETE ITEMS ‘W14X605’ ‘W14X455’ ‘W14X283’ ‘W14X211’ FILE TABLE $ ORDER TABLE ‘W14’ ORDER BY INCREASING ‘AX’ ARRANGE ‘SY’ ON ORDERING ‘AX’ WITH ID ‘AXSY’ ARRANGE ‘SZ’ ON ORDERING ‘AX’ WITH ID ‘AXSZ’ FILE TABLE $ OUTPUT TABLE ‘W14’ ALL $ FINISH The above example creates a special table of W14 shapes, which is to be permanently stored on the data set (DAT.DS).
- 29 -
Rev U
EXAMPLE 2
GTTABLE
12.2 EXAMPLE 2: Building a New Table s of GTSTRUDL may find it convenient to build their own tables of frequently used member properties. The following example illustrates how such a table can be built. The table WELDPG supplies only those properties required by GTSTRUDL for analysis, as described in Table 12.2-1. If the table is to be used for member selection or checking, additional properties must be included in the table (see Example 3 of Section 12.3 for ISHAPES and Table 12.3-1 for properties description). The specific properties to be added for member selection depend on the cross-sectional shape of the profile, and the GTSTRUDL design code being used. The is referred to Volume 2A, Section ASD9, TOWER2, etc. for a description of additional properties required for member selection. Properties are given after the profile name in the same order as given in the ADD HEADINGS command. s must the accuracy of all tables they build, as no internal checks are made in GTSTRUDL of data taken from tables. Properties which are not included in a particular table are taken as zero by GTSTRUDL.
Rev U
- 30 -
GTTABLE
EXAMPLE 2
TABLE 'Building a New Table' $ $ This Table has the required properties for ANALYSIS only. $ INITIATE TABLE 'WELDPG' $ ADD HEADINGS 'AX' LENGTH 2 'AY' LENGTH 2 'AZ' LENGTH 2 'IX' LENGTH 4 'IY' LENGTH 4 'IZ' LENGTH 4 'YD' LENGTH 1 'YC' LENGTH 1 'ZD' LENGTH 1 'ZC' LENGTH 1 'SY' LENGTH 3 'SZ' LENGTH 3 'EY' LENGTH 1 'EZ' LENGTH 1 $ ADD ITEMS $ 'PG92X823' 241.8750 61.8750 120.0000 549.7485 431105.6250 96.0000 48.0000 30.0000 900.1625 8981.3672 0.0000 0.0000 $ 'PG92X517' 151.8750 61.8750 60.0000 77.2485 230158.1250 93.0000 46.5000 30.0000 450.1625 4949.6372 0.0000 0.0000 $ 'PG86X654' 192.5000 52.5000 93.3333 298.5026 292821.6875 89.0000 44.5000 28.0000 653.4554 6580.2627 0.0000 0.0000
- 31 -
13502.4375 15.0000 -
6752.4370 15.0000 -
9148.3760 14.0000 -
Rev U
EXAMPLE 2 $ 'PG86X464'
$ 'PG74X423'
$ 'PG74X301'
$ 'PG49X197'
$ 'PG45X128'
$ 'PG36X300'
GTTABLE 136.5000 184401.0000 392.1221
52.5000 87.0000 4239.1035
56.0000 43.5000 0.0000
69.8359 28.0000 0.0000
5489.7090 14.0000 -
124.6125 132504.2813 336.0892
40.6125 75.7000 3500.7737
56.0000 37.8500 0.0000
90.0333 24.0000 0.0000
4033.0708 12.0000 -
88.5000 81448.0000 192.0890
40.5000 74.0000 2201.2974
32.0000 37.0000 0.0000
20.2715 24.0000 0.0000
2305.0679 12.0000 -
58.0000 27716.8340 106.6930
18.0000 50.5000 1097.6964
26.6667 25.2500 0.0000
21.6771 16.0000 0.0000
853.5443 8.0000 -
37.7500 14234.8330 64.0140
13.7500 45.5000 625.7070
16.0000 22.7500 0.0000
4.9476 16.0000 0.0000
512.1119 8.0000 -
87.5049 20138.9023 155.6197
31.5441 36.7400 1096.2930
37.3072 18.3700 0.0000
62.0378 16.6550 0.0000
1295.9235 8.3275 -
$ FILE TABLE $ $ OUTPUT TABLE 'WELDPG' ALL $ FINISH
Rev U
- 32 -
GTTABLE
EXAMPLE 2 Table 12.2-1
GTSTRUDL Table Properties for Analysis Property
Description
AX
Cross-section area
AY
Y-axis shear area
AZ
Z-axis shear area
IX
Torsion constant
IY
Y-axis moment of inertia
IZ
Z-axis moment of inertia
YD
Depth parallel to Y-axis
YC
Distance from centroid to extreme fiber in positive Y direction
ZD
Depth parallel to Z-axis
ZC
Distance from centroid to extreme fiber in positive Z direction
SY
Y-axis section modulus
SZ
Z-axis section modulus
EY
Distance from centroid to shear center parallel to the Y-axis
EZ
Distance from centroid to shear center parallel to the Z-axis
- 33 -
Rev U
EXAMPLE 3
GTTABLE
12.3 EXAMPLE 3: Building a New Table for Analysis and Design TABLE 'Building a New Table for Analysis and Design' $ INITIATE TABLE 'ISHAPES' $ $ ADD HEADINGS 'ND' LENGTH 1 'WEIGHT' WEIGHT 1 LENGTH -1 'AX' LENGTH 2 'AY' LENGTH 2 'AZ' LENGTH 2 'YD' LENGTH 1 'WBTK' LENGTH 1 'ZD' LENGTH 1 'FLTK' LENGTH 1 'BF/2TF' 'D/TW' 'RT' LENGTH 1 'YD/AFL' LENGTH -1 'IZ' LENGTH 4 'SZ' LENGTH 3 'SZS' LENGTH 3 'RZ' LENGTH 1 'IY' LENGTH 4 'SY' LENGTH 3 'SYS' LENGTH 3 'RY' LENGTH 1 'ZZ' LENGTH 3 'ZY' LENGTH 3 'IX' LENGTH 4 'CW' LENGTH 6 'INTYD' LENGTH 1 'YC' LENGTH 1 'ZC' LENGTH 1 'EY' LENGTH 1 'EZ' LENGTH 1
Rev U
- 34 -
GTTABLE
EXAMPLE 3
'GRPNUM' 'SHAPE' $ $ ADD ITEMS $ $ 'W16X50'
'W14X48'
'W12X45'
'S8X23'
16.000 16.260 42.800 81.000 1.590 15.000 1.000 14.000 13.790 40.600 70.300 1.910 12.600 1.000 12.000 12.060 36.000 58.100 1.940 10.910 1.000 8.000 8.000 18.100 16.200 0.798 7.148 1.000
4.167 0.380 1.840 6.680 92.000 8.130 1.000 4.000 0.340 2.130 5.850 78.400 6.895 1.000 3.750 0.335 2.150 5.150 64.700 6.030 1.000 1.917 0.441 0.950 3.100 0.550 4.000 1.100
- 35 -
14.700 7.070 3.650 37.200 16.300 3.535
6.179 0.630 659.000 10.500 1.520 0.000
5.939 5.600 81.000 10.500 2270.000 0.000
-
14.100 8.030 2.890 51.400 19.600 4.015
4.689 0.595 485.000 12.800 1.460 0.000
6.370 6.700 70.300 12.800 2240.000 0.000
-
13.200 8.045 2.610 50.000 19.000 4.022
4.040 0.575 350.000 12.400 1.310 0.000
6.168 7.000 58.100 12.400 1650.000 0.000
-
6.770 4.171 4.510 4.310 19.300 2.086
3.528 0.426 64.900 2.070 3.680 0.000
2.369 4.900 16.200 2.070 61.800 0.000
-
Rev U
EXAMPLE 3 'HP8X36'
'M10X9'
GTTABLE 8.000 8.020 18.000 29.800 1.950 7.130 2.000 10.000 10.000 63.700 7.760 0.480 9.588 1.000
3.000 0.445 2.180 3.360 0.770 4.010 1.200 0.750 0.157 0.610 3.830 0.030 5.000 1.300
10.600 8.155 2.210 40.300 33.600 4.078
3.569 0.445 119.000 9.880 15.200 0.000
4.839 9.200 29.800 9.880 578.000 0.000
-
2.650 2.690 18.000 0.609 9.190 1.345
1.570 0.206 38.800 0.453 0.765 0.000
0.739 6.500 7.760 0.453 14.600 0.000
-
FILE TABLE $ $ $ Following ORDER command is required for SELECT command. $ ORDER TABLE 'ISHAPES' FOR STRUDL FILE TABLE $ OUTPUT TABLE 'ISHAPES' FORMAT F ALL $ $ FINISH
Rev U
- 36 -
GTTABLE
EXAMPLE 3 Table 12.3-1
GTSTRUDL Table Properties for Analysis and Steel Design Property
Description
AX
cross-section area
AY
Y axis shear area computed as the profile depth times the web thickness
AZ
Z axis shear area computed as 2/3 of the total flange area
IX
torsional moment of inertia
IY
moment of inertia about the Y axis
IZ
moment of inertia about the Z axis
RY
radius of gyration about the Y axis
RZ
radius of gyration about the Z axis
RT
radius of gyration for the flange and 1/3 of the compression web area about an axis in the plane of the web; for these shapes 1/3 of the compression web area is 1/6 of the total web area
ZY
plastic modulus about the local Y axis
ZZ
plastic modulus about the local Z axis
SY
section modulus about the Y axis
SYS
SY
SZ
section modulus about the Z axis
SZS
SZ
FLTK
flange thickness
WBTK
web thickness
YD
profile depth
YC
positive Y direction distance from the Z axis to the extreme fiber along the Y axis
ZD
flange width
ZC
the positive Z direction distance from the Y axis to the extreme fiber along the Z axis
- 37 -
Rev U
EXAMPLE 3
GTTABLE Table 12.3-1 (continued) GTSTRUDL Table Properties for Analysis and Steel Design
Property
Description
INTYD
clear depth of the web computed as the profile depth minus twice the flange thickness
BF/2TF
b/t ratio of the flange computed as ½ the flange width divided by the flange thickness
D/TW
profile depth divided by the web thickness
YD/AFL
profile depth divided by the area of one flange
EY
distance from centroid to shear center parallel to the Y axis
EZ
distance from centroid to shear center parallel to the Z axis
CW
warping constant
ND
nominal depth
WEIGHT
profile group number taken from Table 1 and 2 of the AISC ASD Manual of Steel Construction Ninth Edition
GRPNUM
profile group number taken from Table 1 and 2 of the AISC ASD Manual of Steel Construction Ninth Edition
SHAPE
a number indicating the profile shape = 1.0, W shapes = 1.1, S shapes = 1.2, HP shapes = 1.3, M shapes
Rev U
- 38 -
GTTABLE
EXAMPLE 4.1
12.4 EXAMPLE 4.1: General example to show Modify, Transfer, Change , and Delete Command (Input file only). TABLE ‘EXAMPLE’ INITIATE TABLE ‘EXSTEEL’ ADD HEADINGS ‘WEIGHT’ WEIGHT 1 LENGTH -1 ‘AX’ LENGTH 2 ‘YD’ L 1 $ DEPTH ‘IZ’ L 4 ‘IY’ L 4 ‘SZ’ L 3 UNITS INCH POUND $ ADD ITEMS ‘WEIGHT’ ‘AX’ ‘YD’ ‘IZ’ ‘IY’ ‘SZ’ ‘W14X90' 7.9167 26.5 14.02 999.0. 362.0 143.0 ‘W12X58' 4.8333 17.0 12.19 475.0 107.0 78.0 ‘W4X13' 1.0833 3.83 4.16 11.3 3.86 5.46 ‘W10X100' 8.3333 29.4 11.1 623.0 207.0 112.0 ‘W16X50' 4.1667 14.75 16.26 659.0 37.2 81.0 ‘C5X9' 0.75 2.64 5.0 8.9 0.632 3.56 FILE TABLE $ $ CHANGE THE VALUE OF AX FOR SECTION ‘W16X50’ $ WITH A NEW VALUE OF 14.70. $ MODIFY TABLE ‘EXSTEEL’ MODIFY ITEMS ‘AX’ ‘W16X50' 14.7 FILE TABLE OUTPUT TABLE ‘EXSTEEL’ ALL ORDER TABLE ‘EXSTEEL’ ORDER BY INCREASING ‘AX’ ORDER TABLE ‘EXSTEEL’ ARRANGE ‘SZ’ ON ORDERING ‘AX’ WITH ID ‘AXSZ’ FILE TABLE OUTPUT ‘EXSTEEL’ ALL TRANSFER TABLE <EXSTEEL’ TO
Rev U
EXAMPLE 4.1
GTTABLE
OUTPUT TABLE
Rev U
- 40 -
GTTABLE
EXAMPLE 4.2
12.5 EXAMPLE 4.2: INPUT and OUTPUT of EXAMPLE 4.1 TABLE ‘EXAMPLE’ INITIATE TABLE ‘EXSTEEL’ ADD HEADINGS ‘WEIGHT’ WEIGHT 1 LENGTH -1 ‘AX’ LENGTH 2 ‘YD’ L 1 $ DEPTH ‘IZ’ L 4 ‘IY’ L 4 ‘SZ’ L 3 UNITS INCH POUND ADD ITEMS ‘WEIGHT’ ‘AX’
‘YD’
‘IZ’
‘W14X90' 7.9167 26.5 14.02 999.0 ‘W12X58' 4.8333 17.0 12.19 475.0 ‘W4X13' 1.0833 3.83 4.16 11.3 ‘W10X100' 8.3333 29.4 11.1 623.0 ‘W16X50' 4.1667 14.75 16.26 659.0 ‘C5X9' 0.75 2.64 5.0 8.9 FILE TABLE $ $ CHANGE THE VALUE OF AX FOR SECTION ‘W16X50’ $ WITH A NEW VALUE OF 14.70. $ MODIFY TABLE ‘EXSTEEL’ MODIFY ITEMS ‘AX’ ‘W16X50' 14.7 FILE TABLE OUTPUT TABLE ‘EXSTEEL’ ALL
- 41 -
‘IY’ 362.0 107.0 3.86 207.0 37.2 0.632
‘SZ’ 143.0 78.0 5.46 112.0 81.0 3.56
Rev U
EXAMPLE 4.2
GTTABLE
***************************** * TABLE OUTPUT EXSTEEL * ***************************** HEADINGS WEIGHT AX YD IZ IY SZ
LB INCH INCH INCH INCH INCH
1 2 1 4 4 3
INCH
-1
TABLE DATA WEIGHT W14X90 7.916700 W12X58 4.833300 W4X13 1.083300 W10X100 8.333300 W16X50 4.166700 C5X9 0.750000
AX 26.500000 17.000000 3.820000 29.400000 14.750000 2.640000
DEPTH 14.020000 12.190000 4.160000 11.100000 16.250000 5.000000
IZ IY SZ 999.000000 362.000000 143.000000 475.000000 107.000000 78.000000 11.300000 3.860000 5.460000 623.000000 207.000000 112.000000 659.000000 37.020000 81.000000 8.900000 0.632000 3.560000
ORDER TABLE ‘EXSTEEL’ ORDER BY INCREASING ‘AX’ ORDER TABLE ‘EXSTEEL’ ARRANGE ‘SZ’ ON ORDERING ‘AX’ WITH ID ‘AXSZ’ FILE TABLE OUTPUT ‘EXSTEEL’ ALL ***************************** * TABLE OUTPUT EXSTEEL * ***************************** HEADINGS WEIGHT AX YD IZ IY SZ
Rev U
LB INCH INCH INCH INCH INCH
1 2 1 4 4 3
INCH
-1
- 42 -
GTTABLE
EXAMPLE 4.2
TABLE DATA WEIGHT 7.916700 4.833300 1.083300 8.333300 4.166700 0.750000
W14X90 W12X58 W4X13 W10X100 W16X50 C5X9
AX 26.500000 17.000000 3.820000 29.400000 14.700000 2.640000
DEPTH 14.020000 12.190000 4.160000 11.100000 16.250000 5.000000
IZ IY SZ 999.000000 362.000000 143.000000 475.000000 107.000000 78.000000 11.300000 3.860000 5.460000 623.000000 207.000000 112.000000 659.000000 37.020000 81.000000 8.900000 0.632000 3.560000
ORDERING ITEMS C5X9 W4X13 W16X50 W12X58 W14X90 W10X100
AX
--INCH 2
2.6400001 3.8300000 14.700000 17.000000 26.500000 29.400000
AXSZ
= SZ ARRANGED ON ORDERING AX
ITEMS
AXSZ
C5X9 W4X13 W16X50 W12X58 W14X90 W10X100
--INCH 4
3.560000 5.460000 81.000000 78.000000 143.000000 112.000000
TRANSFER TABLE ‘EXSTEEL’ TO ‘TRIAL’ ‘NEW’ ALL FILE TABLE OUTPUT TABLE ‘TRIAL’ ALL
- 43 -
Rev U
EXAMPLE 4.2
GTTABLE
***************************** * TABLE OUTPUT TRIAL * ***************************** HEADINGS WEIGHT AX YD IZ IY SZ
LB INCH INCH INCH INCH INCH
1 2 1 4 4 3
INCH
-1
TABLE DATA
W14X90 W12X58 W4X13 W10X100 W16X50 C5X9
WEIGHT 7.916700 4.833300 1.083300 8.333300 4.166700 0.750000
AX 26.500000 17.000000 3.820000 29.400000 14.700000 2.640000
DEPTH 14.020000 12.190000 4.160000 11.100000 16.250000 5.000000
IZ IY SZ 999.000000 362.000000 143.000000 475.000000 107.000000 78.000000 11.300000 3.860000 5.460000 623.000000 207.000000 112.000000 659.000000 37.020000 81.000000 8.900000 0.632000 3.560000
CHANGE FOR TABLE ‘TRIAL’ FROM ‘NEW’ TO ‘OLD’ THE FOR TABLE TRIAL HAS BEEN CHANGED DELETE TABLE ‘TRIAL’ ‘OLD’ DELETE ITEM ‘C5X9' FILE TABLE **** FOLLOWING MESSAGE REFERS TO PREVIOUS OPERATION BLOCK **** TABLE MESSAGE 3.2 - TABLE DELETION SUMMARY **** FOLLOWING ITEMS ARE DELETED C5X9
Rev U
- 44 -
GTTABLE
EXAMPLE 4.2
OUTPUT TABLE ‘TRIAL’ ALL ***************************** * TABLE OUTPUT TRIAL * ***************************** HEADINGS WEIGHT AX YD IZ IY SZ
LB INCH INCH INCH INCH INCH
1 2 1 4 4 3
INCH
-1
TABLE DATA
W14X90 W12X58 W4X13 W10X100 W16X50
WEIGHT 7.916700 4.833300 1.083300 8.333300 4.166700
AX 26.500000 17.000000 3.820000 29.400000 14.700000
DEPTH 14.020000 12.190000 4.160000 11.100000 16.250000
IZ IY SZ 999.000000 362.000000 143.000000 475.000000 107.000000 78.000000 11.300000 3.860000 5.460000 623.000000 207.000000 112.000000 659.000000 37.020000 81.000000
DELETE TABLE ‘EXSTEEL’ ALL DELETE TABLE ‘TRIAL’ ‘OLD’ ALL **** FOLLOWING MESSAGE REFERS TO PREVIOUS OPERATION BLOCK **** TABLE MESSAGE 3.1 - TABLE EXSTEEL IS DELETED FINISH
- 45 -
Rev U
EXAMPLE 5.1
GTTABLE
12.6 EXAMPLE 5.1: Transfer from GTSTRUDL Table to Table Example (INPUT file only) TABLE TRANSFER SUBSYSTEM TABLE ‘EXSTEEL’ TO TABLE ‘WSECT’ TRANSFER ITEMS FROM ‘W14X730’ TO ‘W14X22’ FILE TABLE DELETE TABLE ‘WSECT’ DELETE ITEMS ‘W14X605' ‘W14X455' ‘W14X287' ‘W14X219' FILE TABLE OUTPUT TABLE ‘WSECT’ PRINT ITEM NAMES OUTPUT TABLE ‘WSECT’ ALL FINISH
Rev U
- 46 -
GTTABLE
Example 5.2
12.7 EXAMPLE 5.2: INPUT and OUTPUT of EXAMPLE 5.1 TABLE TRANSFER SUBSYSTEM TABLE ‘EXSTEEL’ TO TABLE ‘WSECT’ TRANSFER ITEMS FROM ‘W14X730’ TO ‘W14X22’ FILE TABLE DELETE TABLE ‘WSECT’ DELETE ITEMS ‘W14X605' ‘W14X455’ ‘W14X287’ ‘W14X219’ FILE TABLE **** FOLLOWING MESSAGE REFERS TO PREVIOUS OPERATION BLOCK **** TABLE MESSAGE 3.2 - TABLE DELETION SUMMARY **** FOLLOWING ITEMS ARE DELETED W14X605 W14X455 W14X287 W14X219 OUTPUT TABLE ‘WSECT’ ***************************** * TABLE OUTPUT WSECT * ***************************** PRINT ITEM NAMES ITEM NAMES W14X730
W14X342
W14X202
W14X142
W14X95
W14X53
W14X665
W14X314
W14X193
W14X320
W14X87
W14X48
W14X550
W14X264
W14X184
W14X136
W14X84
W14X48
W14X500
W14X246
W14X176
W14X127
W14X78
W14X38
W14X426
W14X237
W14X167
W14X119
W14X74
W14X34
W14X398
W14X228
W14X158
W14X111
W14X68
W14X30
W14X370
W14X211
W14X150
W14X103
W14X61
W14X26
W14X22
OUTPUT TABLE <WSECT’ ALL - 47 -
Rev U
Example 5.2
GTTABLE
***************************** * TABLE OUTPUT WSECT * ***************************** HEADINGS AX INCH 2 SY INCH 3 RY INCH AY INCH 2 SZ INCH 3 RZ INCH AZ INCH 2 YD INCH 1 EY INCH IX INCH 4 ZD INCH 1 EZ INCH IY INCH 4 YC INCH 1 FLTK INCH IZ INCH 4 ZC INCH 1 WBTK INCH
1 1 1 1 1 1
YD/AFL COMP WEIGHT ZZ ZY INTYD
INCH -1
RT INCH 1 BF/2TF LB 1 INCH -1 D/TW INCH 3 GRPNUM INCH 3 SHAPE INCH 1
TABLE DATA AX SZ EY ZZ SHAPE W14X730
W12X665
W14X550
W10X500
215.000000 1280.000000 0.000000 1660.000000 1.000000 196.000000 1150.000000 0.000000 1480.000000 1.000000 162.000000 933.000000 0.000000 1180.000000 1.000000 147.000000 840.000000 0.000000 1050.000000 1.000000
Rev U
AY YD EZ ZY
AZ ZD FLTK INTYD
IX YC WBTK RT
IY ZC YD/AFL BF/2TF
IZ RY COMP D/TW
SY RZ WEIGHT GRPNUM
68.867996 117.112999 1450.000000 4720.000000 14400.000000 527.000000 22.440001 17.889000 11.220000 8.94400 4.690000 8.180000 0.000000 4.910000 3.069000 0.255000 1.000000 60.833000 816.000000 12.620000 5.270000 1.820000 7.310000 5.000000 61.238998 106.392998 1120.000000 4170.000000 12500.000000 472.000000 21.670000 17.646000 10.835000 8.823000 4.620000 7.990000 0.000000 4.522000 2.826000 0.272000 1.000000 55.417000 730.000000 12.626000 5.170000 1.950000 7.670000 5.000000 48.340000 20.260000 0.000000 584.000000
87.589996 17.205999 3.818000 12.624000
670.000000 3260.000000 10.130000 8.603000 2.386000 0.308000 5.000000 2.250000
9450.000000 378.000000 4.490000 7.640000 1.000000 45.833000 8.490000 4.000000
42.950001 19.629999 0.000000 522.000000
79.392998 17.007999 3.501000 12.628000
514.000000 2880.000000 9.815000 8.504000 2.188000 0.330000 4.920000 2.430000
8250.000000 339.000000 4.430000 7.490000 1.000000 41.667000 8.970000 4.000000
- 48 -
GTTABLE W16X426
W14X398
W16X370
W14X342
W16X314
W14X264
W16X246
W14X237
125.000000 35.043999 707.000000 18.690001 0.000000 0.000000 869.000000 434.000000 1.000000 117.000000 32.409000 657.000000 18.309999 0.000000 0.000000 802.000000 401.000000 1.000000 109.000000 29.691000 608.000000 17.940001 0.000000 0.000000 737.000000 370.000000 1.000000 101.000000 27.129999 559.000000 17.559999 0.000000 0.000000 673.000000 338.000000 1.000000 92.300003 24.323999 512.000000 17.190001 0.000000 0.000000 611.000000 307.000000 1.000000 77.5999980 19.882000 427.000000 16.500000 0.000000 0.000000 502.000000 254.000000 1.000000 72.300003 18.281000 397.000000 16.250000 0.000000 0.000000 464.000000 235.000000 1.000000 69.699997 17.570999 382.000000 16.120001 0.000000 0.000000 445.000000 225.000000 1.000000
Example 5.2 67.514000 16.695000 3.033000 12.624000
330.000000 2360.000000 9.345000 8.347000 1.875000 0.369000 4.810000 2.750000
6610.000000 283.000000 4.340000 7.260000 1.000000 35.500000 9.970000 4.000000
62.887001 16.590000 2.843000 12.624000
272.000000 2170.000000 9.155000 8.295000 1.770000 0.388000 4.760000 2.920000
6010.000000 262.000000 4.310000 7.170000 1.000000 33.167000 10.300000 4.000000
58.387001 16.475000 2.658000 12.624000
220.000000 1990.000000 8.970000 8.237000 1.655000 0.410000 4.720000 3.100000
5450.000000 241.000000 4.270000 7.080000 1.000000 30.833000 10.800000 4.000000
53.852001 16.365000 2.468000 12.624000
178.000000 1810.000000 8.780000 8.182000 1.545000 0.435000 4.680000 3.320000
4910.000000 221.000000 4.240000 6.990000 1.000000 28.500000 11.400000 4.000000
49.418999 16.235001 2.283000 12.624000
140.000000 1630.000000 8.595000 8.117000 1.415000 0.464000 4.630000 3.560000
4400.000000 201.000000 4.200000 6.900000 1.000000 26.167000 12.100000 4.000000
41.409001 16.025000 1.938000 12.624000
85.300003 1330.000000 8.250000 8.012000 1.205000 0.531000 4.540000 4.130000
3530.000000 166.000000 4.140000 6.740000 1.000000 22.000000 13.700000 4.000000
38.543999 15.945000 1.813000 12.624000
69.699997 1230.000000 8.125000 7.972000 1.125000 0.562000 4.510000 4.400000
3230.000000 154.000000 4.120000 6.680000 1.000000 20.500000 14.400000 4.000000
37.081001 15.910000 1.748000 12.624000
62.599998 1170.000000 8.060000 7.955000 1.090000 0.585000 4.500000 4.550000
3080.000000 148.000000 4.110000 6.650000 1.000000 19.750000 14.800000 4.000000
- 49 -
Rev U
Example 5.2 W16X228
W14X211
W16X202
W14X193
W16X184
W14X176
W16X167
W14X158
67.099998 368.000000 0.000000 427.000000 1.000000 62.099998 339.000000 0.000000 391.000000 1.000000 59.400002 325.000000 0.000000 373.000000 1.000000 56.700001 310.000000 0.000000 355.000000 1.000000 54.099998 296.000000 0.000000 338.000000 1.000000 51.700001 282.000000 0.000000 321.000000 1.000000 49.099998 267.000000 0.000000 303.000000 1.000000 46.500000 253.000000 0.000000 286.000000 1.000000
Rev U
GTTABLE 16.719999 16.000000 0.000000 216.000000
35.707001 15.865000 1.688000 12.624000
56.200001 1120.00000 8.000000 7.932000 1.045000 0.597000 4.480000 4.700000
2940.000000 142.000000 4.100000 6.620000 1.000000 19.000000 15.300000 4.000000
15.435000 15.750000 0.000000 198.000000
32.926998 15.800000 1.563000 12.624000
44.799999 7.875000 0.980000 4.460000
103.000000 7.900000 0.638000 5.050000
2670.000000 130.000000 4.070000 6.560000 1.000000 17.583000 16.100000 3.000000
14.536000 15.630000 0.000000 189.000000
31.563000 15.750000 1.503000 12.624000
39.599998 7.815000 0.930000 4.440000
980.000000 7.875000 0.660000 5.240000
2540.000000 124.000000 4.060000 6.540000 1.000000 16.833000 16.799999 3.000000
13.795000 15.500000 0.000000 180.000000
30.121000 15.710000 1.438000 12.624000
34.700001 7.750000 0.890000 4.420000
930.000000 7.855000 0.686000 5.460000
2400.000000 118.000000 4.050000 6.510000 1.000000 16.083000 17.400000 3.000000
12.919000 15.380000 0.000000 171.000000
28.773001 15.660000 1.378000 12.624000
30.299999 7.690000 0.840000 4.410000
883.000000 7.830000 0.713000 5.680000
2270.000000 113.000000 4.040000 6.490000 1.000000 15.333000 18.299999 3.000000
12.505000 15.250000 0.000000 163.000000
27.379999 15.640000 1.313000 12.624000
26.500000 7.625000 0.820000 4.390000
838.000000 7.820000 0.743000 5.960000
2150.000000 107.000000 4.020000 6.450000 1.000000 14.667000 18.600000 3.000000
11.794000 15.120000 0.000000 154.000000
25.958000 15.600000 1.248000 12.624000
22.799999 7.560000 0.780000 4.380000
790.000000 7.800000 0.777000 6.250000
2020.000000 101.000000 4.010000 6.420000 1.000000 13.917000 19.400000 3.000000
10.950000 15.000000 0.000000 145.000000
24.631001 15.550000 1.188000 12.624000
19.500000 7.500000 0.730000 4.360000
745.000000 7.775000 0.812000 6.540000
1900.000000 4.000000 1.000000 20.500000
- 50 -
95.800003 6.400000 13.167000 3.000000
GTTABLE W16X150
W14X142
W16X320
W14X136
W16X127
W14X119
W16X111
W14X103
44.099998 240.000000 0.000000 270.000000 1.000000 41.799999 227.000000 0.000000 255.000000 1.000000 94.099998 493.000000 0.000000 592.000000 1.000000 40.000000 216.000000 0.000000 243.000000 1.000000 37.299999 202.000000 0.000000 226.000000 1.000000 35.000000 189.000000 0.000000 211.000000 1.000000 32.700001 176.000000 0.000000 196.000000 1.000000 30.299999 164.000000 0.000000 181.000000 1.000000
Example 5.2 10.342000 14.880000 0.000000 137.000000
23.334999 15.515000 1.128000 12.624000
16.700001 7.440000 0.695000 4.350000
703.00000 7.757000 0.850000 6.880000
1790.000000 3.990000 1.000000 21.400000
90.599998 6.370000 12.500000 3.000000
10.030000 14.750000 0.000000 129.000000
21.969000 15.500000 1.063000 12.624000
14.200000 7.375000 0.680000 4.330000
660.000000 7.750000 0.895000 7.290000
1670.000000 3.970000 1.000000 21.700001
85.199997 6.320000 11.833000 3.000000
31.771000 16.809999 0.000000 304.000000
46.632000 16.709999 2.093000 12.624000
9.735000 14.750000 0.000000 117.000000
20.891001 14.740000 1.063000 12.624000
13.500000 7.375000 0.660000 4.120000
568.000000 7.370000 0.941000 6.930000
1590.000000 3.770000 1.000000 22.299999
77.000000 6.310000 11.333000 2.000000
8.918000 14.620000 0.000000 109.000000
19.547001 14.690000 0.998000 12.624000
11.100000 7.310000 0.610000 4.100000
528.000000 7.345000 0.997000 7.360000
1480.000000 3.760000 1.000000 24.000000
71.800003 6.290000 10.583000 2.000000
8.265000 14.500000 0.000000 102.000000
18.322001 14.650000 0.938000 12.624000
9.200000 7.250000 0.570000 4.080000
492.000000 7.325000 1.055000 7.810000
1370.000000 3.750000 3.000000 25.400000
67.099998 6.260000 9.917000 2.000000
7.760000 14.370000 0.000000 94.300003
17.018000 14.620000 0.873000 12.624000
7.480000 7.185000 0.540000 4.070000
455.000000 7.310000 1.126000 8.370000
1270.000000 3.730000 3.000000 26.600000
62.200001 6.230000 9.250000 2.000000
7.054000 14.250000 0.000000 87.199997
15.799000 14.575000 0.813000 12.624000
6.020000 7.125000 0.495000 4.050000
420.000000 7.287000 1.203000 8.960000
1170.000000 3.720000 2.000000 28.799999
57.599998 6.210000 8.583000 2.000000
137.000000 1640.000000 8.405000 8.355000 1.890000 0.481000 4.730000 3.990000
- 51 -
4140.000000 196.000000 4.170000 6.630000 1.000000 26.667000 8.890000 4.000000
Rev U
Example 5.2
GTTABLE
W14X95
27.900000 151.000000 0.000000 166.000000 1.000000
6.566000 14.120000 0.000000 79.900002
14.506000 14.545000 0.748000 12.624000
4.740000 7.060000 0.465000 4.040000
384.000000 7.272000 1.298000 9.720000
1060.000000 3.710000 2.000000 30.400000
52.799999 6.170000 7.917000 2.000000
W16X87
25.600000 138.000000 0.000000 151.000000 1.000000 24.700001 131.000000 0.000000 145.000000 1.000000 22.900000 121.000000 0.000000 134.000000 1.000000 21.799999 112.000000 0.000000 126.000000 1.000000 20.000000 103.000000 0.000000 115.000000 1.000000 17.900000 92.199997 0.000000 102.000000 1.000000 15.600000 77.800003 0.000000 87.099998 1.000000
5.880000 14.000000 0.000000 73.000000
13.301000 14.500000 0.688000 12.624000
3.680000 7.000000 0.420000 4.020000
350.000000 7.250000 1.403000 10.500000
967.000000 3.700000 2.000000 33.299999
48.200001 6.150000 7.250000 2.000000
6.395000 14.180000 0.000000 57.000000
12.472000 12.023000 0.778000 12.624000
4.410000 7.090000 0.451000 3.320000
225.000000 6.011000 1.516000 7.730000
928.000000 3.020000 3.000000 31.400000
37.500000 6.130000 7.000000 2.000000
6.018000 14.060000 0.000000 52.400002
11.488000 12.000000 0.718000 12.624000
3.520000 7.030000 0.428000 3.310000
207.000000 6.000000 1.632000 8.360000
851.000000 3.000000 3.000000 32.900002
34.500000 6.090000 6.500000 2.000000
6.385000 14.190000 0.000000 40.500000
10.515000 10.072000 0.783000 12.624000
3.860000 7.095000 0.450000 2.760000
133.000000 5.036000 1.799000 6.430000
797.000000 2.480000 1.000000 31.500000
26.500000 6.050000 6.167000 2.000000
5.877000 14.060000 0.000000 36.799999
9.612000 10.040000 0.718000 12.624000
3.010000 7.030000 0.418000 2.740000
121.000000 5.020000 1.950000 6.990000
724.000000 2.460000 1.000000 33.599998
24.100000 6.020000 5.667000 2.000000
5.258000 13.910000 0.000000 32.700001
8.573000 10.000000 0.643000 12.624000
2.190000 6.955000 0.378000 2.730000
107.000000 5.000000 2.163000 7.780000
641.000000 2.450000 3.000000 36.799999
21.500000 5.980000 5.083000 2.000000
5.158000 13.940000 0.000000 21.900000
7.073000 8.062000 0.658000 12.624000
1.930000 6.970000 0.370000 2.180000
57.50000 4.031000 2.628000 6.130000
542.000000 1.920000 1.000000 37.700001
14.300000 5.900000 4.417000 1.000000
W14X84
W16X78
W14X74
W16X68
W14X61
W16X53
Rev U
- 52 -
GTTABLE W14X48
W16X43
W14X38
W16X34
W14X30
W16X26
W14X22
14.100000 70.199997 0.000000 78.400002 1.000000 12.600000 62.700001 0.000000 69.699997 1.000000 11.200000 54.700001 0.000000 61.599998 1.000000 10.000000 48.599998 0.000000 54.599998 1.000000 8.830000 41.900002 0.000000 47.200001 1.000000 7.670000 35.099998 0.000000 40.000000 1.000000 6.490000 28.900000 0.000000 33.099998
Example 5.2 4.682000 13.810000 0.000000 19.600000
6.350000 8.031000 0.593000 12.624000
1.440000 6.905000 0.339000 2.160000
51.299999 4.015000 2.900000 6.770000
485.000000 1.910000 1.000000 40.700001
12.800000 5.860000 4.000000 1.000000
4.213000 13.680000 0.000000 17.299999
5.632000 8.000000 0.528000 12.624000
1.050000 6.840000 0.308000 2.140000
45.099998 4.000000 3.239000 7.580000
429.000000 1.890000 3.000000 44.400002
11.300000 5.820000 3.583000 1.000000
4.420000 14.120000 0.000000 12.100000
4.635000 6.776000 0.513000 13.094000
0.796000 7.060000 0.313000 1.800000
26.600000 3.388000 4.062000 6.600000
386.000000 1.540000 1.000000 45.099998
7.860000 5.880000 3.167000 1.000000
4.018000 14.000000 0.000000 10.600000
4.077000 6.750000 0.453000 13.094000
0.567000 7.000000 0.287000 1.780000
23.299999 3.375000 4.579000 7.450000
340.000000 1.520000 3.000000 48.799999
6.890000 5.830000 2.833000 1.000000
3.742000 13.860000 0.000000 8.950000
3.438000 6.733000 0.383000 13.094000
0.376000 6.930000 0.270000 1.750000
19.500000 3.366000 5.375000 8.790000
290.000000 1.490000 3.000000 51.299999
5.800000 5.740000 2.500000 1.000000
3.542000 13.890000 0.000000 5.520000
2.801000 5.025000 0.418000 13.054000
0.355000 6.945000 0.255000 1.290000
8.860000 2.512000 6.613000 6.010000
244.000000 1.080000 1.000000 54.500000
3.530000 5.640000 2.167000 1.000000
3.156000 13.720000 0.000000 4.390000
2.233000 5.000000 0.335000 13.050000
0.208000 6.860000 0.230000 1.260000
7.000000 2.500000 8.191000 7.460000
198.000000 1.040000 3.000000 59.700001
2.800000 5.530000 1.833000 1.000000
FINISH
- 53 -
Rev U
Example 5.2
GTTABLE
End of Document.
Rev U
- 54 -
Related Documents 171j1w
Gt Table 176d3n
December 2019 25
Gt% 30v5e
October 2020 0
Gt Questions m3i2m
November 2019 39
Gt Reading 1f162c
October 2021 0
Gt-c3313t_ug_br 8613g
September 2022 0