Ak96 Error Code 350 146g6b

Table of content C CB ......................................................................................................................................................... 1 C CC ......................................................................................................................................................... 7 C CF ....................................................................................................................................................... 13 C CO ....................................................................................................................................................... 43 C FRFF ................................................................................................................................................... 90 C Cx 000................................................................................................................................................. 91 C CSYS .................................................................................................................................................. 93 C EBUF .................................................................................................................................................. 99 C SYS ..................................................................................................................................................... 99 P ENV .................................................................................................................................................. 101 P MEM ................................................................................................................................................. 102 P PHEP ................................................................................................................................................. 102 P POW .................................................................................................................................................. 103 P PPR.................................................................................................................................................... 103 P PSYS ................................................................................................................................................. 104 P PREC ................................................................................................................................................. 105 P PTRA ................................................................................................................................................ 106 P SDT ................................................................................................................................................... 108 W WAD ............................................................................................................................................... 113 W WPR ................................................................................................................................................ 113 W WSYS .............................................................................................................................................. 114 ? UDEF................................................................................................................................................. 115

This error code list is intended for use together with AK 96, program version 3.50

HCEN12371 Rev. 10.2011 Program version 3.50

AK 96® - Error Codes

About...Arrays An array is a defined block of computer memory. It consists of elements, and the number of elements determine the array size. The elements are accessed by their index numbers. The index number is placed in parenthesis after the array name, e.g. ArrayName(99). This array consists of 100 elements (0-99):

In the AK 96, all variables of interest are placed in arrays. The array names refer to the type of variables stored in the arrary. An example: the FRI-array stores variables from the fluid control. The key to the variables: ex. FRI(FI_DEGASS$PRESS) F is source TRACO name R is RAM I is the type of the variable, in this case an integer (FI_DEGASS$PRESS) is the index in the FRI array Source TRACO names B: Blood F: Fluid O: Operator's C: Common

AK 96® - Arrays


The AK 96® Arrays


AK 96® - Arrays

C CB 003, Venous Pressure C CB 003 000

CASE ERROR Transient error General description of conditions for occurring: - Internal software error

C CB 006, Blood Pump Control C CB 006 000


C CB 006 001

ERROR DURING LOAD/READ Unconditional error, blood pump not available General description of conditions for occurring: - The blood pump timer is not working properly. Technical description of conditions for occurring: - The timer 9513 has returned error message(s). Some possible explanations why the error has occurred: - The timer IC 34 on the control driver board is broken.

C CB 006 002

ERROR DURING SET DISCRETE PORT Unconditional error, blood pump not available General description of conditions for occurring: - Internal software error

C CB 007, Art And Ven Clamp Control C CB 007 000




1 (115)

C CB 008, Blood Volume C CB 008 000


C CB 008 001


C CB 008 002

BLOOD PUMP TACHO ERROR Unconditional error, blood pump not available General description of conditions for occurring: - The blood pump tacho count-up value is incorrect Technical description of conditions for occurring: - Tacho count up value is out of limit (<0 or >20000) Some possible explanations why the error has occurred: - The timer IC 34 on the control driver board is broken

2 (115)



C CB 009, Blood Flow C CB 009 000


C CB 009 001


C CB 009 002

DELTA TIME ERROR Unconditional error, blood pump not available General description of conditions for occurring: - Timing error. Technical description of conditions for occurring: - The time between the two last blood flow measurements was out of range. Some possible explanations why the error has occurred: - Internal software error. - The timer IC 34 on the control driver board is broken.

C CB 009 003

NUMBER OF TACHO PULSES ERROR Unconditional error, blood pump not available General description of conditions for occurring: The number of counted blood pump tacho pulses is incorrect. Technical description of conditions for occurring: Either 0 or more than 10000 tacho pulses have been counted since the last time the blood flow was measured Some possible explanations why the error has occurred: - No connection between tacho and BM I/O board - Blood pump error (blood pump stopped) - The timer IC 34 on the control driver board is broken.

C CB 009 004

MEASURED BLOOD FLOW OUT OF LIMITS Unconditional error, blood pump not available General description of conditions for occurring: - The measured blood flow has differed too much from the blood flow set value. Technical description of conditions for occurring: - BRI(BI_BloodFlActSet) - BRI(BI_BloodFl) < -600 or BRI(BI_BloodFlActSet) - BRI(BI_BloodFl) > 600



3 (115)

Some possible explanations why the error has occurred: - The blood pump unit is broken - The BM I/O board is broken (Q1-Q4 and components) - The timer IC 34 on the control driver board is broken.

C CB 010, Heparin Pump C CB 010 000


C CB 010 001

ERROR DURING LOAD/READ Conditional error, confirm by zero-set heparin flow General description of conditions for occurring: - The heparin pump timer is not working properly Technical description of conditions for occurring: - The timer 9513 has returned error message(s). Some possible explanations why the error has occurred: - The timer IC 34 on the control driver board is broken.

C CB 010 002

ESTIMATED AND MEASURED HEPARIN VOL. DIFFER TOO MUCH Conditional error, confirm by zero-set heparin flow General description of conditions for occurring - The measured accumulated heparin volume differ more than 2 ml from the estimated accumulated volume. Technical description of conditions for occurring: - BRI(BI_MeasVol)-BRI(BI_EstAcc)<=-2 or (BRI(BI_MeasVol)-BRI(BI_EstAcc)>=2 Some possible explanations why the error has occurred: - The heparin pump encoder is broken - The heparin pump belt is broken - Bad connection between heparin pump encoder and BM I/O board - IC 5 on BM I/O board broken - IC 48 on protective U board broken - IC 29 or IC 34 on control driver board broken

C CB 010 003

ESTIMATED AND MEASURED HEPARIN BOLUS VOL. DIFFER TOO MUCH Conditional error, confirm by setting bolus volume and heparin flow rate to zero. General description of conditions for occurring - The estimated and measured bolus heparin volume in the control system differ more than ±10%.

4 (115)



C CB 011, Stroke Volume C CB 011 000


C CB 011 001


C CB 011 002

NUMBER OF BLOOD PUMP TACHO PULSES ERROR Unconditional error, blood pump not available General description of conditions for occurring: - The blood pump tacho count-up value is incorrect Technical description of conditions for occurring: - Tacho count up value is out of limit (<0 or >20000) Some possible explanations why the error has occurred: - The timer IC 34 on the control driver board is broken

C CB 014, Single Needle Time Control C CB 014 000


C CB 014 001

ARTERIAL PHASE TIME OUT OF LIMITS ERROR Unconditional error, blood pump not available General description of conditions for occurring: - Internal software error

C CB 014 002

VENOUS PHASE TIME OUT OF LIMITS ERROR. Unconditional error, blood pump not available General description of conditions for occurring: - Internal software error

C CB 015, Auto Rinse Back C CB 015 000




5 (115)

C CB 016, Auto Priming C CB 016 000


C CB 017, Blood Pressure Meter C CB 017 000


C CB 017 001

ERROR RECEIVED FROM BPM Unconditional error General description of conditions for occurring: - Internal software error

6 (115)



C CC 002, Preset Variable Storage C CC 002 000


C CC 002 001

DEFAULT PRESET ERROR Unconditional error, blood pump not available General description of conditions for occurring: - The new variables could not be set to default values after a program change Some possible explanations why the error has occurred: - Internal software error

C CC 002 002

PRESET VARIABLE CHECKSUM ERROR (INIT) Unconditional error, blood pump not available General description of conditions for occurring: -The preset variable checksum was incorrect during init (start-up) phase. Make a default preset. Some possible explanations why the error has occurred: - Internal software error - Broken safe-RAM (battery-RAM)

C CC 002 003

PRESET VARIABLE CALCULATION ERROR Unconditional error, blood pump not available General description of conditions for occurring: - During start-up was detected that the preset variables need to be recalculated. Make a default preset, or use external preset to represet the machine Technical description of conditions for occurring: - EL(EEL_PrsMustCalculate)=TRUE Some possible explanations why the error has occurred: - The preset write phase was aborted (external preset) - The preset calculation phase was aborted (external preset)

C CC 002 006

PRESET VARIABLE CHECKSUM ERROR Unconditional error, blood pump not available General description of conditions for occurring: -The preset variable checksum was incorrect after init phase. If C CC 002 002 has occurred during init, then C CC 002 006 will also occur, following init. Some possible explanations why the error has occurred: - Internal software error - Broken safe-RAM (battery-RAM)



7 (115)

C CC 004, MM95 A/D Conversion C CC 004 000


C CC 004 001

SET DISCRETE PORT ERROR Unconditional error, blood pump not available General description of conditions for occurring: - Internal software error

C CC 004 002

MM95 A/D CONVERTER BUFFER POINTER ERROR Unconditional error, blood pump not available General description of conditions for occurring: - The MM95 A/D converter interrupt function puts data in a buffer and increments an input pointer. The MM95 A/D converter function fetches data from that buffer and increments an output pointer. One of these pointers had an incorrect value. Some possible explanations why the error has occurred: - The timer IC21 on control U board is broken - RAM error

C CC 004 003

MM95 A/D CONVERTER OFFSET ERROR Unconditional error, blood pump not available General description of conditions for occurring: - The zero voltage value was outside limits Some possible explanations why the error has occurred: - A/D converter IC 9 on MM I/O board is broken - No connection between MM I/O board and control U board (signal CADFQ)

C CC 004 004

MM95 A/D CONVERTER REFERENCE ERROR Unconditional error, blood pump not available General description of conditions for occurring: - The reference voltage value was outside limits Some possible explanations why the error has occurred: - A/D converter IC 9 on MM I/O board is uncalibrated - A/D converter IC 9 on MM I/O board is broken - No connection between MM I/O board and control U board (signal CADFQ)

C CC 004 005

MM95 TIMER ERROR Unconditional error, blood pump not available General description of conditions for occurring: - The MM95 timer is not working properly. Technical description of conditions for occurring: - The timer 9513 has returned error message(s). Some possible explanations why the error has occurred:

8 (115)



- The timer IC 21 on the control U board is broken.

C CC 005, Analog Connection Check C CC 005 000


C CC 005 001

SET DISCRETE PORT ERROR Unconditional error, blood pump not available General description of conditions for occurring: - Internal software error

C CC 006, Monitor Board Temperature CC 006 000


CC 006 001

MONITOR TEMPERATURE TOO HIGH. Unconditional error, blood pump not available General description of conditions for occurring: The temperature inside the monitor is above 60 degree C Technical description of conditions for occurring: BRI(BI_MonitorTemp) >60 degree C Some possible explanations why the error has occurred: - The fan has stopped - Dirty air filter

C CC 007, Data Recovery C CC 007 000


C CC 008, Transducer Parameter Init C CC 008 001

ERROR READING PARAMETERS FROM UF CELL Unconditional error, blood pump not available General description of conditions for occurring: - An error occurred while reading transducer parameters during init (start-up). Some possible explanations why the error has occurred: - No connection between UF cell and control driver board (P402). - Incorrect transducer ID. Update transducer ID (I2C scan). - UF cell EEPROM broken - Serial bus error on control U board, or I/O SIMM problem



9 (115)

(P310) C CC 008 100

ERROR READING PARAMETERS FROM REG. TEMP. Unconditional error, blood pump not available General description of conditions for occurring: - An error occurred while reading transducer parameters during init (start-up). Some possible explanations why the error has occurred: - No connection between transducer board and FM I/O board - No connection between FM I/O board and control driver board - Transducer board mounted in incorrect position on FM I/O board - Incorrect transducer ID. Update transducer ID (I2C scan). - EEPROM on transducer board is broken - Serial bus error on control U board, or I/O SIMM problem (P310) - Uncalibrated transducer. Calibrate transducer - Broken FM I/O board

C CC 008 101

ERROR READING PARAMETERS FROM REG. TEMP. (HEAT) Unconditional error, blood pump not available General description of conditions for occurring: - An error occurred while reading transducer parameters during init (start-up). Some possible explanations why the error has occurred: - Refer to error description for C CC 008 100

C CC 008 102

ERROR READING PARAMETERS FROM DEGASS PRESSURE Unconditional error, blood pump not available General description of conditions for occurring: - An error occurred while reading transducer parameters during init (start-up). Some possible explanations why the error has occurred: - Refer to error description for C CC 008 100

C CC 008 103

ERROR READING PARAMETERS FOR HIGH PRESSURE GUARD Unconditional error, blood pump not available General description of conditions for occurring: - An error occurred while reading transducer parameters during init (start-up). Some possible explanations why the error has occurred: - Refer to error description for C CC 008 100

C CC 008 104

ERROR READING PARAMETERS FOR COND A TEMP. Unconditional error, blood pump not available General description of conditions for occurring: - An error occurred while reading transducer parameters during init (start-up). Some possible explanations why the error has occurred: - No connection between transducer and MM95 I/O board

10 (115)



- Incorrect connection between transducer and MM95 I/O board - No connection between MM95 I/O and control U board - Incorrect transducer ID. Update transducer ID (I2C scan). - EEPROM on transducer board is broken - Serial bus error on control U board, or I/O SIMM problem (P310) - Uncalibrated transducer. Calibrate transducer - Broken MM95 I/O board C CC 008 105

ERROR READING PARAMETERS FOR COND A TEMP. (HEAT) Unconditional error, blood pump not available General description of conditions for occurring: - An error occurred while reading transducer parameters during init (start-up). Some possible explanations why the error has occurred: - Refer to error description for C CC 008 104

C CC 008 106

ERROR READING PARAMETERS FOR COND A Unconditional error, blood pump not available General description of conditions for occurring: - An error occurred while reading transducer parameters during init (start-up). Some possible explanations why the error has occurred: - Refer to error description for C CC 008 104

C CC 008 107

ERROR READING PARAMETERS FOR COND B TEMP. Unconditional error, blood pump not available General description of conditions for occurring: - An error occurred while reading transducer parameters during init (start-up). Some possible explanations why the error has occurred: - Refer to error description for C CC 008 104

C CC 008 108

ERROR READING PARAMETERS FOR COND B TEMP. (HEAT) Unconditional error, blood pump not available General description of conditions for occurring: - An error occurred while reading transducer parameters during init (start-up). Some possible explanations why the error has occurred: - Refer to error description for C CC 008 104

C CC 008 109

ERROR READING PARAMETERS FOR COND B Unconditional error, blood pump not available General description of conditions for occurring: - An error occurred while reading transducer parameters during init (start-up). Some possible explanations why the error has occurred: - Refer to error description for C CC 008 104

C CC 008 110


ERROR READING PARAMETERS FOR MM95 A/D REF


11 (115)

Unconditional error, blood pump not available General description of conditions for occurring: - An error occurred while reading transducer parameters during init (start-up). Some possible explanations why the error has occurred: - No connection between MM95 I/O and control U board - Incorrect transducer ID. Update transducer ID (I2C scan). - EEPROM on transducer board is broken - Serial bus error on control U board, or I/O SIMM problem (P310) - Uncalibrated transducer. Calibrate transducer - Broken MM95 I/O board C CC 008 111

ERROR READING PARAMETERS FOR VENOUS PRESSURE Unconditional error, blood pump not available General description of conditions for occurring: - An error occurred while reading transducer parameters during init (start-up). Some possible explanations why the error has occurred: - No connection between transducer board and BM I/O board - No connection between BM I/O board and control driver board - Transducer board mounted in incorrect position on BM I/O board - Incorrect transducer ID. Update transducer ID (I2C scan). - EEPROM on transducer board is broken - Serial bus error on control U board, or I/O SIMM problem (P310 - Uncalibrated transducer. Calibrate transducer - Broken BM I/O board

C CC 010, A/D Conversion C CC 010 000


C CC 010 001

A/D CONVERTER BUFFER POINTER ERROR Unconditional error, blood pump not available General description of conditions for occurring: - Data have not been read from A/D converter (IC 20) on the control driver board. Technical description of conditions for occurring: - The A/D converter interrupt function should have stored A/D converter data in a buffer and should have changed the value of adInPtr to a value that is not the same as adOutPtr. The A/D converter interrupt routine had not executed. Some possible explanations why the error has occurred - The A/D converter IC 20 on the control driver is broken - The PAL IC 28 on the control U board is broken - The inverter IC 4 on the control driver board is broken - The interrupt controller IC 52 on the control U board is broken (N.E.: the U IC 10 on control U board is broken)

12 (115)



C CC 010 002

AK 96 A/D CONVERTER OFFSET ERROR Unconditional error, blood pump not available General description of conditions for occurring: - The zero voltage value was outside limits Some possible explanations why the error has occurred: - A/D converter IC 20 on control driver board is broken

C CC 010 003

AK 96 A/D CONVERTER REFERENCE ERROR Unconditional error, blood pump not available General description of conditions for occurring: - The reference voltage value was outside limits Some possible explanations why the error has occurred: - A/D converter IC 20 on control driver board is uncalibrated - A/D converter IC 20 on control driver board is broken

C CC 010 004

AK 96 AD REFERENCE VOLTAGE INIT ERROR Unconditional error, blood pump not available General description of conditions for occurring: - The U C A/D converter reference value was corrupt Some possible explanations why the error has occurred: - This error will show up on first start with new safe-RAM. Calibrate A/D converter and restart AK 96.

C CF 031 001

BICART HOLDER PRESET ERROR General description of conditions for occurring: BiCart holder is preset "Not Inst" and should be detected as closed but it is detected open. Some possible explanations why the error has occurred: Check preset for BiCart holder

C CF 001, Inlet Valve C CF 001 000


C CF 002, Direct Valve C CF 002 000




13 (115)

C CF 003, Disinfection/Rinse Valves C CF 003 000


14 (115)



C CF 004, Taration Valve C CF 004 000


C CF 005, Dia connector sensor C CF 005 001

DIA CONNECTOR SENSORS ERROR IN SAGS TEST (SENSORS TEST) General description of conditions for occurring: - Dia connector sensors are not working properly. Technical description of conditions for occurring: - During the dia connector sensors test the operator was asked to remove from or attach the connectors to the safety by block 3 times. After operator’s confirmation about the removing or attaching the dia connectors, no confirmation about it from dia connector sensors had come. Some possible explanations why the error has occurred: - IC 28 board K16646 may be broken. - The mechanical dia connector sensors may be stucked.

C CF 006, High Pressure Guard Transducer C CF, 006 000


C CFD 006 001

HIGH PRESSURE DURING SAGS TEST Unconditional error, blood pump available General description of conditions for occurring: - High pressure in monitor during SAGS test. Main flow through RIVA. Technical description of conditions for occurring: - FRI(FI_HPGPr)>450mmHg for more than 5 seconds Some possible explanations why the error has occurred: - RIVA unable to open - Fluid path obstruction - HPG broken/uncalibrated

C CFF 006 002

HIGH PRESSURE DURING FUNCTION CHECK Unconditional error, blood pump available General description of conditions for occurring: - High pressure in monitor during function check Technical description of conditions for occurring: - FRI(FI_HPGPr)>450mmHg for more than 1,5 seconds



15 (115)

Some possible explanations why the error has occurred: - Fluid path obstruction - HPG broken/uncalibrated C CFF 006 003

UNSTABLE DEGASSING PRESSURE Unconditional error, blood pump available General description of conditions for occurring: - Unstable degassing pressure during function check. The degassing pressure has been measured twice with an interval of 15 seconds. The difference between the two measurements was more than 20mmHg Technical description of conditions for occurring: - oldDegassPr - FRI(FI_DegassPr) ) < -20mmHg - oldDegassPr - FRI(FI_DegassPr) ) > 20mmHg Some possible explanations why the error has occurred: - Leakage on top of degassing chamber. Check the o-ring - Unstable/broken degassing transducer - RIVA leakage

C CFF 006 004

TOO BIG DIFFERENCE BETWEEN HPG AND DEGASS PRESSURE Unconditional error, blood pump available General description of conditions for occurring: - The difference between HPG and degassing pressure has been too big during function check of degassing transducer. Technical description of conditions for occurring: - FRI(FI_HPGPr) - FRI(FI_DegassPr) <-30mmHg or - FRI(FI_HPGPr) - FRI(FI_DegassPr) >10mmHg Some possible explanations why the error has occurred: - Uncalibrated/broken degassing pressure transducer

16 (115)



C CF 007, Heater Enable C CF 007 000


C CF 007 001

HEATER SWITCH OFF ERROR Unconditional error, blood pump available General description of conditions for occurring: - Internal software error

C CF 007 002

HEATER SWITCH ON ERROR Unconditional error, blood pump available General description of conditions for occurring: - Internal software error

C CFD 008, Heater Regulator, Disinfection/Rinse mode C CFD 008 000


C CFF 008, Heater Regulator, Function Check C CFF 008 000


C CFM 008, Heater Regulator C CFM 008 000


C CFM 008 001

FAIL TO INITIATE HEATER TIMER Unconditional error, blood pump available General description of conditions for occurring: - The heater timer is not working properly. Technical description of conditions for occurring: - The timer 9513 has returned error message(s). Some possible explanations why the error has occurred: - The timer IC 21 on the control U board is broken.

C CFM 008 002


FAILED TO LOAD HEATER TIMER Unconditional error, blood pump available


17 (115)

General description of conditions for occurring: - The heater timer is not working properly. Technical description of conditions for occurring: - The timer 9513 has returned error message(s). Some possible explanations why the error has occurred: - The timer IC 21 on the control U board is broken. C CFM 008 006

HEATER EFFICIENCY CHECK ERROR Unconditional error, blood pump available General description of conditions for occurring: - Internal software error

C CFM 008 007

REGULATOR TEMP SUPERVISION ERROR Unconditional error, blood pump available General description of conditions for occurring: - Regulator temperature differ too much from temp. in conductivity cell A. Technical description of conditions for occurring: - FRI(FI_RegTemp) < 2 degree C and FRI(FI_MM90CondTempA) > 10 degree C (for more than 4 seconds) Some possible explanations why the error has occurred: - No connection between regulator temp. board and FM I/O board - Broken regulator temp. transducer

C CFS 008, Heater Regulator, Service Mode C CFS 008 000


C CFT 008, Heater Regulator, Treatment Mode C CFT 008 000


C CFD 009, Flow Pump Regulator, Disinfection Mode C CFD 009 000


18 (115)



C CFF 009, Flow Pump Regulator, Function Check C CFF 009 000


C CFF 009 001

FLOW PUMP CURRENT ERROR Unconditional error, blood pump available General description of conditions for occurring: - Flow pump current too low Technical description of conditions for occurring: - FRI(FI_FlowPumpCurrent) < 50mA Some possible explanations why the error has occurred: - Air in flow pump - Broken/unconnected flow pump - The flow pump is decoupled. FRL(F_FlowPumpDecoupl)=TRUE ( The flow pump could not follow the flow pump motor rotation. The magnetic coupling disconnected the pump from the motor. The pump might be dirty or the flow path might be blocked). - Broken control driver board (IC24, L2, Q1 and components) - Broken control U board (IC32) (N.E.: Broken control U board, IC10)

C CFF 009 002

DEGASS PRESSURE CONTROL ERROR Unconditional error, blood pump available General description of conditions for occurring: - The flow pump could not create the preset degassing pressure Technical description of conditions for occurring: - FRI(FI_DegassPr) + EI(EEI_DegassPr) < -60mmHg or FRI(FI_DegassPr) + EI(EEI_DegassPr) > 60mmHg Some possible explanations why the error has occurred: - DRVA leakage - Flow pump/motor broken - The preset degassing pressure is too low - The degassing pressure transducer is broken - Broken control driver board (IC24, L2, Q1 and components) - Broken control U board (IC32) (N.E.: Broken control U board, IC10)



19 (115)

C CFM 009, Flow Pump Regulator C CFM 009 000


C CFM 009 001

FLOW PUMP CURRENT ERROR Unconditional error, blood pump available General description of conditions for occurring: - Flow pump current too high Technical description of conditions for occurring: - FRI(FI_FlowPumpCurren) > 1500mA Some possible explanations why the error has occurred: - Pump motor broken - Broken control driver board (R10, R11, R13, C20) - Broken control driver board A/D system (IC17, IC18, IC20 and components)

C CFS 009, Flow Pump Regulator, Service Mode C CFS 009 000


C CFS 009 001

FLOW PUMP CURRENT ERROR Unconditional error, blood pump available General description of conditions for occurring: - Flow pump current too low Technical description of conditions for occurring: - FRI(FI_FlowPumpCurrent) < 50mA Some possible explanations why the error has occurred: - Air in flow pump - Broken/unconnected flow pump - The flow pump is decoupled. FRL(F_FlowPumpDecoupl)=TRUE ( The flow pump could not follow the flow pump motor rotation. The magnetic coupling disconnected the pump from the motor. The pump might be dirty or the flow path might be blocked). - Broken control driver board (IC24, L2, Q1 and components) - Broken control U board (IC32) (N.E.: Broken control U board, IC10)

C CFS 009 002

DEGASS PRESSURE CONTROL ERROR Unconditional error, blood pump available General description of conditions for occurring: - The flow pump could not create the preset degassing pressure Technical description of conditions for occurring: - FRI(FI_DegassPr) > -(EI(EEI_DegassPr)-60)mmHg

20 (115)



Some possible explanations why the error has occurred: - DRVA leakage - Flow pump/motor broken - The preset degassing pressure is too low - The degassing pressure transducer is broken - Broken control driver board (IC24, L2, Q1 and components) - Broken control U board (IC32) (N.E.: Broken control U board, IC10) C CFS 009 004

UNSTABLE MAIN FLOW Unconditional error, blood pump available General description of conditions for occurring: - Unstable main flow during UF cell calibration Technical description of conditions for occurring: - The main flow has been outside limit (+/- 5ml/min) Some possible explanations why the error has occurred: - Broken UF cell - Leakage in fluid path - Air in fluid path - The flow pump is decoupled. FRL(F_FlowPumpDecoupl)=TRUE ( The flow pump could not follow the flow pump motor rotation. The magnetic coupling disconnected the pump from the motor. The pump might be dirty or the flow path might be blocked). - Broken control driver board (IC24, L2, Q1 and components) - Broken control U board (IC32) (N.E.: Broken control U board, IC10)

C CFT 009, Flow Pump Regulator, Treatment Mode C CFT 009 000


C CFT 009 001

DEGASS PRESSURE CONTROL ERROR Unconditional error, blood pump available General description of conditions for occurring: - The flow pump could not create the preset degassing pressure Technical description of conditions for occurring: - FRI(FI_DegassPr) > -(EI(EEI_DegassPr)-60)mmHg Some possible explanations why the error has occurred: - DRVA leakage - Flow pump/motor broken - The preset degassing pressure is too low - The degassing pressure transducer is broken - Broken control driver board (IC24, L2, Q1 and components) - Broken control U board (IC32) (N.E.: Broken control U board, IC10)

C CFT 009 002


FLOW PUMP CURRENT ERROR Unconditional error, blood pump available


21 (115)

General description of conditions for occurring: - Flow pump current too low Technical description of conditions for occurring: - FRI(FI_FlowPumpCurrent) < 50mA Some possible explanations why the error has occurred: - Air in flow pump - Broken/unconnected flow pump - The flow pump is decoupled. FRL(F_FlowPumpDecoupl)=TRUE ( The flow pump could not follow the flow pump motor rotation. The magnetic coupling disconnected the pump from the motor. The pump might be dirty or the flow path might be blocked). - Broken control driver board (IC24, L2, Q1 and components) - Broken control U board (IC32) (N.E.: Broken control U board, IC10)

C CF 010, Overheat Supervision C CF 010 000


C CFD 014, Suction Pump Regulator, Disinfection Mode C CFD 014 000


C CFF 014, Suction Pump Regulator, Function Check C CFF 014 000


22 (115)



C CFM 014, Suction Pump Regulator C CFM 014 000


C CFM 014 001

SUCTION PUMP CURRENT ERROR Unconditional error, blood pump available General description of conditions for occurring: - Suction pump current too high Technical description of conditions for occurring: FRI(FI_SuumpCurrent) > 1500mA Some possible explanations why the error has occurred: - Pump motor broken - Broken control driver board (R14, R15, R16, C24) - Broken control driver board A/D system (IC17, IC18, IC20 and components)

C CFS 014, Suction Pump Control, Service Mode C CFS 014 000


C CFT 014, Suction Pump Control, Treatment Mode C CFT 014 000




23 (115)

C CFD 018, Valve Current Measuring, Disinfection Mode C CFD 018 001

CURRENT TEST ERROR, DRVA VALVE Unconditional error, blood pump available General description of conditions for occurring: - The current through the DRVA valve has been measured with valve closed and then with valve opened. The current difference has not been large enough. Technical description of conditions for occurring: - FRI(FI_ValvesCurrent) - refCurrent < 200mA Some possible explanations why the error has occurred: - Broken/unconnected magnet on DRVA valve - Broken control driver board (Q4, V3) - DRVA is not connected and the preset “Set flow installed” is set to “not installed”.

C CFD 018 009

CURRENT TEST ERROR, DRVA VALVE Unconditional error, blood pump available General description of conditions for occurring: - The current through the DRVA valve has been measured with valve closed and then with valve opened. The current difference is too big Technical description of conditions for occurring: - FRI(FI_ValvesCurrent) - refCurrent > 200mA Some possible explanations why the error has occurred: - Broken control driver board - DRVA is connected and the preset “Set flow installed” is set to “installed”.

C CFD 018 010

CURRENT TEST ERROR, CBVA VALVE Unconditional error, blood pump available General description of conditions for occurring: - The current through CBVA valve has been measured with valve closed and then with valve opened. The current difference has not been large enough. - Broken/unconnected magnet on CBVA valve.

C CFF 018, Valve Current Measuring, Function Check C CFF 018 002

CURRENT TEST ERROR, AIVA VALVE Unconditional error, blood pump available General description of conditions for occurring: - The current through the AIVA valve has been measured with valve closed and then with valve opened. The current difference has not been large enough. Technical description of conditions for occurring: - FRI(FI_ValvesCurrent) - refCurrent < 200mA Some possible explanations why the error has occurred: - Broken/unconnected magnet on AIVA valve - Broken control driver board (Q2, V2)

C CFF 018 004

24 (115)

BUBBLE CHAMBER (DEAIRATING CHAMBER) ERROR Unconditional error, blood pump available



General description of conditions for occurring: - AIVA and REVA opened. Suction pump active and fluid tubes connected to safety by. Low level in bubble chamber is not achieved within 90 sec. The status from level sensor indicates high level in chamber Technical description of conditions for occurring: - PRL(P_BubbleTrapHigh)=TRUE Some possible explanations why the error has occurred: - The AIVA or REVA could not be opened - Broken float in bubble chamber - Broken protective driver board (IC28) C CFF 018 005

BUBBLE CHAMBER (DEAIRATING CHAMBER) ERROR Unconditional error, blood pump available General description of conditions for occurring: - AIVA and REVA opened. Suction pump active and fluid tubes connected to safety by. Low level in bubble chamber is not achieved within 90 sec. The status from level sensor indicates middle level in chamber. Technical description of conditions for occurring: - PRL(P_BubbleTrapHigh)=FALSE Some possible explanations why the error has occurred: - The AIVA or REVA could not be opened - Broken float in bubble chamber - Broken protective driver board (IC28)

C CFF 018 006

NOT POSIBLE TO REGULATE HPG PRESSURE Unconditional error, blood pump available General description of conditions for occurring: - Impossible to regulate HPG to -100mmHg in AIVA test (120 sec. test-time) Technical description of conditions for occurring: - FRI(FI_HPGPR) could not be regulated to -100mmHg Some possible explanations why the error has occurred: - Air in fluid path - Broken suction pump - Broken control U board (IC4, IC5, Q12 and components)

C CFF 018 007

CURRENT TEST ERROR , FIVA VALVE (1) Unconditional error, blood pump available General description of conditions for occurring: - The current through FIVA valve has been measured with valve closed and then with valve opened, despite the UFD has been preseted NotInst. The current difference has been large enough in order to detect that FIVA valve is installed Technical description of conditions for occurring: - FRI(FI_ValvesCurrent)-refCurrent > 200mA and not EL(EEL_UfdInstalled). Some possible explanations why the error has occurred:



25 (115)

- The UFD has been preseted NotInst instead of Inst, despite the FIVA valve and consequently the UFD is installed C CFF 018 008

CURRENT TEST ERROR , FIVA VALVE (2) Unconditional error, blood pump available General description of conditions for occurring: - The current through FIVA valve has been measured with valve closed and then with valve opened, with the UFD preseted Inst. The current difference has not been large enough. Technical description of conditions for occurring: - FRI(FI_ValvesCurrent)-refCurrent < 200mA and EL(EEL_UfdInstalled). Some possible explanations why the error has occurred: - Broken/unconnected magnet on FIVA valve. - Broken control driver board (Q10, V12). - The UFD has been preseted Inst instead of NotInst, despite there is no FIVA valve and consequently no UFD installed

C CFF 018 011

CURRENT TEST ERROR, FLVA VALVE Unconditional error, blood pump available General description of conditions for occurring: - The current through FLVA valve has been measured with valve closed and then with valve opened. The current difference has not been large enough. - Broken/unconnected magnet on FLVA valve.

C CFT 018, Valve Current Measuring, Function Check C CF 018 000


C CFT 018 001

CURRENT TEST ERROR, DRVA VALVE Unconditional error, blood pump available General description of conditions for occurring: - The current through the DRVA valve has been measured with valve closed and then with valve opened. The current difference has not been large enough. - This error code is not used in program version 3.00 and later Technical description of conditions for occurring: - FRI(FI_ValvesCurrent) - refCurrent < 200mA Some possible explanations why the error has occurred: - Broken/unconnected magnet on DRVA valve - Broken control driver board (Q4, V3)

C CFT 018 002

CURRENT TEST ERROR, AIVA VALVE Unconditional error, blood pump available General description of conditions for occurring: - The current through the AIVA valve has been measured with valve closed and then with valve opened. The current difference has not been large enough.

26 (115)



- This error code is not used in program version 3.00 and later Technical description of conditions for occurring: - FRI(FI_ValvesCurrent) - refCurrent < 200mA Some possible explanations why the error has occurred: - Broken/unconnected magnet on AIVA valve - Broken control driver board (Q2, V2) C CFT 018 003

BUBBLE CHAMBER (DEAIRATING CHAMBER) ERROR Unconditional error, blood pump available General description of conditions for occurring: - AIVA and REVA opened. Suction pump active and fluid tubes connected to safety by. Low level in bubble chamber is not achieved within 90 sec. NOTE: This error code is not used in programs later than version P2.04. Technical description of conditions for occurring: - PRL(P_BubbleTrapLow)=FALSE after 90 seconds Some possible explanations why the error has occurred: - The AIVA or REVA could not be opened - Broken float in bubble chamber - Broken protective driver board (IC28)

C CFD 020, Flow Meter, Disinfection Mode C CFD 020 000


C CFF 020, Flow Meter, Function Check C CFF 020 000


C CFM 020, Flow Meter C CFM 020 000


C CFM 020 002

UF TIMER ERROR Unconditional error, blood pump available General description of conditions for occurring: - The UF timer is not working properly. Technical description of conditions for occurring: - The timer 9513 has returned error message(s).



27 (115)

Some possible explanations why the error has occurred: - The timer IC 34 on the control driver board is broken. C CFM 020 003

VFC CHANNEL 1 PULSE COUNTER OVERFLOW Unconditional error, blood pump available General description of conditions for occurring: - The pulse counter for VFC channel 1 has counted up to its max. value Some possible explanations why the error has occurred: - The VFC, (voltage to frequency) IC 14 on control driver board, or some component around it, is broken.

C CFM 020 004

VFC CHANNEL 2 PULSE COUNTER OVERFLOW Unconditional error, blood pump available General description of conditions for occurring: - The pulse counter for VFC channel 2 has counted up to its max. value Some possible explanations why the error has occurred: - The VFC, (voltage to frequency) IC 15 on control driver board, or some component around it is broken

C CFM 020 005

UF TIMER ERROR Unconditional error, blood pump available General description of conditions for occurring: - The UF timer is not working properly. Technical description of conditions for occurring: - The timer 9513 has returned error message(s). Some possible explanations why the error has occurred: - The timer IC 34 on the control driver board is broken.

C CFM 020 006

VFC CHANNEL 1 REFERENCE MEASUREMENT ERROR Unconditional error, blood pump available General description of conditions for occurring: - The VFC channel 1 has been connected to the reference voltage. The pulse counter (IC23 counter 3, control driver board) has measured a frequency that differs too much from the frequency that usually is measured when the reference voltage is connected. Technical description of conditions for occurring: VFC1.VALUE > 0.86241*VFC1.OFFSET for 2s or VFC1.VALUE < 0.82859*VFC1.OFFSET for 2s VFC1.OFFSET = VFC value when 0V is connected. Some possible explanations why the error has occurred: - The VFC, (voltage to frequency) IC 14 on control driver board, or some component around it is broken - IC 23 broken (control driver board)

C CFM 020 007

28 (115)

VFC CHANNEL 2 REFERENCE MEASUREMENT ERROR Unconditional error, blood pump available



General description of conditions for occurring: - The VFC channel 2 has been connected to the reference voltage. The pulse counter (IC23 counter 4, control driver board) has measured a frequency that differs too much from the frequency that usually is measured when the reference voltage is connected. Technical description of conditions for occurring: VFC2.VALUE > 0.86241*VFC2.OFFSET for 2s or VFC2.VALUE < 0.82859*VFC2.OFFSET for 2s VFC2.OFFSET = VFC value when 0V is connected. Some possible explanations why the error has occurred: - The VFC, (voltage to frequency) IC 15 on control driver board, or some component around it is broken - IC 23 broken (control driver board) C CFM 020 008

VFC CHANNEL 1 OFFSET MEASUREMENT ERROR Unconditional error, blood pump available General description of conditions for occurring: - The VFC channel 1 has been connected to 0V. The pulse counter has measured a frequency that differs too much from the frequency that usually is measured when 0V is connected. Technical description of conditions for occurring: VFC1.VALUE has been outside the allowed interval 6907-10907 for 2s Some possible explanations why the error has occurred: - The VFC, (voltage to frequency) IC 14 on control driver board, or some component around it is broken - IC 23 broken (control driver board)

C CFM 020 009

VFC CHANNEL 2 OFFSET MEASUREMENT ERROR Unconditional error, blood pump available General description of conditions for occurring: - The VFC channel 2 has been connected to 0V. The pulse counter has measured a frequency that differs too much from the frequency that usually is measured when 0V is connected. Technical description of conditions for occurring: VFC2.VALUE has been outside the allowed interval 6907-10907 for 2s Some possible explanations why the error has occurred: - The VFC, (voltage to frequency) IC 15 on control driver board, or some component around it is broken - IC 23 broken (control driver board)

C CFM 020 010

MEASURED MAGNETIZATION CURRENT INCORRECT Unconditional error, blood pump available General description of conditions for occurring: - Measured magnetization current differs to much from typical value. Technical description of conditions for occurring: - UF coil current is outside the limits 0.18 A - 0.28 A for 5 seconds.



29 (115)

Some possible explanations why the error has occurred: - UF cell broken - Bad connection between UF cell and control driver board - Broken control driver board C CFM 020 011

UF CELL TARATION NOT APPROVED Unconditional error, blood pump available General description of conditions for occurring: - A self calibration (taration) was run. It failed as the values of the variables FRR(FR_UFRTOLERANCE) and FRR(FR_UFROFFSET) had changed too much since the last self calibration. A new self calibration was run after 5 minutes. It did also fail for the same reason. Technical description of conditions for occurring: - CalibrDiffFlowNew differed more than 1 ml/min from CalibrDiffFlowOld A new self calibration was done after 5 minutes. CalibrDiffFlow again differed more than 1.0 ml/min from CalibrDiffFlowNew AND CalibrDiffFlow again differed more than 1.0 ml/min from CalibrDiffFlowOld Some possible explanations why the error has occurred: - UF cell broken or dirty - There is air through the UF cell - Leakage through: RIVA, ZEVA, DIVA or TAVA

C CFM 020 012

UF CELL TARATION NOT APPROVED Unconditional error, blood pump available General description of conditions for occurring: - A self calibration (taration) was run. It failed as the value of the variable FRR(FR_UFRTOLERANCE) differed too much from the value that was stored in the EEPROM or estimated at the last performed self calibration. Technical description of conditions for occurring: CALIBR DIFF FLOWnew differed more than 7.5 ml/min from CALIBR DIFF FLOWold Some possible explanations why the error has occurred: - UF cell broken or dirty - There is air through the UF cell - Leakage through: RIVA, ZEVA, DIVA or TAVA

C CFM 020 014

TOO LOW SELF CALIBRATION FLOW Unconditional error, blood pump available General description of conditions for occurring: - The flow measuring unit measured a flow through channel 1 that was less than 100 ml/min during self calibration (taration). Technical description of conditions for occurring: - FRR(FR_CH1RATE) < 100.0 ml/min. Some possible explanations why the error has occurred: - Uncalibrated or broken. pressure regulator - Dirty flow restrictor. - Dirty outlet restrictor

30 (115)



- Dirty or broken flow pump:. - Dirty or broken suction pump. - Broken or uncalibrated degassing pressure transducer. - ZEVA: leakage - RIVA: leakage C CFM 020 015

UNSTABLE FLOW SIGNALS DURING SELF CALIBRATION Unconditional error, blood pump available General description of conditions for occurring: - The self calibration (taration) failed because at least one of the measured flow signals varied too much. A new self calibration that was done 5 minutes later did also fail because at least one of the measured flow signals varied too much. Technical description of conditions for occurring: - Variance of the flow signals were calculated The differential flow during either the offset calibration or during the differential flow varied too much Some possible explanations why the error has occurred: - Air is flowing through flow channel 1. There is too much air in the inlet water - Valves: RIVA, ZEVA, diva or TAVA are leaking - Flow cell: the flow cell is dirty. - Flow cell: the flow cell is broken - Flow restrictor: the restrictor is dirty - Flow pump: the pump is not working properly - Degassing chamber: the o-ring at the top of the chamber is not in its correct position fluid is leaking. - Degassing pressure transducer: not working properly.

C CFM 020 016

SELF CALIBRATION TIME OUT Unconditional error, blood pump available General description of conditions for occurring: - The self calibration (taration) executed for a too long time. Technical description of conditions for occurring: - Self calibration time > max. self calibration time (max. self calibration time = 15s - 68s) Some possible explanations why the error has occurred: - Secondary error to the error C CFM 020 006 - Secondary error to the error C CFM 020 007 - Secondary error to the error C CFM 020 008 - Secondary error to the error C CFM 020 009.

C CFM 020 017

VFC CALIBRATION TIME OUT (VFC1 OFFSET). Unconditional error, blood pump available General description of conditions for occurring: - Please refer to the description of C CFM 020 008

C CFM 020 018

VFC CALIBRATION TIME OUT (VFC2 OFFSET). Unconditional error, blood pump available General description of conditions for occurring: - Please refer to the description of C CFM 020 009



31 (115)

C CFM 020 019

VFC CALIBRATION TIME OUT (VFC1 REFERENCE). Unconditional error, blood pump available General description of conditions for occurring: - Please refer to the description of C CFM 020 006

C CFM 020 020

VFC CALIBRATION TIME OUT (VFC2 REFERENCE). Unconditional error, blood pump available General description of conditions for occurring: - Please refer to the description of C CFM 020 007

C CFM 020 021

MEASURED MAGNETIZATION CURRENT INCORRECT Unconditional error, blood pump available General description of conditions for occurring: - Please refer to the description of C CFM 020 010

C CFM 020 024

UNSTABLE SIGNAL DURING UF CELL CALIBRATION General description of conditions for occurring: - The UF cell calibration failed because at least one of the measured flow signals varied too much Some possible explanations why the error has occurred: - Air is flowing through flow channel 1. There is too much air in the inlet water - Valves: RIVA, ZEVA, diva or TAVA are leaking - Flow cell: the flow cell is dirty. - Flow cell: the flow cell is broken - Flow restrictor: the restrictor is dirty - Flow pump: the pump is not working properly - Degassing chamber: the o-ring at the top of the chamber is not in its correct position. fluid is leaking. - Degassing pressure transducer: not working properly.

C CFM 020 025

UNSTABLE SIGNAL DURING UF OFFSET CALIBRATION Unconditional error, blood pump available General description of conditions for occurring: - The channel 1 flow signal and the channel 2 flow signal varied too much during the main flow offset calibration in service mode. There should be no flow through the measuring cells. Technical description of conditions for occurring: - The variance of the channel 1 flow and the variance of the channel 2 flow were out of limit Some possible explanations why the error has occurred: - The flow cell is dirty - The flow cell is broken - BYVA/DIVA/TAVA leakage

C CFM 020 029

UF CALIBRATION REFERENCE VOLUME OUT OF LIMIT Unconditional error, blood pump available General description of conditions for occurring: - The reference volume was outside its specified limits during the UF calibration in service mode.

32 (115)



Technical description of conditions for occurring: ORI(OI_UFCalRefVol) < PI(EPI_UFCalRefVolLl) or ORI(OI_UFCalRefVol) > PI(EPI_UFCalRefVolHl) Some possible explanations why the error has occurred: - Memory RAM corrupt C CFM 020 030

CASE ERROR Unconditional error, blood pump available General description of conditions for occurring: - Internal software error

C CFM 020 031


C CFM 020 032


C CFM 020 033

UF PULS TIMER ERROR Unconditional error, blood pump available General description of conditions for occurring: - The UF pulse timer is not working properly. Technical description of conditions for occurring: - The timer 9513 has returned error message(s). Some possible explanations why the error has occurred: - The timer IC 34 on the control driver board is broken.

C CFM 020 034

UF INTERRUPT TIMER ERROR Unconditional error, blood pump available General description of conditions for occurring: - The UF interrupt timer is not working properly. Technical description of conditions for occurring: - The timer 9513 has returned error message(s). Some possible explanations why the error has occurred: - The timer IC 23 on the control driver board is broken.

C CFM 020 035

VFC BUFFER FULL ERROR Unconditional error, blood pump available General description of conditions for occurring: - The UF interrupt procedure has filled the VFC data buffer. Some possible explanations why the error has occurred: - Software error - The timer IC 23 on the control driver board is broken. - The interrupt controller is broken



33 (115)

C CFM 020 036

VFC BUFFER OVERFLOW ERROR Unconditional error, blood pump available General description of conditions for occurring: - Software error

C CFM 020 037

MUX MISMATCH OCCURRED TOO MANY TIMES Unconditional error, blood pump available General description of conditions for occurring: - Software error

C CFM 020 038

C CFM 020 039

MUX ERROR Unconditional error, blood pump available General description of conditions for occurring: - Software error UNSTABLE FLOW SIGNALS DURING SELF CALIBRATION Unconditional error, blood pump available General description of conditions for occurring: - The self calibration (taration) failed because at least one of the measured flow signals varied too much. A new self calibration that was done 5 minutes later did also fail because at least one of the measured flow signals varied too much. Technical description of conditions for occurring: - Variance of the flow signals were calculated The flow through one or both of the UF channels during the differential flow calibration stage varied too much. Some possible explanations why the error has occurred: - Air is flowing through flow channel 1. There is too much air in the inlet water - Valves: RIVA, ZEVA, diva or TAVA are leaking - Flow cell: the flow cell is dirty. - Flow cell: the flow cell is broken - Flow restrictor: the restrictor is dirty - Flow pump: the pump is not working properly - Degassing chamber: the o-ring at the top of the chamber is not in its correct position. fluid is leaking. - Degassing pressure transducer: not working properly. - This error code occurs if an internal UF-calibration is made in P5.00, P6.00 or P7.00

C CFT 020, Flow Meter, Treatment Mode C CFT 020 000


C CFT 020 001

INCORRECT FLOW FROM CHANNEL 2 Unconditional error, blood pump available General description of conditions for occurring: Flow deviation in channel 2 Technical description of conditions for occurring:

34 (115)



The flow deviation in channel 2 (compared with channel 1 + UFrate) exceeded 100ml/min for 30 seconds a second time during the same treatment. The first Time this occur, a forced taration is performed. Some possible explanations why the error has occurred: UF-cell broken

C CF 021, UF Rate Filter C CF 021 000




35 (115)

C CF 022, UF Rate Regulator C CF 022 000


C CFS 023, Dia Pressure, Service Mode C CFS 023 000


C CFT 026, UF Volume Accumulation, Treatment Mode C CFT 026 000


C CF 027, Disinfection Valves C CF 027 000


C CFD 028, MM95, Cond. Control, Disinfection Mode C CFD 028 000


C CFD 028 001

TOO LOW CHEMICAL MIXING RATIO Unconditional error General description of conditions for occurring: - The chemical mixing ratio is too low. Technical description of conditions for occurring: - ORI(OI_ChemMixRatio) < 9 Some possible explanations why the error has occurred: - Incorrect preset of concentration preset (Preset 6-0-0-10, 6-0-110, 6-0-2-10 or 6-1-1-9). - Internal software error

36 (115)



C CFF 028, MM95, Cond. Control, Function Check C CFF 028 000


C CFM 028, MM95, Cond. Control C CFM 028 000


C CFM 028 001

CONCENTRATE PUMP TIMER ERROR Unconditional error, blood pump available General description of conditions for occurring: - The concentrate pump timer is not working properly. Technical description of conditions for occurring: - The timer 9513 has returned error message(s). Some possible explanations why the error has occurred: - The timer IC 21 on the control U board is broken.

C CFM 028 002

CONFIGURATION ERROR Unconditional error, blood pump available General description of conditions for occurring: - Internal software error

C CFM 028 003

HIGH INLET WATER CONDUCTIVITY Unconditional error, blood pump available General description of conditions for occurring: - Inlet water conductivity is too high

C CFS 028, MM95, Cond. Control, Service Mode C CFS 028 000


C CFT 028, MM95, Cond. Control Treatment Mode C CFT 028 000




37 (115)

C CF 029, Fluid composition supervision C CF 029 000


C CF 030, Remaining Disinfection Time Calculation C CF 030 000


C CF 031, Bicart Valve C CF 031 000


C CF 032, AK 96, UF Logging C CF 032 000


C CFT 033, UF Gain Control C CFT 033 000


C CFT 036, Diascan C CFT 036 000

CASE ERROR No more Diascan measurements are possible. General description of conditions for occurring: - Internal software error

C CFT 036 201

CASE ERROR REMOVED FROM PROGRAM VERSION 3.20 No more Diascan measurements are possible. General description of conditions for occurring: - Internal software error

C CFT 036 210

38 (115)

CASE ERROR REMOVED FROM PROGRAM VERSION 3.20



General description of conditions for occurring: - Internal software error C CFT 036 211

CASE ERROR REMOVED FROM PROGRAM VERSION 3.20 No more Diascan measurements are possible. General description of conditions for occurring: - Internal software error

C CFT 036 212

CASE ERROR REMOVED FROM PROGRAM VERSION 3.20 General description of conditions for occurring: - Internal software error

C CFT 036 220


C CFT 036 221


C CFT 036 222


C CFT 036 223


C CFT 036 224


C CFT 036 225


C CFT 036 226


C CFT 036 227


CASE ERROR REMOVED FROM PROGRAM VERSION 3.20


39 (115)

General description of conditions for occurring: - Internal software error C CFT 036 231


C CFT 036 298


C CFT 036 299


C CFS 068, UF calibration box mode function C CFS 068 000


C CFS 068 001

SET DISCRETE PORT ERROR Unconditional error, blood pump available General description of conditions for occurring: - Internal software error

C CFS 068 002


C CFS 068 003


C CFS 068 004


C CFS 068 005


40 (115)



C CFT 069, Disinfection control C CFT 069 000




41 (115)

C CFT 080, Variable flow control C CFT 080 000


C CF 080 001

VARIABLE FLOW CALIBRATION VALUE ERROR Unconditional error, blood pump not available General description of conditions for occurring: -The checksum of the EEPROM of control U is incorrect Make a default preset, restart the machine and calibrate the variable flow motor. Some possible explanations why the error has occurred: - Broken safe-RAM (battery-RAM)

C CF 080 002

VARIABLE FLOW CALIBRATION VALUE ERROR Unconditional error, blood pump not available General description of conditions for occurring: -The calibrated variable flow motor value was out of range. It has been automatically changed to a default value. Make a default preset, restart the machine and calibrate the variable flow motor. Some possible explanations why the error has occurred: - Internal software error - Broken safe-RAM (battery-RAM)

C CF 080 003

VARIABLE FLOW HISTORY UPDATE ERROR Unconditional error, blood pump not available General description of conditions for occurring: -The variable flow history could not be updated due to some reason below. -The checksum of the EEPROM of control U is incorrect. Make a default preset, restart the machine and calibrate the variable flow motor. Some possible explanations why the error has occurred: - Broken safe-RAM (battery-RAM)

C CF 080 004

VARIABLE FLOW CALIBRATION VALUE UPDATE ERROR Unconditional error, blood pump not available General description of conditions for occurring: -The calibrated value for the variable flow history could not be updated due to some reason below. -The checksum of the EEPROM of control U is incorrect. Make a default preset, restart the machine and calibrate the variable flow motor. Some possible explanations why the error has occurred: - Broken safe-RAM (battery-RAM)

42 (115)



C CO 001, E2PROM SCAN C CO 001 000


C CO 002, Key Board C CO 002 000


C CO 002 001

DISC. I/O ERROR Transient error General description of conditions for occurring: - Internal software error

C CO 002 002

LOW RESOLUTION DISPLAY USED WITH CHINESE LANGUAGE General description of conditions for occurring: It is not possible to use Chinese language together with the low resolution display (240 x 64 pixels). The Display needs to be exchanged in order to use Chinese language.

C CO 003, Venous Pressure Bargraph C CO 003 000


C CO 004, Blood Flow Bargraph C CO 004 000


C CO 005, Conductivity Bargraph C CO 005 000




43 (115)

C CO 006, Temperature Bargraph C CO 006 000


C CO 009, UF Volume Bargraph C CO 009 000


C CO 010, UF Rate Bargraph C CO 010 000


C CO 010 001


C CO 011, ON/OFF Lamp C CO 011 000


C CO 012, Rinse Lamp C CO 012 000


C CO 013, Reset Lamp C CO 013 000


44 (115)



C CO 015, Isol UF Mode Lamp C CO 015 000


C CO 016, Volume Control Mode Lamp C CO 016 000


C CO 019, Single Needle Limits Lamp C CO 019 000


C CO 022, Heparin Lamp C CO 022 000


C CO 023, Time Lamp C CO 023 000


C CO 026, UF Volume Lamp C CO 026 000


C CO 027, UF Rate Lamp C CO 027 000




45 (115)

C CO 030, Attention Lamp C CO 030 000


C CO 031, Technical Error Lamp C CO 031 000


C CO 032, Auto Heat Lamp C CO 032 000


C CO 034, Blood Pump Lamp C CO 034 000


C CO 035, Auto Rinse Lamp C CO 035 000


C CO 037, Fluid By Lamp C CO 037 000


C CO 038, UF Start/Stop Lamp C CO 038 000


46 (115)



C CO 041, Blood Flow Path Lamp C CO 041 000


C CO 042, Fluid Flow Path Lamp C CO 042 000


C CO 042 001


C CO 042 002

FLUID BY ERROR Transient error General description of conditions for occurring: - Internal software error

C CO 043, Information Display C CO 043 000


C CO 043 256

INFORMATION DISPLAY TABLE ERROR (1) General description of conditions for occurring: - Internal software error

C CO 043 257

INFORMATION DISPLAY TABLE ERROR (2) General description of conditions for occurring: - Internal software error

C CO 043 260

LANGUAGE SELECT ERROR General description of conditions for occurring: - Internal software error

C CO 043 261

DISC. I/O ERROR General description of conditions for occurring: - Internal software error

C CO 043 262


DISC. I/O ERROR


47 (115)

General description of conditions for occurring: - Internal software error C CO 043 263

DISC. I/O ERROR General description of conditions for occurring: - Internal software error

C COS 043, Information Display, Service Mode C COS 043 016

INFORMATION DISPLAY TABLE ERROR, SERVICE TEXT Transient error General description of conditions for occurring: - Internal software error

C COS 043 017

INFORMATION DISPLAY TABLE ERROR, CALIBRATION TEXTS Transient error General description of conditions for occurring: - Internal software error

C COS 043 018

INFORMATION DISPLAY TABLE ERROR, TRANSDUCER NUMBER Transient error General description of conditions for occurring: - Internal software error

C COS 043 019

VARIABLE SCALING ERROR Transient error General description of conditions for occurring: - Internal software error

C COM 044, Manual Input C COM 044 000


C COP 044, Manual Input, Preset Mode C COP 044 000


C COS 044, Manual Input, Service Mode C COS 044 xxx


48 (115)



C COT 044, Manual Input, Treatment Mode C COT 044 xxx


C CO 045, Blood Pump Knob C CO 045 000


C CO 045 001

INCORRECT BLOOD TUBE DIAMETER (PRESET VALUE) Transient error General description of conditions for occurring: - The parameter for the set value of the blood tube diameter is out of limit. Technical description of conditions for occurring: - ORI(OI_BlTubeDiam) < PI(EPI_BlTubeDiamLl) or ORI(OI_BlTubeDiam) > PI(EPI_BlTubeDiamHl) Some possible explanations why the error has occurred: - Internal software error - Read/write memory error (re-preset and restart AK 96)

C CO 045 002


C CO 049, Time Calculation C CO 049 000


C CO 050, Remaining Time Calculation C CO 050 000


C CO 051, Non Diffusion Time Calculation C CO 051 000


CASE ERROR Transient error


49 (115)

General description of conditions for occurring: - Internal software error

C CO 053, Buzzer Control C CO 053 000


C CO 054, Time Display C CO 054 000


C CO 060, Heparin Auto Stop Limit C COS 060 000


C CO 062, Priming Lamp C CO 062 000


C CO 067, Auto Priming Lamp C CO 067 000


C CO 069, BSM, Reset Limits And Set Value C CO 069 000


C CO 072, Conductivity C CO 072 000

CASE ERROR Transient error General description of conditions for occurring:

50 (115)



- Internal software error

C CO 073, Conductivity Profiling C CO 073 000


C CO 073 001


C CO 073 002


C CO 074, UF Profiling C CO 074 000


C CO 075, Chem Lamp C CO 075 000


C CO 076, Heat Lamp C CO 076 000


C CO 077, Rinse Back Lamp C CO 077 000


C CO 079, Concentrate Bank C CO 079 000


CASE ERROR Transient error AK 96® - Error Codes

51 (115)

General description of conditions for occurring: - Internal software error C CO 079 001


C CO 079 002


C CO 080, Attention C CO 080 000


C CO 080 001


C CO 080 002

EVALUATION STATE ERROR Transient error General description of conditions for occurring: - Internal software error

C CO 080 003

ATTENTION QUEUE ERROR Transient error General description of conditions for occurring: - Internal software error - Corrupt RAM memory

C CO 084, Disinfection Bank Selection C CO 084 000


C CO 084 001


52 (115)



C CO 087, Protective Set C CO 087 000


C CO 096, Profiling C CO 096 000


C COxx 071, WRO 300 H communication C COFF 071 000


C COFF 071 001

ERROR IN OUTPUT SIGNAL TO U Transient error General description of conditions for occurring: Internal software error

C COFF 071 002

LOGICAL ERROR IN COMMUNICATION PROTOCOL Transient error General description of conditions for occurring: Internal software error

C COxx 088, Functional Check C CO 088 000


C COFB 088 001

AIR DETECTOR TEST ERROR, U P Unconditional error, blood pump not available General description of conditions for occurring: - U P air detector does not detect “air” when the transmitted intensity is lowered during Fch. Technical description of conditions for occurring: - PRI(PI_AirDetAirPErrCnt) > 10 Some possible explanations why the error has occurred: - Air detector broken - Broken BM I/O board (IC5, IC14 and components, IC12, IC17, Q6, Q7, IC19 and components)



53 (115)

- Broken protective U board (IC43 and components) (N.E. IC48) - Broken protective driver board (IC6 and components, V6 and components, IC4 and components, IC55) C COFB 088 002

AIR DETECTOR TEST ERROR, U W Unconditional error, blood pump not available General description of conditions for occurring: - U W air detector does not detect “air” when the transmitted intensity is lowered during Fch. Technical description of conditions for occurring: - PRI(PI_AirDetAirWErrCnt) > 10 Some possible explanations why the error has occurred: - Air detector broken - Broken BM I/O board (IC5, IC14 and components, IC12, IC17, Q6, Q7, IC19 and components) - Broken protective U board (IC3 and components) - Broken protective driver board (IC2 and components, V3 and components, IC1 and components, IC55)

C COFB 088 003

AIR DETECTOR TEST ERROR, U P AND W Unconditional error, blood pump not available General description of conditions for occurring: - One or both of U P and U W’s air detectors does not sense alarm free status when the transmitted intensity is increased to normal level. This error code should only occure if anything is done with the air detector during the low intensity test phase, since this condition (alarm free status) was already fulfilled at the start of the test. Technical description of conditions for occurring: - PRI(PI_AirDetNoAirErrCnt) > 10 Some possible explanations why the error has occurred: - Low level in venous drip chamber. Check the level and restart the monitor.

C COFF 088 004

BLOOD LEAK DETECTOR TEST ERROR, VALUE TOO HIGH Unconditional error, blood pump available General description of conditions for occurring: - The blood leak detector value is too high when the LED is off. Technical description of conditions for occurring: - PRI(PI_BlLeakOffLevelErrCnt) > 4 - Blood leak detector value > 2mV measured by ADC (U P) Some possible explanations why the error has occurred: - Blood leak detector uncalibrated - Blood leak detector unit broken - Too much external light in blood leak detector ( AK 96 open for service) - Broken protective driver board (R71 and components, IC29, IC25) - Broken/uncalibrated A/D system, protective driver board (IC12, IC13, IC15, and components)

C COFF 088 005

54 (115)

BLOOD LEAK DETECTOR TEST ERROR, VALUE OUT OF LIMIT



Unconditional error, blood pump available General description of conditions for occurring: - The blood leak detector value is out of the limits when the LED is lit Technical description of conditions for occurring: - PRI(PI_BlLeakOnLevelErrCnt) > 4 - Blood leak detector value < -10 or blood leak detector value > +60 (AK95P.U_P.SUP.MEAS.AD_INPUT.blLeakValue) Some possible explanations why the error has occurred: - Blood leak detector uncalibrated - Blood leak detector dirty - Blood leak detector broken - Broken protective driver board (R71 and components, IC29, IC25) - Broken/uncalibrated A/D system, protective driver board (IC12, IC13, IC15, and components) C COFF 088 006

BLOOD LEAK DETECTOR TEST ERROR, UNSTABLE OFF Unconditional error, blood pump available General description of conditions for occurring: The blood leak detector value is unstable when the LED is turned off. Technical description of conditions for occurring: - PRI(PI_BlLeakOffStableErrCnt) > 4 - Blood leak detector variance >5 Some possible explanations why the error has occurred: - Blood leak detector broken - Broken protective driver board (R71 and components, IC29, IC25) - Broken/uncalibrated A/D system, protective driver board (IC12, IC13, IC15, and components)

C COFF 088 007

BLOOD LEAK DETECTOR TEST ERROR, UNSTABLE ON Unconditional error, blood pump available General description of conditions for occurring: The blood leak detector value is unstable when the LED is turned on. Technical description of conditions for occurring: - PRI(PI_BlLeakOnStableErrCnt) > 4 - Blood leak detector variance >5 Some possible explanations why the error has occurred: - Blood leak detector broken - Broken protective driver board (R71 and components, IC29, IC25) - Broken/uncalibrated A/D system, protective driver board (IC12, IC13, IC15, and components)

C COFB 088 008

BLOOD PUMP TEST ERROR, PUMP NOT RUNNING (FIRST TEST) Unconditional error, blood pump not available General description of conditions for occurring: - The blood pump was commanded to run. The blood pump tacho value is too low AND the rotation indicator is not detecting



55 (115)

movement (first check). Technical description of conditions for occurring: - PRI(PI_BlPumpEdge1ErrCnt) > 10 Some possible explanations why the error has occurred: - Blood pump not connected to BM I/O board, P602 - Pump rotation indicator (P605) AND tacho (P604) not connected to BM I/O - Blood pump electronics broken (BM I/O IC7, IC3, IC11, IC8, Q1-4 and components). C COFB 088 009

BLOOD PUMP TEST ERROR, PUMP NOT RUNNING (SECOND TEST) Unconditional error, blood pump not available General description of conditions for occurring: - The blood pump was commanded to run. The blood pump tacho value is too low AND the rotation indicator is not detecting movement (second check). Technical description of conditions for occurring: - PRI(PI_BlPumpEdge2ErrCnt) > 4 Some possible explanations why the error has occurred: - Blood pump not connected to BM I/O board, P602 - Pump rotation indicator (P605) AND tacho (P604) not connected to BM I/O - Blood pump electronics broken (BM I/O IC7, IC3, IC11, IC8, Q1-4 and components).

C COFB 088 010

BLOOD PUMP TEST ERROR, PUMP NOT STOPPED (U P) Unconditional error, blood pump not available General description of conditions for occurring: - The blood pump was commanded to stop by U P. The measured values from tacho and/or rotation indicator show that the blood pump is still running. Technical description of conditions for occurring: - PRI(PI_BlPumpPStopErrCnt) > 4 Some possible explanations why the error has occurred: - Broken BM I/O board, IC11 and components - Broken protective driver board, IC 32

C COFB 088 011

BLOOD PUMP TEST ERROR, PUMP NOT RUNNING ROTATION INDICATOR, (FIRST CHECK) Unconditional error, blood pump not available General description of conditions for occurring: - The blood pump was commanded to run. The blood pump tacho value is OK but the rotation indicator has not detected any movement (first check) Technical description of conditions for occurring: - PRI(PI_BlPumpRotate1ErrCnt) > 10 Some possible explanations why the error has occurred: - The rotation indicator is broken or unconnected to BM I/O board

56 (115)



(P605) - Broken BM I/O board (Z3, R51, R47) - Broken protective driver board, IC39 C COFB 088 012

BLOOD PUMP TEST ERROR, PUMP NOT RUNNING ROTATION INDICATOR, (SECOND CHECK) Unconditional error, blood pump not available Unconditional error, blood pump not available General description of conditions for occurring: - The blood pump was commanded to run. The blood pump tacho value is OK but the rotation indicator has not detected any movement (first check) Technical description of conditions for occurring: - PRI(PI_BlPumpRotate2ErrCnt) > 4 Some possible explanations why the error has occurred: - The rotation indicator is broken or unconnected - Broken BM I/O board (Z3, R51, R47) - Broken protective driver board, IC39

C COFB 088 013

BLOOD PUMP TEST ERROR, PUMP NOT RUNNING TACHO SIGNALS MISSING, (FIRST CHECK) Unconditional error, blood pump not available General description of conditions for occurring: - The blood pump was commanded to run. The blood pump rotation indicator has detected movement but tacho value is too low (first check) Technical description of conditions for occurring: - PRI(PI_BlPumpTach1ErrCnt) > 10 Some possible explanations why the error has occurred: - Blood pump tacho broken or unconnected to BM I/O board (P604) - Broken control driver board (IC34)

C COFB 088 014

BLOOD PUMP TEST ERROR, PUMP NOT RUNNING TACHO SIGNALS MISSING, (SECOND CHECK) Unconditional error, blood pump not available General description of conditions for occurring: - The blood pump was commanded to run. The blood pump rotation indicator has detected movement but tacho value is to low (second check) Technical description of conditions for occurring: - PRI(PI_BlPumpTach2ErrCnt) > 4 Some possible explanations why the error has occurred: - Blood pump tacho broken or unconnected to BM I/O board (P604) - Broken control driver board (IC34)

C COFB 088 015

BLOOD PUMP TEST ERROR, PUMP NOT STOPPED (U W) Unconditional error, blood pump not available General description of conditions for occurring: - The blood pump was commanded to stop by U W. The measured values from tacho and/or rotation indicator show that the



57 (115)

blood pump is still running. Technical description of conditions for occurring: - PRI(PI_BlPumpWStopErrCnt) > 4 Some possible explanations why the error has occurred: - Broken BM I/O board (IC1, IC15) - Broken protective U board (IC10, IC7, IC5) (N.E.: IC10, IC7, IC6) C COFB 088 016

COMMUNICATION ERROR BETWEEN U W AND P (BM1) Unconditional error, blood pump not available General description of conditions for occurring: - U W does not agree on that the blood monitor function check part 1 is ready Technical description of conditions for occurring: - PRI(PI_Bm1ErrCnt) > 2 Some possible explanations why the error has occurred: - Broken protective U board (IC26, V4 and components)

C COFB 088 017

COMMUNICATION ERROR BETWEEN U W AND P (BM1) Unconditional error, blood pump not available General description of conditions for occurring: - U W does not agree on that the blood monitor function check part 2 is ready Technical description of conditions for occurring: - PRI(PI_Bm2ErrCnt) > 2 Some possible explanations why the error has occurred: - Broken protective U board (IC26, V4 and components)

C COFB 088 018

BUZZER TEST ERROR, BUZZER NOT ON (U P) Unconditional error, blood pump not available General description of conditions for occurring: - The microphone can not detect that the U P buzzer is on Technical description of conditions for occurring: - PRI(PI_BuzzPOnErrCnt) > 3 Some possible explanations why the error has occurred: - U P buzzer is broken (H2 on protective driver board) - Protective driver board broken (IC39, IC21, IC16, M1(microphone), IC5, V8, V7 and components) It is not possible to mute buzzer

C COFB 088 019

BUZZER TEST ERROR, BUZZER NOT OFF (U P) Unconditional error, blood pump not available General description of conditions for occurring: - The microphone can not detect that the U P buzzer is off Technical description of conditions for occurring: - PRI(PI_BuzzPOffErrCnt) > 3

58 (115)



Some possible explanations why the error has occurred: - Protective driver board broken (IC39, IC21, IC16, M1(microphone), IC5, V8, V7 and components) It is not possible to mute buzzer C COFB 088 020

BUZZER TEST ERROR, BUZZER NOT SILENT Unconditional error, blood pump not available General description of conditions for occurring: - The microphone can not detect that both the U P and the U W buzzer are off when the buzzer test starts Technical description of conditions for occurring: - PRI(PI_BuzzSilentErrCnt) > 3 Some possible explanations why the error has occurred: - Protective driver board broken (M1 (microphone), IC5, V8, V7 and components) It is not possible to mute buzzer

C COFB 088 021

BUZZER TEST ERROR, BUZZER NOT ON (U W) Unconditional error, blood pump not available General description of conditions for occurring: - The microphone can not detect that the U W buzzer is on Technical description of conditions for occurring: - PRI(PI_BuzzWOnErrCnt) > 3 Some possible explanations why the error has occurred: - U W buzzer is broken (H1 on protective U board) - Protective U board is broken (IC10, IC7) - Protective driver board broken (M1(microphone), IC5, V8, V7 and components) It is not possible to mute buzzer

C COFB 088 022

BUZZER TEST ERROR, BUZZER NOT OFF (U W) Unconditional error, blood pump not available General description of conditions for occurring: - The microphone can not detect that the U W buzzer is off Technical description of conditions for occurring: - PRI(PI_BuzzWOffErrCnt) > 3 Some possible explanations why the error has occurred: - Protective U board is broken (IC10, IC7) - Protective driver board broken (M1(microphone), IC5, V8, V7 and components) It is not possible to mute buzzer

C COFB 088 023

COMMUNICATION ERROR BETWEEN U W AND P (COM) Unconditional error, blood pump not available General description of conditions for occurring:



59 (115)

- U W does not agree on that the common function check is ready Technical description of conditions for occurring: - PRI(PI_ComErrCnt) > 2 Some possible explanations why the error has occurred: - Broken protective U board (IC26, V4 and components) C COFF 088 024

CONDUCTIVITY TEST ERROR, CONDUCTIVITY COMPARE ERROR (HIGH CONDUCTIVITY TEST) Unconditional error, blood pump available General description of conditions for occurring: - The conductivity difference between U C and U P is too large in the conductivity test high phase. - The difference between CondA (FRI(FI_MM90CONDA)) and CondP (AK95P.U_P.SUP.MEAS.AD_INPUT.condValue) is outside limit +/- 1mS/cm - The difference between CondA (FRI(FI_MM90CONDA)) and CondB (FRI(FI_MM90CONDB)) (AK95P.U_P.SUP.MEAS.AD_INPUT.condValue) is outside limit +/- 0.3mS/cm

Technical description of conditions for occurring: - PRI(PI_CondHighDiffErrCnt) > 4 - The difference between CondB (FRI(FI_MM90CONDB)) and CondP (AK95P.U_P.SUP.MEAS.AD_INPUT.condValue) is outside limit +/- 1mS/cm Some possible explanations why the error has occurred: - Conductivity cell B is broken or uncalibrated - Conductivity cell P is broken or uncalibrated - Conductivity cell A is broken or uncalibrated - The A/D converters are uncalibrated (U P, MM 95) C COFF 088 025

CONDUCTIVITY TEST ERROR, CONDUCTIVITY VALUE TOO LOW (HIGH CONDUCTIVITY TEST) Unconditional error, blood pump available General description of conditions for occurring: - The conductivity measured by U P is not high enough in the conductivity test high phase. Technical description of conditions for occurring: - PRI(PI_CondHighLevelErrCnt) > 4 - Conductivity value from CondP(AK95P.U_P.SUP.MEAS.AD_INPUT.condValue) <20 mS/cm Some possible explanations why the error has occurred: - Incorrect concentrate used (not possible to regulate conductivity >20mS/cm) - Air leakage (pickup tube, tube, filter) - Conductivity cell B is broken or uncalibrated - Conductivity cell P is broken or uncalibrated

60 (115)



- Conductivity cell A is broken or uncalibrated - A/D converter U P is uncalibrated C COFF 088 026

CONDUCTIVITY TEST ERROR, CONDUCTIVITY UNSTABLE (HIGH CONDUCTIVITY TEST) Unconditional error, blood pump available General description of conditions for occurring: - The conductivity value measured in U P is not stable in the high conductivity test Technical description of conditions for occurring: - PRI(PI_CondHighStableErrCnt) > 4 Some possible explanations why the error has occurred: - Too much air in fluid system - Conductivity cell B is broken or uncalibrated - Conductivity cell P is broken or uncalibrated - Conductivity cell A is broken or uncalibrated

C COFF 088 027

CONDUCTIVITY TEST ERROR, CONDUCTIVITY COMPARE ERROR (LOW CONDUCTIVITY TEST) Unconditional error, blood pump available General description of conditions for occurring: - The conductivity difference between U C and U P is too large in the conductivity test low phase. Technical description of conditions for occurring: - PRI(PI_CondLowDiffErrCnt) > 4 - The difference between CondB(FRI(FI_MM90CONDB)) and CondP(AK95P.U_P.SUP.MEAS.AD_INPUT.condValue) is outside limit +/- 1mS/cm - The difference between CondA (FRI(FI_MM90CONDA)) and CondP (AK95P.U_P.SUP.MEAS.AD_INPUT.condValue) is outside limit +/- 1mS/cm - The difference between CondA (FRI(FI_MM90CONDA)) and CondB (FRI(FI_MM90CONDB)) (AK95P.U_P.SUP.MEAS.AD_INPUT.condValue) is outside limit +/- 0.3mS/cm

Some possible explanations why the error has occurred: - Conductivity cell B is broken or uncalibrated - Conductivity cell P is broken or uncalibrated - Conductivity cell A is broken or uncalibrated - The A/D converters are uncalibrated (U P, MM 95) C COFF 088 028

CONDUCTIVITY TEST ERROR, CONDUCTIVITY VALUE TOO HIGH (LOW CONDUCTIVITY TEST) Unconditional error, blood pump available General description of conditions for occurring: - The conductivity measured by U P is not low enough in the conductivity test low phase. Technical description of conditions for occurring: - PRI(PI_CondLowLevelErrCnt) > 4



61 (115)

- Conductivity value from CondP (AK95P.U_P.SUP.MEAS.AD_INPUT.condValue) was >5 mS/cm Some possible explanations why the error has occurred: - Conductivity cell B is broken or uncalibrated - Conductivity cell P is broken or uncalibrated - Conductivity cell A is broken or uncalibrated C COFF 088 029

CONDUCTIVITY TEST ERROR, CONDUCTIVITY UNSTABLE (LOW CONDUCTIVITY TEST) Unconditional error, blood pump available General description of conditions for occurring: - The conductivity value measured in U P is not stable in the low conductivity test Technical description of conditions for occurring: - PRI(PI_CondLowStableErrCnt) > 4 Some possible explanations why the error has occurred: - Too much air in fluid system - Conductivity cell B is broken or uncalibrated - Conductivity cell P is broken or uncalibrated - Conductivity cell A is broken or uncalibrated

C COFF 088 030

FLOW SWITCH ERROR, FLOW DETECTED (INVA CLOSED) Unconditional error, blood pump available General description of conditions for occurring: - The flow switch senses fluid flow when INVA is closed. Technical description of conditions for occurring: - PRI(PI_FlowOffErrCnt) > 3 - PRL(P_FLOWSWITCHFLOW) = TRUE Some possible explanations why the error has occurred: - Flow switch broken - Float stucked in upper position - FM I/O board broken (IC2) - Protective driver board broken (IC28)

C COFF 088 031

FLOW SWITCH ERROR, NO FLOW (INLET PRESSURE OK) Unconditional error, blood pump available General description of conditions for occurring: - The flow switch does not sense flow when the inlet pressure (U C) is OK. Technical description of conditions for occurring: - PRI(PI_FlowOn1ErrCnt) > 3 - PRL(P_FLOWSWITCHFLOW) = FALSE Some possible explanations why the error has occurred: - Flow switch broken - Float stucked in lower position - FM I/O board broken (IC2) - Protective driver board broken (IC28)

C COFF 088 032

62 (115)

FLOW SWITCH ERROR, NO FLOW (INVA OPEN) Unconditional error, blood pump available



General description of conditions for occurring: - The flow switch does not sense flow when INVA is opened after the no flow test. - This error code is not used after P2.04 Technical description of conditions for occurring: - PRI(PI_FlowOn2ErrCnt) > 3 - PRL(P_FLOWSWITCHFLOW) = FALSE Some possible explanations why the error has occurred: - Flow switch broken - Float stucked in lower position - FM I/O board broken (IC2) - Protective driver board broken (IC28) C COFF 088 033

COMMUNICATION ERROR BETWEEN U W AND P (FM1) Unconditional error, blood pump available General description of conditions for occurring: - U W does not agree on that the fluid monitor function check part 1 is ready Technical description of conditions for occurring: - PRI(PI_Fm1ErrCnt) > 2 Some possible explanations why the error has occurred: - Broken protective U board (IC26, V4 and components)

C COFF 088 034

COMMUNICATION ERROR BETWEEN U W AND P (FM2) Unconditional error, blood pump available General description of conditions for occurring: U W does not agree on that the fluid monitor function check part 2 is ready Technical description of conditions for occurring: - PRI(PI_Fm2ErrCnt) > 2 Some possible explanations why the error has occurred: - Broken protective U board (IC26, V4 and components)

C COFF 088 035

HEATER TEST ERROR, HEATER ENERGIZED (INVA CLOSED) Unconditional error, blood pump available General description of conditions for occurring: - The heater is still energized after INVA has been closed. No flow in the monitor. - This error code is not used after P2.04 Technical description of conditions for occurring: - PRI(PI_HeaterOff1ErrCnt) > 3 - Signal PMAINS is high (+5V) Some possible explanations why the error has occurred: - P931 and P932 on heater relay board are incorrectly positioned - The heater relay board is broken (IC1 and components) - Protective driver board broken (IC25, IC 28)

C COFF 088 036


HEATER TEST ERROR, HEATER ENERGIZED (U P)


63 (115)

Unconditional error, blood pump available General description of conditions for occurring: - The heater is still energized when U P has turned the heater relay off. - This error code is not used after P2.04 Technical description of conditions for occurring: - PRI(PI_HeaterOff2ErrCnt) > 3 - Signal PMAINS is high (+5V) Some possible explanations why the error has occurred: - The heater relay board is broken (IC1 and components) - Protective driver board broken (IC25, IC 28) C COFF 088 037

HEATER TEST ERROR, HEATER NOT ENERGIZED (U C) Unconditional error, blood pump available General description of conditions for occurring: - The heater is not energized when there is flow through to the monitor and U C runs the heater with duty cycle 40 %. - This error code is not used after P2.04 Technical description of conditions for occurring: - PRI(PI_HeaterOn1ErrCnt) > 3 - Signal PMAINS is low (Zero volt) Some possible explanations why the error has occurred: - Broken fuse in AC/DC unit - Control U board broken (IC21) - Control driver board is broken (IC24) - Float stucked in lower position - Flow switch broken - Flow switch in incorrect position (should be mounted close to lower silicon connector) - FM I/O board is broken (Q1, Q2, Q3, Q4, R2) - Heater relay board is not connected - Protective U board is broken (signal PHEEN) - Protective driver board broken (IC25, IC 28) - The heater relay board is broken (K1, K2, V1, IC1 and components)

C COFF 088 038

HEATER TEST ERROR, HEATER NOT ENERGIZED (INVA OPEN) Unconditional error, blood pump available General description of conditions for occurring: - The heater is not energized when INVA is opened after the no flow test. - This error code is not used after P2.04 Technical description of conditions for occurring: - PRI(PI_HeaterOn2ErrCnt) > 3 - Signal PMAINS is low (Zero volt) Some possible explanations why the error has occurred: - Broken fuse in AC/DC unit - Control U board broken (IC21) - Control driver board is broken (IC24) - Float stucked in lower position

64 (115)



- Flow switch broken - Flow switch in incorrect position (should be mounted close to lower silicon connector) - FM I/O board is broken (Q1, Q2, Q3, Q4, R2) - Heater relay board is not connected - Protective U board is broken (signal PHEEN) - Protective driver board broken (IC25, IC 28) - The heater relay board is broken (K1, K2, V1, IC1 and components) C COFF 088 039

HEATER TEST ERROR, HEATER NOT ENERGIZED (U P) Unconditional error, blood pump available General description of conditions for occurring: - The heater is not energized when U P has enabled the heater relay. - This error code is not used after P2.04 Technical description of conditions for occurring: - PRI(PI_HeaterOn3ErrCnt) > 3 - Signal PMAINS is low (Zero volt) Some possible explanations why the error has occurred: - Broken fuse in AC/DC unit - Control U board broken (IC21) - Control driver board is broken (IC24) - Float stucked in lower position - Flow switch broken - Flow switch in incorrect position (should be mounted close to lower silicon connector) - FM I/O board is broken (Q1, Q2, Q3, Q4, R2) - Heater relay board is not connected - Protective U board is broken (signal PHEEN) - Protective driver board broken (IC25, IC 28) - The heater relay board is broken (K1, K2, V1, IC1 and components)

C COFB 088 040

HIGH VENOUS PRESSURE TEST ERROR, TOO HIGH VEN. PRESS. Unconditional error, blood pump not available General description of conditions for occurring: - U C regulates a too high venous pressure during the high venous pressure test. Technical description of conditions for occurring: - PRI(PI_HighVprPresErrCnt) > 1 - The venous pressure measured by U P (AK95P.U_P.SUP.MEAS.AD_INPUT.vprValue) > 300mmHg Some possible explanations why the error has occurred: - The venous pressure transducer board is broken/uncalibrated (U C) - The venous pressure transducer board is broken/uncalibrated (U P)

C COFB 088 041


HIGH VENOUS PRESSURE TEST ERROR, TOO BIG DIFFERENCE Unconditional error, blood pump not available


65 (115)

General description of conditions for occurring: - The difference between the measurements from the venous pressure transducers in U C and U P is to large. Technical description of conditions for occurring: - PRI(PI_HighVprTestErrCnt) > 3 - The venous pressure difference between U C (BRI(BI_VENPR)) and U P (AK95P.U_P.SUP.MEAS.AD_INPUT.vprValue) >15mmHg Some possible explanations why the error has occurred: - The venous pressure transducer board is broken/uncalibrated (U C) - The venous pressure transducer board is broken/uncalibrated (U P) - There is a leakage of pressure in U C or/and U P venous pressure transducer line. C COFB 088 042

PRIMING DETECTOR TEST ERROR, COMMUNICATION ERROR BETWEEN U P AND W Unconditional error, blood pump not available General description of conditions for occurring: - In priming detector test, U W does not send the calibrated priming detector transmitter current to U P. Technical description of conditions for occurring: - PRI(PI_PrimDetCalibCurrErrCnt) > 4 Some possible explanations why the error has occurred: - The protective U board is broken

C COFB 088 043

PRIMING DETECTOR TEST ERROR, CURRENT OUT OF LIMIT Unconditional error, blood pump not available General description of conditions for occurring: - The difference between the stored and the measured priming detector current was too big. Technical description of conditions for occurring: - PRI(PI_PrimDetCurrErrCnt) > 4 Some possible explanations why the error has occurred: - Priming detector is uncalibrated - Priming detector board is broken - U W is uncalibrated - Priming detector transmitter electronics broken (IC55, IC33, Q9, Q13 and components) on protective driver board. - Protective U board is broken (R29, C21)

C COFB 088 044

PRIMING DETECTOR TEST ERROR, BLOOD IN PRIMING DETECTOR (FIRST TEST), U P Unconditional error, blood pump not available General description of conditions for occurring: U P sensed “blood” when the priming detector test is started and the transmitter intensity is high. Technical description of conditions for occurring: - PRI(PI_PrimDetEmptyP1ErrCnt) > 10

66 (115)



Some possible explanations why the error has occurred: - Priming detector not connected to FM I/O board (P504) - Priming detector is not empty or priming detector dirty - Priming detector board is broken - Priming detector transmitter electronics broken (IC55, IC33, Q9, Q13 and components) on protective driver board. - Priming detector receiver electronics broken (IC18, V11, V12 and components) on protective driver board. C COFB 088 045

PRIMING DETECTOR TEST ERROR, BLOOD IN PRIMING DETECTOR (FIRST TEST), U W Unconditional error, blood pump not available General description of conditions for occurring: - U W sensed “blood” when the priming detector test is started and the transmitter intensity is high. Technical description of conditions for occurring: - PRI(PI_PrimDetEmptyW1ErrCnt) > 10 Some possible explanations why the error has occurred: - Priming detector not connected to FM I/O board (P504) - Priming detector is not empty or priming detector dirty - Priming detector board is broken - Priming detector transmitter electronics broken (IC55, IC33, Q9 and components) on protective driver board. - Priming detector receiver electronics broken (IC11, V9, V10 and components) on protective driver board.

C COFB 088 046

PRIMING DETECTOR TEST ERROR, NO BLOOD DETECTED (U P) Unconditional error, blood pump not available General description of conditions for occurring: - U P does not sense “blood” when the priming detector intensity is lowered. Technical description of conditions for occurring: - PRI(PI_PrimDetBloodPErrCnt) > 10 Some possible explanations why the error has occurred: - Priming detector board is broken - Priming detector transmitter electronics broken (IC55, IC33, Q9, Q13 and components) on protective driver board. - Priming detector receiver electronics broken (IC18, V11, V12 and components) on protective driver board.

C COFB 088 047

PRIMING DETECTOR TEST ERROR, NO BLOOD DETECTED (U W) Unconditional error, blood pump not available General description of conditions for occurring: - U W does not sense “blood” when the priming detector intensity is lowered. Technical description of conditions for occurring: - PRI(PI_PrimDetBloodWErrCnt) > 10 Some possible explanations why the error has occurred:



67 (115)

- Priming detector transmitter electronics broken (IC55, IC33, Q9 and components) on protective driver board. - Priming detector receiver electronics broken (IC11, V9, V10 and components) on protective driver board. - U W is uncalibrated/broken (IC10 on protective U board) C COFB 088 048

PRIMING DETECTOR TEST ERROR, BLOOD IN PRIMING DETECTOR (SECOND TEST), U P Unconditional error, blood pump not available General description of conditions for occurring: - U P sensed “blood” when the priming detector test intensity is high again after the low intensity test.. Technical description of conditions for occurring: - PRI(PI_PrimDetEmptyP2ErrCnt) > 10 Some possible explanations why the error has occurred: - Priming detector not connected to FM I/O board (P504) - Software error - Priming detector is not empty or priming detector dirty - Priming detector board is broken - Priming detector transmitter electronics broken (IC55, IC33, Q9, Q13 and components) on protective driver board. - Priming detector receiver electronics broken (IC18, V11, V12 and components) on protective driver board.

C COFB 088 049

PRIMING DETECTOR TEST ERROR, BLOOD IN PRIMING DETECTOR (SECOND TEST), U W Unconditional error, blood pump not available General description of conditions for occurring: U W sensed “blood” when the priming detector test intensity is high again after the low intensity test. Technical description of conditions for occurring: - PRI(PI_PrimDetEmptyW2ErrCnt) > 10 Some possible explanations why the error has occurred: - Priming detector not connected to FM I/O board (P504) - Priming detector is not empty or priming detector dirty - Priming detector board is broken - Priming detector transmitter electronics broken (IC55, IC33, Q9 and components) on protective driver board. - Priming detector receiver electronics broken (IC11, V9, V10 and components) on protective driver board. - U W is uncalibrated/broken (IC10 on protective U board)

C COFB 088 050

SAFETY RELAY TEST ERROR, REFERENCE CURRENT TOO HIGH Unconditional error, blood pump not available General description of conditions for occurring: - At the beginning of the relay test the current is measured when the relay is OFF (this current value is used as reference current in the following tests). The reference current measured was too high. Technical description of conditions for occurring: - PRI(PI_RelayOff1ErrCnt) > 4

68 (115)



Some possible explanations why the error has occurred: - The safety relay (K2) on control U board is broken - The valve current measuring system is broken (R20 and components) on protective driver board. - U P is uncalibrated C COFB 088 051

SAFETY RELAY TEST ERROR, TOO HIGH CURRENT DIFFERENCE (FIRST TEST) Unconditional error, blood pump not available General description of conditions for occurring: - The difference between the reference current and the second current value, measured when the relay is OFF, is too high (the safety relay is OFF and BYVA is open). Technical description of conditions for occurring: - PRI(PI_RelayOff2ErrCnt) > 4 Some possible explanations why the error has occurred: - The safety relay (K2) on control U board is broken - The valve current measuring system is broken (R20 and components) on protective driver board. - U P is uncalibrated

C COFB 088 052

SAFETY RELAY TEST ERROR, TOO LOW CURRENT DIFFERENCE (FIRST TEST) Unconditional error, blood pump not available General description of conditions for occurring: - The difference between the reference current and the first current value, measured when the relay is ON, is too small (safety relay is ON and BYVA is open). Technical description of conditions for occurring: - PRI(PI_RelayOn1ErrCnt) > 4 Some possible explanations why the error has occurred: - BYVA is not connected (or broken). - Protective driver board is broken (IC3, Q3) - The safety relay (K2) on control U board is broken - The valve current measuring system is broken (R20 and components) on protective driver board. - U P is uncalibrated

C COFB 088 053

SAFETY RELAY TEST ERROR, TOO LOW CURRENT DIFFERENCE (SECOND TEST) Unconditional error, blood pump not available General description of conditions for occurring: - The difference between the reference current and the second current value, measured when the relay is ON, is too small (safety relay is ON and BYVA is open). Technical description of conditions for occurring: - PRI(PI_RelayOn2ErrCnt) > 4 Some possible explanations why the error has occurred: - BYVA is not connected (or broken). - Protective driver board is broken (IC3, Q3) - The safety relay (K2) on control U board is broken



69 (115)

- The valve current measuring system is broken (R20 and components) on protective driver board. - U P is uncalibrated C COFB 088 054

SAFETY RELAY TEST ERROR, TOO HIGH CURRENT DIFFERENCE (SECOND TEST) Unconditional error, blood pump not available General description of conditions for occurring: - The difference between the reference current and the third current value, measured when the relay is ON, is too high (safety relay is ON and BYVA is closed. Technical description of conditions for occurring: - PRI(PI_RelayOn3ErrCnt) > 4 Some possible explanations why the error has occurred: - Protective driver board is broken (IC3, Q3) (BYVA does not close) - The valve current measuring system is broken (R20 and components) on protective driver board. - U P is uncalibrated

C COFF 088 055

TEMPERATURE TEST ERROR, TOO HIGH TEMPERATURE DIFFERENCE (HIGH TEMP. TEST) Unconditional error, blood pump available General description of conditions for occurring: - The temperature difference between U C and U P is too large in the temperature test high phase. TempC is measured in conductivity cell B. Technical description of conditions for occurring: - PRI(PI_TempHighDiffErrCnt) > 10 - TempC-TempP >1.3ºC or TempC-TempP <-0.6ºC Some possible explanations why the error has occurred: - U C A/D-system uncalibrated - U P A/D-system uncalibrated - Conductivity cell B broken - Conductivity cell P broken

C COFF 088 056

TEMPERATURE TEST ERROR, TOO LOW TEMPERATURE MEASURED (HIGH TEMP. TEST) Unconditional error, blood pump available General description of conditions for occurring: - The measured temperature (tempP) is lower than the test limit in the high temperature test. The temperature measured by tempP was below 41ºC even though the temperature had been increased a second time by U C. Technical description of conditions for occurring: - PRI(PI_TempHighLevelErrCnt) > 4 - tempP < 41ºC Some possible explanations why the error has occurred: - The temperature regulation system is broken (control U board) - U C A/D-system uncalibrated - U P A/D-system uncalibrated - Conductivity cell B broken

70 (115)



- Conductivity cell P broken C COFF 088 057

TEMPERATURE TEST ERROR, UNSTABLE TEMPERATURE (HIGH TEMP. TEST) Unconditional error, blood pump available General description of conditions for occurring: - The measured temperature value is not stable in the high temperature test . Technical description of conditions for occurring: - PRI(PI_TempHighStableErrCnt) > 4 Some possible explanations why the error has occurred: - The temperature regulation system is broken (control U board) - U P A/D-system uncalibrated - Conductivity cell P broken

C COFF 088 058

TEMPERATURE TEST ERROR, TOO HIGH TEMPERATURE DIFFERENCE (LOW TEMP. TEST) Unconditional error, blood pump available General description of conditions for occurring: The temperature difference between U C and U P is too large in the temperature test low phase. TempC is measured in conductivity cell B. Technical description of conditions for occurring: - PRI(PI_TempLowDiffErrCnt) > 4 Some possible explanations why the error has occurred: - U C A/D-system uncalibrated - U P A/D-system uncalibrated - Conductivity cell B broken - Conductivity cell P broken

C COFF 088 059

TEMPERATURE TEST ERROR, UNSTABLE TEMPERATURE (LOW TEMP. TEST) Unconditional error, blood pump available General description of conditions for occurring: - The measured temperature value is not stable in the low temperature test. Technical description of conditions for occurring: - PRI(PI_TempLowStableErrCnt) > 4 Some possible explanations why the error has occurred: - The temperature regulation system is broken (control U board) - U P A/D-system uncalibrated - Conductivity cell P broken

C COFF 088 060

DIVA/TAVA TEST ERROR, FAILURE TO ACHIEVE HIGH LEVEL IN DEAIRATING CHAMBER Unconditional error, blood pump available General description of conditions for occurring: - High level in the deairating chamber is not achieved at the start of valve leakage (DIVA/TAVA) test.



71 (115)

Technical description of conditions for occurring: - PRI(PI_ValveFillupErrCnt) > 4 Some possible explanations why the error has occurred: - Bad/no connection to level switch in deairating chamber. Check connection from level switch to FM I/O board (P503). - Level switch broken - EVVA is not open - TAVA is not closed - IC 28 on protective driver board broken - FIVA is malfunctioning (if the UFD-kit is installed) C COFF 088 061

DIVA/TAVA TEST ERROR, LEAKAGE IN HIGH PRESSURE TEST Unconditional error, blood pump available General description of conditions for occurring: - The dialysis pressure was measured twice with DIVA/TAVA/EVVA closed. The difference between the two pressure measurements was too big. Technical description of conditions for occurring: - PRI(PI_ValveHighLeakErrCnt) > 4 - The dialysis pressure changed more than +/-30mmHg between the two measurements. Some possible explanations why the error has occurred: - There is a leakage between the dialyzer connector and the by nipple. Check the o ring in the dialyzer connector. - The deairating chamber is leaking - DIVA/TAVA/EVVA/REVA is leaking - There is a leakage in the flow meter on the front of the machine - FIVA is leaking (if the UFD-kit is installed)

C COFF 088 062

DIVA/TAVA TEST ERROR, DIALYSIS PRESSURE OUTSIDE LIMITS IN THE LOW PRESSURE TEST (SECOND TEST) Unconditional error, blood pump available General description of conditions for occurring: - U C had regulated a dialysis fluid pressure at +200mmHg, measured at HPG. The dialysis fluid pressure, measured at the dialysis pressure transducer, was outside 200+/-20 mmHg. Technical description of conditions for occurring: - PRI(PI_ValveHighLevel1ErrCnt) > 4 - Dialysis fluid pressure outside 200+/-20 mmHg Some possible explanations why the error has occurred: - DIVA does not open - The HPG transducer or the dialysis pressure transducer is uncalibrated.

C COFF 088 063

72 (115)

DIVA/TAVA TEST ERROR, DIALYSIS PRESSURE OUTSIDE LIMITS IN THE HIGH PRESSURE TEST (FIRST TEST) Unconditional error, blood pump available



General description of conditions for occurring: - U C had regulated a dialysis fluid pressure at +200mmHg, measured at HPG. The dialysis fluid pressure, measured at the dialysis pressure transducer, was outside 200+/-20 mmHg. Technical description of conditions for occurring: - PRI(PI_ValveHighLevel2ErrCnt) > 4 - Dialysis fluid pressure outside 200+/-20 mmHg Some possible explanations why the error has occurred: - The HPG transducer or the dialysis pressure transducer is uncalibrated. - Unstable dialysis flow C COFF 088 064

DIVA/TAVA TEST ERROR, UNSTABLE PRESSURE IN HIGH PRESSURE TEST Unconditional error, blood pump available General description of conditions for occurring: - The dialysis pressure is not stable in the high pressure test. Regulated pressure approx. +200mmHg (HPG) Technical description of conditions for occurring: - PRI(PI_ValveHighStableErrCnt) > 4 - The dialysis fluid pressure variance was >20 Some possible explanations why the error has occurred: - There is too much air in the dialysis fluid - The HPG pressure transducer is broken - The dialysis fluid pressure transducer is broken

C COFF 088 065

DIVA/TAVA TEST ERROR, LEAKAGE IN LOW PRESSURE TEST Unconditional error, blood pump available General description of conditions for occurring: - The dialysis pressure was measured twice with DIVA/TAVA/EVVA closed. The difference between the two pressure measurements was too big. Technical description of conditions for occurring: - PRI(PI_ValveLowLeakErrCnt) > 4 - The dialysis pressure changed more than +/-20mmHg between the two measurements. Some possible explanations why the error has occurred: - There is a leakage between the dialyzer connector and the by nipple. Check the oring in the dialyzer connector. - The deairating chamber is leaking - DIVA/TAVA/EVVA/REVA is leaking - There is a leakage in the flow meter on the front of the machine - FIVA is leaking (if the UFD-kit is installed)

C COFF 088 066

DIVA/TAVA TEST ERROR, DIALYSIS PRESSURE OUTSIDE LIMITS IN LOW PRESSURE TEST (FIRST TEST) Unconditional error, blood pump available General description of conditions for occurring: - U C had regulated a dialysis fluid pressure at -200mmHg,



73 (115)

measured at HPG. The dialysis fluid pressure, measured at the dialysis pressure transducer, was outside -200+/-20 mmHg. Technical description of conditions for occurring: - PRI(PI_ValveLowLevel1ErrCnt) > 4 - Dialysis fluid pressure outside -200+/-20 mmHg Some possible explanations why the error has occurred: - The HPG transducer or the dialysis pressure transducer is uncalibrated. C COFF 088 067

DIVA/TAVA TEST ERROR, DIALYSIS PRESSURE OUTSIDE LIMITS IN HIGH PRESSURE TEST (SECOND TEST) Unconditional error, blood pump available General description of conditions for occurring: - U C had regulated a dialysis fluid pressure at -200mmHg, measured at HPG. The dialysis fluid pressure, measured at the dialysis pressure transducer, was outside -200+/-20 mmHg. Technical description of conditions for occurring: - PRI(PI_ValveLowLevel2ErrCnt) > 4 - Dialysis fluid pressure outside -200+/-20 mmHg Some possible explanations why the error has occurred: - TAVA does not open - The HPG transducer or the dialysis pressure transducer is uncalibrated.

C COFF 088 068

DIVA/TAVA TEST ERROR, UNSTABLE PRESSURE IN THE LOW PRESSURE TEST Unconditional error, blood pump available General description of conditions for occurring: - The dialysis pressure is not stable in the low pressure test. Regulated pressure approx. -200mmHg (HPG) Technical description of conditions for occurring: - PRI(PI_ValveLowStableErrCnt) > 4 - The dialysis fluid pressure variance was >20 Some possible explanations why the error has occurred: - There is too much air in the dialysis fluid - The HPG pressure transducer is broken - The dialysis fluid pressure transducer is broken

C COFB 088 069

VENOUS CLAMP TEST ERROR, CLAMP NOT OPEN AT START Unconditional error, blood pump not available General description of conditions for occurring: - The venous clamp is closed when the clamp test starts (the clamp is commanded open). Technical description of conditions for occurring: - PRI(PI_VClampOpen1ErrCnt) > 4 - BRL(B_VenClampClosed)=TRUE Some possible explanations why the error has occurred: - The venous clamp is stucked in closed position

74 (115)



- The clamp driver board is broken (transmitter-receiver) - Protective U board broken (R47, IC45, IC20, Q7, Q8, IC46, IC41, IC7) - Control U board broken (IC24) C COFB 088 070

VENOUS CLAMP TEST ERROR, CLAMP NOT OPEN (U P) Unconditional error, blood pump not available General description of conditions for occurring: The venous clamp does not open after it was closed by U P Technical description of conditions for occurring: - PRI(PI_VClampOpen2ErrCnt) > 4 - BRL(B_VenClampClosed)=TRUE Some possible explanations why the error has occurred: - The venous clamp is stucked in closed position - The clamp driver board is broken (transmitter-receiver) - Protective U board broken (R47, IC45, IC20, Q7, Q8, IC46, IC41, IC7) - Control U board broken (IC24)

C COFB 088 071

VENOUS CLAMP TEST ERROR, CLAMP NOT OPEN (U W) Unconditional error, blood pump not available General description of conditions for occurring: - The venous clamp does not open after it was closed by U W Technical description of conditions for occurring: - PRI(PI_VClampOpen3ErrCnt) > 4 - BRL(B_VenClampClosed)=TRUE Some possible explanations why the error has occurred: - The venous clamp is stucked in closed position - The clamp driver board is broken (transmitter-receiver) - Protective U board broken (R47, IC45, IC20, Q7, Q8, IC46, IC41, IC7) - Control U board broken (IC24)

C COFB 088 072

VENOUS CLAMP TEST ERROR, CLAMP NOT CLOSED (U P) Unconditional error, blood pump not available General description of conditions for occurring: - U P can not close the venous clamp. Technical description of conditions for occurring: - PRI(PI_VClampPCloseErrCnt) > 10 - BRL(B_VenClampClosed)=FALSE Some possible explanations why the error has occurred: - The venous clamp is stucked in open position - The clamp driver board is broken (transmitter-receiver) - Protective U board broken (R47, IC45, IC20, Q8, IC41)

C COFB 088 073

VENOUS CLAMP TEST ERROR, CLAMP NOT CLOSED (U W) Unconditional error, blood pump not available General description of conditions for occurring: - U W can not close the venous clamp.



75 (115)

Technical description of conditions for occurring: - PRI(PI_VClampWCloseErrCnt) > 10 - BRL(B_VenClampClosed)=FALSE Some possible explanations why the error has occurred: - The venous clamp is stucked in open position - The clamp driver board is broken (transmitter-receiver) - Protective U board broken (R47, IC45, IC20, Q7, IC46, IC7) C COFB 088 074

ARTERIAL CLAMP TEST ERROR Unconditional error, blood pump not available General description of conditions for occurring: The arterial clamp test failed, either when opening or when closing the clamp Technical description of conditions for occurring: - BRL(B_ArtClampTestErr)= TRUE Some possible explanations why the error has occurred: - The clamp is mechanically jammed or blocked - Bad connection between clamp unit and the cabling - The clamp unit is broken - Protective U board broken (IC45, Q6, V7) - Control U board broken (IC24)

C COFF 088 075

HEATER TEST ERROR, HEATER ENERGIZED Unconditional error, blood pump not available General description of conditions for occurring: - The heater is still energized after U C has regulated 0% dutycycle Technical description of conditions for occurring: - PRI(PI_HeaterOff1ErrCnt) > 3 - Signal PMAINS is high (+5V) Some possible explanations why the error has occurred: - P931 and P932 on heater relay board are incorrectly positioned - The heater relay board is broken (K1) - The heater relay board is broken (IC1and components) - Protective driver board broken (IC25, IC 28) - Control U board is broken (IC21)

C COFF 088 076

HEATER TEST ERROR, HEATER ENERGIZED Unconditional error, blood pump available General description of conditions for occurring: - The heater is still energized when U P has turned the heater relay off. Technical description of conditions for occurring: - PRI(PI_HeaterOff2ErrCnt) > 3 - Signal PMAINS is high (+5V) Some possible explanations why the error has occurred: - The FM I/O board is broken (Q1, R8) - The heater relay board is broken (IC1 and components) - Protective driver board broken (IC3, IC25, IC 28)

76 (115)



C COFF 088 077

HEATER TEST ERROR, HEATER ENERGIZED Unconditional error, blood pump available General description of conditions for occurring: - The heater is still energized after U C has shut off the heater relay. Technical description of conditions for occurring: - PRI(PI_HeaterOff3ErrCnt) > 3 - Signal PMAINS is high (+5V) Some possible explanations why the error has occurred: - The FM I/O board is broken (Q2) - The control driver board is broken (IC24) - The heater relay board is broken (IC1 and components) - The protective driver board is broken (IC25, IC 28)

C COFF 088 078

HEATER TEST ERROR, HEATER ENERGIZED Unconditional error, blood pump available General description of conditions for occurring: - The heater is still energized after INVA has been closed. No flow through the flow switch. Technical description of conditions for occurring: - PRI(PI_HeaterOff4ErrCnt) > 3 - Signal PMAINS is high (+5V) Some possible explanations why the error has occurred: - The flow switch is stucked in upper position - The FM I/O board is broken (Q4) - The heater relay board is broken (IC1 and components) - Protective driver board broken (IC25, IC 28)

C COFF 088 079

HEATER TEST ERROR, HEATER NOT ENERGIZED Unconditional error, blood pump available General description of conditions for occurring: - The heater is not energized when there is flow through to the monitor and U C runs the heater with duty cycle 40 %. Technical description of conditions for occurring: - PRI(PI_HeaterOn1ErrCnt) > 3 - Signal PMAINS is low (Zero volt) Some possible explanations why the error has occurred: - Broken fuse in AC/DC unit - Control U board broken (IC21) - Control driver board is broken (IC24) - Float stucked in lower position - Flow switch broken - FM I/O board is broken (Q1, Q2, Q3, Q4, R2) - Heater relay board is not connected - Protective U board is broken (signal PHEEN) - Protective driver board broken (IC25, IC 28) - The heater relay board is broken (K1, K2, V1, IC1 and components)

C COFF 088 080


HEATER TEST ERROR, HEATER NOT ENERGIZED Unconditional error, blood pump available


77 (115)

General description of conditions for occurring: - The heater is not energized when there is flow through to the monitor and U C runs the heater with duty cycle 40 %. Technical description of conditions for occurring: - PRI(PI_HeaterOn2ErrCnt) > 3 - Signal PMAINS is low (Zero volt) Some possible explanations why the error has occurred: - Broken fuse in AC/DC unit - Control U board broken (IC21) - Control driver board is broken (IC24) - Float stucked in lower position - Flow switch broken - FM I/O board is broken (Q1, Q2, Q3, Q4, R2) - Heater relay board is not connected - Protective U board is broken (signal PHEEN) - Protective driver board broken (IC25, IC 28) - The heater relay board is broken (K1, K2, V1, IC1 and components) C COFF 088 081

HEATER TEST ERROR, HEATER NOT ENERGIZED Unconditional error, blood pump available General description of conditions for occurring: - The heater is not energized when there is flow through to the monitor and U C runs the heater with duty cycle 40 %. Technical description of conditions for occurring: - PRI(PI_HeaterOn3ErrCnt) > 3 - Signal PMAINS is low (Zero volt) Some possible explanations why the error has occurred: - Broken fuse in AC/DC unit - Control U board broken (IC21) - Control driver board is broken (IC24) - Float stucked in lower position - Flow switch broken - Flow switch in incorrect position (should be mounted close to lower silicon connector) - FM I/O board is broken (Q1, Q2, Q3, Q4, R2) - Heater relay board is not connected - Protective U board is broken (signal PHEEN) - Protective driver board broken (IC25, IC 28) - The heater relay board is broken (K1, K2, V1, IC1 and components)

C COFF 088 082

HEATER TEST ERROR, HEATER NOT ENERGIZED Unconditional error, blood pump available General description of conditions for occurring: - The heater is not energized when there is flow through to the monitor and U C runs the heater with duty cycle 40 %. Technical description of conditions for occurring: - PRI(PI_HeaterOn4ErrCnt) > 3 - Signal PMAINS is low (Zero volt) Some possible explanations why the error has occurred:

78 (115)



- Broken fuse in AC/DC unit - Control U board broken (IC21) - Control driver board is broken (IC24) - Float stucked in lower position - Flow switch broken - Flow switch in incorrect position (should be mounted close to lower silicon connector) - FM I/O board is broken (Q1, Q2, Q3, Q4, R2) - Heater relay board is not connected - Protective U board is broken (signal PHEEN) - Protective driver board broken (IC25, IC 28) - The heater relay board is broken (K1, K2, V1, IC1 and components) C COFF 088 083

HEATER TEST ERROR, HEATER NOT ENERGIZED Unconditional error, blood pump available General description of conditions for occurring: - The heater is not energized when there is flow through to the monitor and U C runs the heater with duty cycle 40 %. Technical description of conditions for occurring: - PRI(PI_HeaterOn5ErrCnt) > 3 - Signal PMAINS is low (Zero volt) Some possible explanations why the error has occurred: - Broken fuse in AC/DC unit - Control U board broken (IC21) - Control driver board is broken (IC24) - Float stucked in lower position - Flow switch broken - Flow switch in incorrect position (should be mounted close to lower silicon connector) - FM I/O board is broken (Q1, Q2, Q3, Q4, R2) - Heater relay board is not connected - Protective U board is broken (signal PHEEN) - Protective driver board broken (IC25, IC 28) - The heater relay board is broken (K1, K2, V1, IC1 and components)

C COFF 088 084

FAILURE WHEN REGULATING HPG PRESSURE (DIVA/TAVA TEST) Unconditional error, blood pump available General description of conditions for occurring: - No “pressure achieved” acknowledge signal sent to U P from U C - This error code is not used in program version 3.00 and later Technical description of conditions for occurring: - PRI(PI_ValveNoAchErrCnt) > 4 Some possible explanations why the error has occurred: - Leakage between the dialysis fluid tubes and the machine - Leakage between the dialyzer connectors and the by unit - Broken HPG transducer - Broken control driver board (Q12 and components) - Broken control U board (IC32)

C COFF 088 085


NO CONDUCTIVITY VALUE SENT TO U P (LOW TEST)


79 (115)

Unconditional error, blood pump available General description of conditions for occurring: - No conductivity value sent from U C to U P during conductivity test Technical description of conditions for occurring: - PRI(PI_CondNoAchLowErrCnt) > 0 - The low test has been running for 60 seconds with no value sent from U C Some possible explanations why the error has occurred: - Air in fluid path - Broken U C conductivity cell (cell B) - Broken MM I/O board - Broken control driver board - Broken protective U board (IC50) - Broken control U board (IC5, IC4, IC1 and components) C COFF 088 086

UNSTABLE LEVEL IN DEAIRATING CHAMBER Unconditional error, blood pump available General description of conditions for occurring: - The level in deairating chamber is unstable. - The level should have been high Technical description of conditions for occurring: - PRI(PI_ValveBubLevelErrCnt) > 10 (UFD-kit not installed) - PRI(PI_ValveBubLevelErrCnt) > 65 ( UFD-kit installed) - AK95P.U_P.SUP.MEAS.MEASURE_INPUT.bubble (log. variable) Some possible explanations why the error has occurred: - Air leakage - Broken level detector - EVVA is not open or malfunctioning - TAVA is not closed or malfunctioning - IC 28 on protective driver board broken - FIVA is broken (if the UFD-kit is preseted) - UFD is not preseted, despite the ultrafilter and FIVA is mounted

C COFF 088 087

FAILURE WHEN REGULATING HPG PRESSURE (DIVA/TAVATEST) Unconditional error, blood pump available General description of conditions for occurring: - No “pressure achieved” acknowledge signal sent to U P from U C - U is regulating HPG pressure to -200mmHg Technical description of conditions for occurring: - PRI(PI_ValveNoAchLow1ErrCnt) > 4 Some possible explanations why the error has occurred: - Air in fluid. Check for leakage - Leakage between the dialysis fluid tubes and the machine - Leakage between the dialyzer connectors and the by unit - Broken HPG transducer - Broken control driver board (Q12 and components) - Broken control U board (IC32)

80 (115)



C COFF 088 088

FAILURE WHEN REGULATING HPG PRESSURE (DIVA/TAVA TEST) Unconditional error, blood pump available General description of conditions for occurring: - No “pressure achieved” acknowledge signal sent to U P from U C - U is regulating HPG pressure to +200mmHg Technical description of conditions for occurring: - PRI(PI_ValveNoAchHigh1ErrCnt) > 2 Some possible explanations why the error has occurred: - Air in fluid. Check for leakage - Leakage between the dialysis fluid tubes and the machine - Leakage between the dialyzer connectors and the by unit - Broken HPG transducer - Broken control driver board (Q12 and components) - Broken control U board (IC32)

C COFF 088 089

FAILURE WHEN REGULATING HPG PRESSURE (DIVA/TAVA TEST) Unconditional error, blood pump available General description of conditions for occurring: - No “pressure achieved” acknowledge signal sent to U P from U C - U is regulating HPG pressure to -200mmHg Technical description of conditions for occurring: - PRI(PI_ValveNoAchLow2ErrCnt) > 2 Some possible explanations why the error has occurred: - Air in fluid. Check for leakage - Leakage between the dialysis fluid tubes and the machine - Leakage between the dialyzer connectors and the by unit - Broken HPG transducer - Broken control driver board (Q12 and components) - Broken control U board (IC32)

C COFF 088 090

FAILURE WHEN REGULATING HPG PRESSURE (DIVA/TAVA TEST) Unconditional error, blood pump available General description of conditions for occurring: - No “pressure achieved” acknowledge signal sent to U P from U C - U is regulating HPG pressure to +200mmHg Technical description of conditions for occurring: - PRI(PI_ValveNoAchHigh2ErrCnt) > 2 Some possible explanations why the error has occurred: - Air in fluid. Check for leakage - Leakage between the dialysis fluid tubes and the machine - Leakage between the dialyzer connectors and the by unit - Broken HPG transducer - Broken control driver board (Q12 and components) - Broken control U board (IC32)



81 (115)

C COFF 088 091

TOO HIGH TEMPERATURE AT START-UP Unconditional error, blood pump available General description of conditions for occurring: - U P could not measure a temp below 45C (15 minute measure time) Technical description of conditions for occurring: - PRI(PI_TempStartHiErrCnt) > 0 - AK95P.U_P.SUP.MEAS.AD_INPUT.tempValue > 45C Some possible explanations why the error has occurred: - Broken U P temperature transducer - Broken MM 95 board - Broken protective driver board

C COFF 088 092

FAILURE WHEN REGULATING TEMPERATURE, HIGH TEMPERATURE TEST General description of conditions for occurring: - U C has not been able to regulate the temperature Technical description of conditions for occurring: - PRI(PI_TempNoAchHigh1ErrCnt) > 0 - Unstable temperature in conductivity cell B, (FRI(FI_MM90CondTempB) Some possible explanations why the error has occurred: - Air in fluid path - Unstable fluid flow or unstable fluid pressure (check PR2) - Broken heater relay unit

C COFF 088 093

FAILURE WHEN REGULATING TEMPERATURE, HIGH TEMPERATURE TEST General description of conditions for occurring: - U C has not been able to regulate the temperature (during retest) Technical description of conditions for occurring: - PRI(PI_TempNoAchHigh2ErrCnt) > 0 - Unstable temperature in conductivity cell B, (FRI(FI_MM90CondTempB) Some possible explanations why the error has occurred: - Air in fluid path - Unstable fluid flow or unstable fluid pressure (check PR2) - Broken heater relay unit

C COFF 088 094

FAILURE WHEN REGULATING TEMPERATURE, LOW TEMPERATURE TEST General description of conditions for occurring: - U C has not been able to regulate the temperature Technical description of conditions for occurring: - PRI(PI_TempNoAchLowErrCnt) > 0 - Unstable temperature in conductivity cell B, FRI(FI_MM90CondTempB)

82 (115)



Some possible explanations why the error has occurred: - Air in fluid path - Unstable fluid flow or unstable fluid pressure (check PR2) - Broken heater relay unit C COFF 088 095

UNSTABLE CONDUCTIVITY (HIGH TEST) Unconditional error, blood pump available General description of conditions for occurring: - No conductivity value sent from U C to U P due to unstable signal Technical description of conditions for occurring: - PRI(PI_CondNoAchHighErrCnt) > 0 - Unstable cond. value in conductivity cell B, FRI(FI_MM90CONDB) Some possible explanations why the error has occurred: - Air in fluid path - Broken U C conductivity cell (cell B) - Broken MM I/O board - Broken control driver board

C COFB 088 096

BATTERY TEST ERROR 4 TIMES IN SUCCESSION Unconditional error, blood pump not available General description of conditions for occurring: - Protective system has measured too low battery voltage at least 4 times in succession Technical description of conditions for occurring: - Measured voltage < 7.5 V (no load on the battery) - Measured voltage < 6.0 V (battery loaded with 50 mA)

C COFF 088 097

COMMUNICATION FAILURE DURING VALVES CURRENT TEST Unconditional error, blood pump not available General description of conditions for occurring: - U P has sent a request to U C to set the status of BYVA and DIVA in a specified way. U P has not got any confirmation of the request. Technical description of conditions for occurring: - PRI(PI_CurrVaConfirmErrCnt) > 5 - U P didn’t receive any confirm signal. Some possible explanations why the error has occurred: - Broken U C board - Broken U P board

C COFF 088 098

CLOSE FAILURE DURING VALVES CURRENT TEST Unconditional error, blood pump not available General description of conditions for occurring: - The valves DIVA, BYVA, TAVA and EVVA should be closed but the measured valve current indicates that at least one of them is open. Technical description of conditions for occurring: - PRI(PI_CurrVaCloseErrCnt) > 2



83 (115)

- The valve current indicates that some valve is open. Some possible explanations why the error has occurred: - Broken Control driver board - Broken Protective driver board C COFF 088 099

DIVA OPEN FAILURE DURING VALVES CURRENT TEST Unconditional error, blood pump not available General description of conditions for occurring: - DIVA should be open but the measured valve current indicates that it is closed. Technical description of conditions for occurring: - PRI(PI_CurrVaOpenDIVAErrCnt) > 2 - The valve current indicates that DIVA is closed. Some possible explanations why the error has occurred: - Broken DIVA - Broken Control driver board - Broken Protective driver board

C COFF 088 100

DIVA P CLOSED FAILURE DURING VALVES CURRENT TEST Unconditional error, blood pump not available General description of conditions for occurring: - DIVA should be closed but the measured valve current indicates that it is open. U C wants to have DIVA open. U P wants to have DIVA closed. Technical description of conditions for occurring: PRI(PI_CurrVaOpenDIVACErrCnt) > 2 The valve current indicates that DIVA is open. Some possible explanations why the error has occurred: Broken Control driver board Broken Protective driver board

C COFF 088 101

DIVA C CLOSED FAILURE DURING VALVES CURRENT TEST Unconditional error, blood pump not available General description of conditions for occurring: - DIVA should be closed but the measured valve current indicates that it is open. U C wants to have DIVA closed. U P wants to have DIVA open. Technical description of conditions for occurring: - PRI(PI_CurrVaOpenDIVAPErrCnt) > 2 - The valve current indicates that DIVA is open. Some possible explanations why the error has occurred: - Broken Control driver board - Broken Protective driver board

C COFF 088 102

BYVA OPEN FAILURE DURING VALVES CURRENT TEST Unconditional error, blood pump not available General description of conditions for occurring: - BYVA should be open but the measured valve current indicates that it is closed.

84 (115)



Technical description of conditions for occurring: - PRI(PI_CurrVaOpenBYVAErrCnt) > 2 - The valve current indicates that BYVA is closed. Some possible explanations why the error has occurred: - Broken BYVA - Broken Control driver board - Broken Protective driver board C COFF 088 103

BYVA C OPEN FAILURE DURING VALVES CURRENT TEST Unconditional error, blood pump not available General description of conditions for occurring: - BYVA should be open but the measured valve current indicates that it is closed. U C wants to have BYVA open. U P wants to have BYVA closed. Technical description of conditions for occurring: - PRI(PI_CurrVaOpenBYVACErrCnt) > 2 - The valve current indicates that BYVA is closed. Some possible explanations why the error has occurred: - Broken BYVA - Broken Control driver board - Broken Protective driver board

C COFF 088 104

BYVA P OPEN FAILURE DURING VALVES CURRENT TEST Unconditional error, blood pump not available General description of conditions for occurring: - BYVA should be open but the measured valve current indicates that it is closed. U C wants to have BYVA closed. U P wants to have BYVA open. Technical description of conditions for occurring: - PRI(PI_CurrVaOpenBYVAPErrCnt) > 2 - The valve current indicates that BYVA is closed. Some possible explanations why the error has occurred: - Broken BYVA - Broken Control driver board - Broken Protective driver board

C COFF 088 105

TAVA OPEN FAILURE DURING VALVES CURRENT TEST Unconditional error, blood pump not available General description of conditions for occurring: - TAVA should be open but the measured valve current indicates that it is closed. Technical description of conditions for occurring: - PRI(PI_CurrVaOpenTAVAErrCnt) > 2 - The valve current indicates that TAVA is closed. Some possible explanations why the error has occurred: - Broken TAVA - Broken Protective driver board

C COFF 088 106


EVVA OPEN FAILURE DURING VALVES CURRENT TEST


85 (115)

Unconditional error, blood pump not available General description of conditions for occurring: - EVVA should be open but the measured valve current indicates that it is closed. Technical description of conditions for occurring: - PRI(PI_CurrVaOpenEVVAErrCnt) > 2 - The valve current indicates that EVVA is closed. Some possible explanations why the error has occurred: - Broken EVVA - Broken Protective driver board C COFF 088 107

CASE ERROR Transient error General description of conditions for occurring: - Internal software error.

C COFF 088 108

CONDUCTIVITY TEST ERROR, CONDUCTIVITY IN U C UNSTABLE (HIGH CONDUCTIVITY TEST) Unconditional error, blood pump available General description of conditions for occurring: - The conductivity value measured in U C is not stable in the high conductivity test Technical description of conditions for occurring: - PRI (PI_CondCHighStableErrCnt) > 4 Some possible explanations why the error has occurred: - Air in fluid path - Conductivity cell B is broken or uncalibrated

C COFF 088 109

CONDUCTIVITY TEST ERROR, GENERAL ERROR (HIGH CONDUCTIVITY TEST) Unconditional error, blood pump available General description of conditions for occurring: - The high conductivity test has not ed within the 20 minutes time limit Technical description of conditions for occurring: - PRI (PI_CondTimeOutErrCnt) > 0 Some possible explanations why the error has occurred: - Air in fluid path - Conductivity cell B is broken or uncalibrated - Conductivity cell P is broken or uncalibrated - Conductivity cell A is broken or uncalibrated

C COFF 088 110

DRVA OPEN FAILURE DURING VALVES CURRENT TEST Unconditional error, blood pump not available General description of conditions for occurring: - DRVA should be open but the measured valve current indicates that it is

86 (115)



closed. Technical description of conditions for occurring: - PRI(PI_CurrVaOpenDRVAErrCnt) > 2 - The valve current indicates that DRVA is closed. Some possible explanations why the error has occurred: - Broken DRVA - Broken Protective driver board C COFF 088 111

REVA OPEN FAILURE DURING VALVES CURRENT TEST Unconditional error, blood pump not available General description of conditions for occurring: - REVA should be open but the measured valve current indicates that it is closed. Technical description of conditions for occurring: - PRI(PI_CurrVaOpenREVAErrCnt) > 2 - The valve current indicates that REVA is closed. Some possible explanations why the error has occurred: - Broken REVA - Broken Protective driver board

C COFF 088 112

ZEVA OPEN FAILURE DURING VALVES CURRENT TEST Unconditional error, blood pump not available General description of conditions for occurring: - ZEVA should be open but the measured valve current indicates that it is closed. Technical description of conditions for occurring: - PRI(PI_CurrVaOpenZEVAErrCnt) > 2 - The valve current indicates that ZEVA is closed. Some possible explanations why the error has occurred: - Broken ZEVA - Broken Protective driver board

C COFF 088 113

RIVA OPEN FAILURE DURING VALVES CURRENT TEST Unconditional error, blood pump not available General description of conditions for occurring: - RIVA should be open but the measured valve current indicates that it is closed. Technical description of conditions for occurring: - PRI(PI_CurrVaOpenRIVAErrCnt) > 2 - The valve current indicates that RIVA is closed. Some possible explanations why the error has occurred: - Broken RIVA - Broken Protective driver board

C COFF 088 114

INVA OPEN FAILURE DURING VALVES CURRENT TEST Unconditional error, blood pump not available General description of conditions for occurring: - INVA should be open but the measured valve current indicates



87 (115)

that it is closed. Technical description of conditions for occurring: - PRI(PI_CurrVaOpenINVAErrCnt) > 2 - The valve current indicates that INVA is closed. Some possible explanations why the error has occurred: - Broken INVA - Broken Protective driver board

C COFF 088 115

CHEMICAL VALVE LEAKAGE TEST The negative pressure of -350 mmHg is not accomplished. Probable cause is a huge air leakage somewhere between INVA and ZEVA. Other causes could be a malfunctioning HPG sensor or a malfunctioning suction pump.

C COFF 088 116

The trapped pressure has increased above the negative pressure of -250 mmHg during the stabilization period of 4 seconds. Probable cause is a huge air leakage somewhere between INVA and ZEVA.

C COFF 088 117

The trapped pressure has decreased more then 10 mmHg within 10 seconds. Probable cause is a minor air leakage in ZEVA, BYVA, RIVA or degassing chamber.

C COFF 088 118

The trapped pressure has increased more then 10 mmHg within 10 seconds. Probable cause is a minor air leakage INVA, AIVA, CBVA or fluid path is leaking.

C COFF 088 119

The trapped pressure has increased above the negative pressure of -250 mmHg during the stabilization period of 4 seconds. Probable cause is a huge air leakage somewhere between INVA and ZEVA.

C COFF 088 120

The trapped pressure has decreased more then 10 mmHg within 10 seconds. Probable cause is minor air leakage in ZEVA, BYVA, RIVA or degassing chamber.

C COFF 088 121

The trapped pressure has increased more then 10 mmHg within 10 seconds. Probable cause is a minor air leakage in INVA, AIVA, CHVA or fluid path is leaking.

C COFB 088 122

Control venous pressure transducer and protective venous pressure transducer differs more then 10 mmHg during high venous pressure test. Probable cause is malfunctioning sensors or incorrect calibrated sensors.

C COFB 088 123

Arterial clamp is set NOT installed but is detected by Fch as present (Clamp is not closed).

C COFB 088 124

Dialysis machine in Single Needle mode but arterial clamp is not installed .

C COFB 088 125

Assisted Priming Alt 1 contains auto venous drip chamber adjustment but no arterial clamp is installed.

C COFB 088 126

Assisted Priming Alt 2 contains auto venous drip chamber

88 (115)



adjustment but no arterial clamp is installed. C COFB 088 127

Assisted Priming Alt 3 contains auto venous drip chamber adjustment but no arterial clamp is installed.

C COFF 088 128

CHVA does not open correctly. Probable cause is broken or unconnected valve.

C CO 089, Real Time Clock C CO 089 000


C CO 089 001

REAL TIME CLOCK ERROR (READ) General description of conditions for occurring: - I2C error occurred while reading from the real time clock/calendar PCF8573. The current time and date in the machine may be incorrect. Technical description of conditions for occurring: - Real time clock has returned error message Some possible explanations why the error has occurred: - Real time clock IC47 (and components) on protective driver board broken

C CO 089 002

REAL TIME CLOCK ERROR (WRITE) General description of conditions for occurring: - I2C error occurred while writing to the real time clock/calendar. Technical description of conditions for occurring: - Real time clock has returned error message Some possible explanations why the error has occurred: - Real time clock IC47 (and components) on protective driver board broken

C CO 089 003

REAL TIME CLOCK ERROR (SAVE) General description of conditions for occurring: - An error occurred while saving the year (EEI_TimeNowYear) in the preset variables. The year value may be incorrect the next time the machine is started. Some possible explanations why the error has occurred: - Broken SAFE memory

C CO 089 004

REAL TIME CLOCK ERROR (AUTO START) General description of conditions for occurring: - During the start-up, the function detected that the alarm was switched ON in the PCF8573, but there was no valid auto-start status saved in the safe memory tables. No autoheat or autorinse will be started.



89 (115)

Some possible explanations why the error has occurred: - Broken SAFE memory

C CO 090, Protective Vpr Limit Set C CO 090 000


C CO 093, Disinfection Timer C CO 093 000


C CO 094, Decalcification Timer C CO 094 000


CO 097, Menu handling C CO 097 000

CASE ERROR General description of conditions for occurring: - Internal software error

C CO 097 001

CASE ERROR General description of conditions for occurring: - Internal software error

C FRFF 088, Functional Check Restart The following error codes are “silent error codes”. If a test corresponding to each of the error codes fails, the fluid monitor functional check will be restarted and the error code C FRFF XXX XXX will be stored in the error code buffer. If the test fails a second time, the error code C COFF XXX XXX will appear, together with buzzer alarm and spanner key light.

C FRFF 088 055

FUNCTIONAL CHECK RESTARTED

General description of conditions for occurring: -See C COFF 088 055

C FRFF 088 056

90 (115)





C FRFF 088 061



C FRFF 088 065



C FRFF 088 086



C FRFF 088 088

FUNCTIONAL CHECK RESTARTED General description of conditions for occurring: -See C COFF 088 088

C FRFF 088 092

FUNCTIONAL CHECK RESTARTED General description of conditions for occurring: -See C COFF 088 092

C FRFF 006, Functional Check Restart The following error codes are “silent error codes”. If a test corresponding to each of the error codes fails, the fluid monitor functional check will be restarted and the error code C FRFF XXX XXX will be stored in the error code buffer. If the test fails a second time, the error code C COFF XXX XXX will appear, together with buzzer alarm and spanner key light.

C FRFF 006 003

FUNCTIONAL CHECK RESTARTED General description of conditions for occurring: -See C CFF 006 003

C Cx 000 xxx, Transition Controller C Cx 000 001 C Cx 000 002 C Cx 000 003

Pxxx ttt Pxxx yyy Pxxx ttt


Process nr xxx out of range in transition test State nr yyy out of range Test nr ttt out of range in transition test


91 (115)

C Cx 000 004 C Cx 000 005 C Cx 000 006

P000 xxx Pxxx yyy Pxxx yyy

C Cx 000 007 C Cx 000 008 C Cx 000 009 C Cx 000 010 C Cx 000 011

Pxxx yyy Pxxx yyy Pxxx yyy Pxxx yyy Pxxx yyy

C Cx 000 012 C Cx 000 013 C Cx 000 014

Pxxx yyy P000 fff Pxxx yyy

C Cx 000 015

jjjj iii

C Cx 000 016 C Cx 000 017

P000 fff jjjj iii

Process state shadow table corrupt in process xxx Process attempt to assume non-defined state yyy State yyy attempt to control process at own or higher level State yyy attempt to control non-defined process State yyy attempt to control non-defined function State yyy attempt to duplicate process control State yyy attempt to duplicate function control State yyy attempt to reference non-defined event control State yyy attempt to set non-defined event mode Non-controlled function fff State yyy attempt to set non-existant output cross reference Crossreference iii references non-existant logical output jjjj Function shadow table corrupt in function fff Logical output corrupt. Crossreference iii references to logical output table. jjjj references to index in lit file. Unconditional error, blood pump available if x=”F” or “O” Some possible explanations why the above error has occurred: - Internal software error

(x = Transition controller identifier [B,F,O] ) (xxx = Process number) (yyy = State number)

92 (115)



C CSYS, Ctask in U C C CSYS 000 000

CASE ERROR O/FM_MAINSTATEFCN. Unconditional error, blood pump not available Some possible explanations why the error has occurred: - Internal software error

C CSYS 000 001

ADC_TASK COULD NOT BE STARTED. Unconditional error, blood pump not available Some possible explanations why the error has occurred: - Internal software error

C CSYS 000 002

FMTRC TASK COULD NOT BE STARTED. Unconditional error, blood pump not available Some possible explanations why the error has occurred: - Internal software error

C CSYS 000 003

BMTRC TASK COULD NOT BE STARTED. Unconditional error, blood pump not available Some possible explanations why the error has occurred: - Internal software error

C CSYS 000 004

OMTRC TASK COULD NOT BE STARTED. Unconditional error, blood pump not available Some possible explanations why the error has occurred: - Internal software error

C CSYS 000 005

FCN_TASK_0 COULD NOT BE STARTED. Unconditional error, blood pump not available Some possible explanations why the error has occurred: - Internal software error

C CSYS 000 006


C CSYS 000 007


C CSYS 000 008


C CSYS 000 009

FCN_TASK_4 COULD NOT BE STARTED. Unconditional error, blood pump not available Some possible explanations why the error has occurred:



93 (115)

- Internal software error C CSYS 000 010


C CSYS 000 011

PROGRAM VERSION ERROR, U C General description of conditions for occurring: - An illegal combination of PROMS were detected at start-up Some possible explanations why the error has occurred: - The U C EPROMS are not approved (in combination with P and W)

C CSYS 000 012

PROGRAM VERSION ERROR, U P General description of conditions for occurring: - An illegal combination of PROMS were detected at start-up Some possible explanations why the error has occurred: - The U P EPROMS are not approved (in combination with C and W)

C CSYS 000 013

PROGRAM VERSION ERROR, U W General description of conditions for occurring: - An illegal combination of PROMS were detected at start-up Some possible explanations why the error has occurred: - The U W EPROM is not approved (in combination with C and P)

C CSYS 000 014

PROGRAM VERSION ERROR, U C AND U P General description of conditions for occurring: - An illegal combination of PROMS were detected at start-up Some possible explanations why the error has occurred: - The U C and P EPROMS are not approved (in combination with W)

C CSYS 000 015

PROGRAM VERSION ERROR, U C AND U W General description of conditions for occurring: - An illegal combination of PROMS were detected at start-up Some possible explanations why the error has occurred: - The U C and W EPROMS are not approved (in combination with P)

C CSYS 000 016

PROGRAM VERSION ERROR, U P AND U W General description of conditions for occurring: - An illegal combination of EPROMS were detected at start-up Some possible explanations why the error has occurred: - The U P and W PROMS are not approved (in combination

94 (115)



with C) C CSYS 000 017

PROGRAM VERSION ERROR, SYSTEM SUBVERSION General description of conditions for occurring: - An illegal combination of PROMS were detected at start-up Some possible explanations why the error has occurred: - The U P and/or the U W PROM is not approved in combination with U C.

C CSYS 000 018

REMOTE START OF WRO FAILED Unconditional error, blood pump not available Some possible explanations why the error has occurred: -Internal software error

C CSYS 000 019


C CSYS 000 020

SUPERVISION TASK COULD NOT BE STARTED. Unconditional error, blood pump not available Some possible explanations why the error has occurred: - Internal software error

C CSYS 000 030

PROGRAM FLOW TIMEOUT General description of conditions for occurring: - A program flow timeout has been detected in U C. Some possible explanations why the error has occurred: - Internal software error

C CSYS 000 202

TASK TIME-OUT General description of conditions for occurring: - The BMTrc_Task is not running Some possible explanations why the error has occurred: - Internal software error

C CSYS 000 203

TASK TIME-OUT General description of conditions for occurring: - The FMTrc_Task is not running Some possible explanations why the error has occurred: - Internal software error

C CSYS 000 204

TASK TIME-OUT General description of conditions for occurring: - The OMTrc_Task is not running Some possible explanations why the error has occurred:



95 (115)

- Internal software error C CSYS 000 205

TASK TIME-OUT General description of conditions for occurring: - The Fcn_Task_0 is not running Some possible explanations why the error has occurred: - Internal software error

C CSYS 000 206


C CSYS 000 207


C CSYS 000 208


C CSYS 000 209


C CSYS 000 210


C CSYS 000 210


C CSYS 000 211

96 (115)

TASK TIME-OUT



General description of conditions for occurring: - The AdcTask is not running Some possible explanations why the error has occurred: - Internal software error C CSYS 000 250

TASK TIME-OUT General description of conditions for occurring: - The ComTask is not running Some possible explanations why the error has occurred: - Internal software error

C CSYS 000 251

TASK TIME-OUT General description of conditions for occurring: - The SDTLog_Task is not running Some possible explanations why the error has occurred: - Internal software error

C CSYS 000 252

TASK TIME-OUT General description of conditions for occurring: - The DispatchTask is not running Some possible explanations why the error has occurred: - Internal software error

C CSYS 000 300

PARALLEL COMMUNICATION STOPPED General description of conditions for occurring: - The parallel communication between U C and U P has stopped Some possible explanations why the error has occurred: - Internal software error

C CSYS 000 301

PARALLEL COMMUNICATION ERROR General description of conditions for occurring: - Too many send message errors Some possible explanations why the error has occurred: - Internal software error

C CSYS 000 302

PARALLEL COMMUNICATION ERROR General description of conditions for occurring: - Too many receive message errors Some possible explanations why the error has occurred: - Internal software error

C CSYS 000 401

COMMUNICATION HANDLING ERROR General description of conditions for occurring: - The communication handling is malfunctioning



97 (115)

Some possible explanations why the error has occurred: - Internal software error C CSYS 000 402

COMMUNICATION HANDLING ERROR General description of conditions for occurring: - The communication handling is malfunctioning Some possible explanations why the error has occurred: - Internal software error

C CSYS 000 403


98 (115)



C EBUF 000 000, Error Code Buffer C EBUF 000 000

ERROR CODE BUFFER CORRUPT General description of conditions for occurring: - The checksum protecting the error code buffer is corrupt. Restart the AK 96 Some possible explanations why the error has occurred: - Broken/corrupt Safe-RAM on control U board

C SYS, System Errors C SYS 000 000

DIVIDE ERROR, DIVISION BY 0, IN U C Transient error Some possible explanations why the error has occurred: - Internal software error

C SYS 000 001

SINGLE STEP TRAP, U C Some possible explanations why the error has occurred: - Internal software error - Corrupt memory

C SYS 000 002

NMI (NON MASKABLE INTERRUPT) ERROR IN U C Some possible explanations why the error has occurred: - Internal software error

C SYS 000 003

BREAKPOINT IN U C Some possible explanations why the error has occurred: - Internal software error - Corrupt memory

C SYS 000 004

OVERFLOW IN U C Some possible explanations why the error has occurred: - Internal software error

C SYS 000 005

ARRAY BOUNDS TRAP IN U C Some possible explanations why the error has occurred: - Internal software error

C SYS 000 006

UNUSED OPCODE ERROR IN U C Some possible explanations why the error has occurred: - Internal software error - Corrupt memory

C SYS 000 007

ESCAPE OPCODE ERROR IN U C Some possible explanations why the error has occurred: - Internal software error - Corrupt memory



99 (115)

C SYS 000 008

RESERVED VECTOR IN U C Some possible explanations why the error has occurred: - Internal software error

C SYS 001 000

FLOAT ILLEGAL OPCODE IN U C Some possible explanations why the error has occurred: - Internal software error

C SYS 001 001

FLOAT REAL OVERFLOW IN U C Some possible explanations why the error has occurred: - Internal software error

C SYS 001 002

FLOAT INTEGER OVERFLOW IN U C Some possible explanations why the error has occurred: - Internal software error

C SYS 001 003

UNDEFINED MESSAGE IN U C Some possible explanations why the error has occurred: - Internal software error

100 (115)



P ENV, U P ENVIRONMENT P ENV 001 001

DEAIRATING CHAMBER ERROR General description of conditions for occurring: - The level detected in deairating chamber was both high AND low - This was detected for more than 5 seconds. Some possible explanations why the error has occurred: - IC 28 on protective driver board broken - Broken level switch

P ENV 001 002

DEAIRATING CHAMBER HIGH LEVEL ERROR General description of conditions for occurred: -The level in the deairating chamber has been high for more than 45 seconds during treatment Some possible explanations why the error has occurred: - EVVA leakage. - The tube between deairating chamber and EVVA is leaking. - Level detector could be stuck. -There has been a very high positive pressure in the chamber. This pressure is > 300 mmHg.

P ENV 002 001

BPM TASK ERROR Some possible explanations why the error has occurred: - Internal software error

P ENV 002 002

BPM COMMUNICATION ERROR Some possible explanations why the error has occurred: - Internal software error

P ENV 002 003


P ENV 002 004


P ENV 003 001

WRITE ERROR, LOUDSPEAKER Some possible explanations why the error has occurred: - Broken Protective Driver board. - Default preset has not been made.

P ENV 003 002

READ ERROR, LOUDSPEAKER Some possible explanations why the error has occurred: - Broken Protective Driver board. - Default preset has not been made.

P ENV 003 003

COMMUNICATION FAILURE, LOUDSPEAKER Some possible explanations why the error has occurred: - Broken Protective Driver board.



101 (115)

- Default preset has not been made.

P MEM, U P system P MEM 000 xxx

CORRUPTION OF COMMON CODEPAGE Common codepage is char number 0 .. 127 xxx = the number of the character

P MEM 001 xxx

CORRUPTION OF CODEPAGE 1 Codepage 1 is Western fonts xxx = the number of the character

P MEM 002 xxx

CORRUPTION OF CODEPAGE 2 Codepage 2 is defined fonts a.k.a. Chinese fonts xxx = the number of the character

P MEM 003 xxx

CORRUPTION OF CODEPAGE 3 Codepage 3 is Big digits xxx = the number of the character

P MEM 004 xxx

CORRUPTION OF CODEPAGE 4 Codepage 4 is old Big digits xxx = the number of the character

P PHEP, Heparin Pump P PHEP 001 001

ESTIMATED AND MEASURED HEPARIN BOLUS VOLUME DIFFER TOO MUCH Conditional error, confirm by setting bolus volume and heparin flow rate to zero. General description of conditions for occurring: - The measured accumulated heparin bolus volume differ more than ±10% from the estimated accumulated bolus volume. Some possible explanations why the error has occurred: - The heparin pump encoder is broken - The heparin pump belt is broken - Bad connection between heparin pump encoder and BM I/O board - IC 5 on BM I/O board broken - IC 48 on protective U board broken - IC 29 or IC 34 on control driver board broken

P PHEP 001 002

ESTIMATED AND MEASURED HEPARIN VOLUME DIFFER TOO MUCH Conditional error, confirm by setting bolus volume and heparin flow rate to zero General description of conditions for occurring - The measured accumulated heparin volume differ more than 2 ml from the estimated accumulated volume. Some possible explanations why the error has occurred: - The heparin pump encoder is broken - The heparin pump belt is broken - Bad connection between heparin pump encoder and BM I/O board - IC 5 on BM I/O board broken - IC 48 on protective U board broken - IC 29 or IC 34 on control driver board broken

102 (115)



P PHEP 001 003

ACCUMULATED HEPARIN VOLUME IN CONTROL SYSTEM AND PROTECTIVE SYSTEM DIFFER TOO MUCH Conditional error, confirm by setting bolus volume and heparin flow rate to zero General description of conditions for occurring - The accumulated heparin volume in control system and protective system differ more than ± 1 ml.

P POW, Power ON/OFF Functions P POW 001 001

PLD ERROR General description of conditions for occurring: PLD error at power up. Once every 50 ms the REMO signal (REMOVFY) is checked. If it is active during 100 loops (i.e. 5 seconds) then this error code is issued and an ON/OFF key activation is started. (The PONKY signal is set until REMOVFY disappears, then the PONKY signal is reset.) Some possible explanations why the error has occurred: - Broken protective driver board (IC 16)

P PPR, Program Flow (U P) P PPR 000 xxx

PROGRAM FLOW ERROR General description of conditions for occurring: - A program flow error was detected by U P Some possible explanations why the error has occurred: - Internal software error



103 (115)

P PSYS, System errors in U P P PSYS 000 001

LOW RESOLUTION DISPLAY USED WITH CHINESE LANGUAGE General description of conditions for occurring: It is not possible to use Chinese language together with the low resolution display (240 x 64 pixels). The Display needs to be exchanged in order to use Chinese language.

P PSYS 000 401


P PSYS 000 402


P PSYS 000 403


P PSYS 001 001

HIGH RESOLUTION DISPLAY USED WITH U P 16 MHz PROCESSOR General description of conditions for occurring: It is not possible to run the high resolution display (480 x 128 pixels) with U P 16 MHz clock frequency, the U P U board needs to be exchanged.

104 (115)



P PREC, Recovery Functions P PREC 000 000

SAFE-RAM CHECKSUM ERROR Transient error General description of conditions for occurring: Checksum error in both recovery banks, detected at startup. Some possible explanations why the error has occurred: - Broken U P safe-RAM

P PREC 001 00x

SAFE-RAM CHECKSUM ERROR General description of conditions for occurring: Checksum error in recovery bank x, detected when writing new values. If this message is not followed by P PREC 002 000, the error was repaired by copying the values of the other recovery bank. Some possible explanations why the error has occurred: - Broken U P safe-RAM

P PREC 002 000

SAFE-RAM CHECKSUM ERROR Transient error General description of conditions for occurring: Checksum error in both recovery banks, detected when writing new values. The error could not be repaired. This error is preceded by the message P PREC 001 00x Some possible explanations why the error has occurred: - Broken U P safe-RAM



105 (115)

P PTRA, U P transducers P PTRA 000 100

ERROR READING PARAMETERS FROM BLOOD LEAK DETECTOR Unconditional error, blood pump not available General description of conditions for occurring: - An error occurred while reading transducer parameters during init (start-up). Some possible explanations why the error has occurred: - No connection between transducer board and FM I/O board - No connection between FM I/O board and protective driver board - Transducer board mounted in incorrect position on FM I/O board - Incorrect transducer ID. Please update transducer ID (I2C scan). - Transducer board is broken - Serial bus error on protective U board - Uncalibrated transducer. Please calibrate transducer - Broken FM I/O board

P PTRA 000 101

ERROR READING PARAMETERS FROM CONDUCTIVITY CELL P (COND) Unconditional error, blood pump not available General description of conditions for occurring: - An error occurred while reading transducer parameters during init (start-up). Some possible explanations why the error has occurred: - No connection between transducer board and protective driver board - Incorrect transducer ID. Please update transducer ID (I2C scan). - Transducer board is broken - Serial bus error on protective U board - Uncalibrated transducer. Please calibrate transducer

P PTRA 000 102

ERROR READING PARAMETERS FROM CONDUCTIVITY CELL P (TEMP) Unconditional error, blood pump not available General description of conditions for occurring: - An error occurred while reading transducer parameters during init (start-up). Some possible explanations why the error has occurred: - No connection between transducer board and protective driver board - Incorrect transducer ID. Please update transducer ID (I2C scan). - Transducer board is broken - Serial bus error on protective U board - Uncalibrated transducer. Please calibrate transducer

P PTRA 000 103

ERROR READING PARAMETERS FROM DIALYSIS PRESSURE TRANSDUCER Unconditional error, blood pump not available General description of conditions for occurring: - An error occurred while reading transducer parameters during init (start-up).

106 (115)



Some possible explanations why the error has occurred: - No connection between transducer board and FM I/O board - No connection between FM I/O board and protective driver board - Transducer board mounted in incorrect position on FM I/O board - Incorrect transducer ID. Please update transducer ID (I2C scan). - Transducer board is broken - Serial bus error on protective U board - Uncalibrated transducer. Please calibrate transducer - Broken FM I/O board P PTRA 000 104

ERROR READING PARAMETERS FROM VENOUS PRESSURE TRANSDUCER Unconditional error, blood pump not available General description of conditions for occurring: - An error occurred while reading transducer parameters during init (start-up). Some possible explanations why the error has occurred: - No connection between transducer board and BM I/O board - No connection between BM I/O board and protective driver board - Transducer board mounted in incorrect position on BM I/O board - Incorrect transducer ID. Please update transducer ID (I2C scan). - Transducer board is broken - Serial bus error on protective U board - Uncalibrated transducer. Please calibrate transducer - Broken BM I/O board

P PTRA 000 105

ERROR READING PARAMETERS FROM PH TRANSDUCER Unconditional error, blood pump not available General description of conditions for occurring: - An error occurred while reading transducer parameters during init (start-up). Some possible explanations why the error has occurred: - No connection between MM I/O board and protective U board - Incorrect transducer ID. Please update transducer ID (I2C scan). - MM I/O board is broken - Serial bus error on protective U board - Uncalibrated transducer. Please calibrate transducer

P PTRA 000 106

ERROR READING PARAMETERS FROM ARTERIAL PRESSURE TRANSDUCER Unconditional error, blood pump not available General description of conditions for occurring: - An error occurred while reading transducer parameters during init (start-up). Some possible explanations why the error has occurred: - No connection between transducer board and BM I/O board - No connection between BM I/O board and protective driver board - Transducer board mounted in incorrect position on BM I/O board - Incorrect transducer ID. Please update transducer ID (I2C scan). - Transducer board is broken - Serial bus error on protective U board - Uncalibrated transducer. Please calibrate transducer - Broken BM I/O board



107 (115)

P PTRA 000 107

ERROR READING PARAMETERS FROM DIASCAN TRANSDUCER Unconditional error, blood pump not available General description of conditions for occurring: - An error occurred while reading transducer parameters during init (start-up). Some possible explanations why the error has occurred: - No connection between transducer board and FM I/O board - No connection between FM I/O board and protective driver board - Transducer board mounted in incorrect position on FM I/O board - Incorrect transducer ID. Please update transducer ID (I2C scan). - Transducer board is broken - Serial bus error on protective U board - Uncalibrated transducer. Please calibrate transducer - Broken FM I/O board

P SDT, U P system P SDT 003 001

CHECK SUM ERROR Unconditional error, blood pump not available General description of conditions for occurring: - The check sum of the protective system presets is not correct. Enter service/ preset and preset the machine (make a default preset). Some possible explanations why the error has occurred: - Broken/ new U P safe-RAM

P SDT 004 001

U C DOES NOT SEND SHUT DOWN ACKNOWLEDGE Some possible explanations why the above error has occurred: - Internal software error

P SDT 004 002

U W DOES NOT SEND SHUT DOWN ACKNOWLEDGE Some possible explanations why the above error has occurred: - Internal software error

P SDT 004 003

SHUT DOWN FAILURE General description of conditions for occurring: - The AK 96 was not switched off within 5 seconds after shut down request. Some possible explanations why the above error has occurred: - Protective driver board broken (IC16 and components)

P SDT 004 004

U C DOES NOT SEND RESET ACKNOWLEDGE Some possible explanations why the above error has occurred: - Internal software error

P SDT 004 005

U W DOES NOT SEND RESET ACKNOWLEDGE Some possible explanations why the above error has occurred: - Internal software error

108 (115)



P SDT 004 006

MAIN RESET FAILURE (U W) Some possible explanations why the above error has occurred: - Internal software error

P SDT 004 007

THE U P CHEM FLAG INCORRECTLY SET Some possible explanations why the above error has occurred: - Internal software error - Corrupt safe-RAM

P SDT 004 008

REQUEST ERROR General description of conditions for occurring: - A single request of signal bmfchpart1, bmfchpart2, fmfchpart1 or fmfchpart2 has been performed. Some possible explanations why the above error has occurred: - Internal software error

P SDT 004 009

REQUEST ERROR Transient error General description of conditions for occurring: - The control system requested a reset to exit maintenance mode. The protective system was not in maintenance mode. Some possible explanations why the above error has occurred: - Internal software error

P SDT 038 001

PRESET ERROR General description of conditions for occurring: - The preset acetate concentrate bank is not set to a valid value. Some possible explanations why the above error has occurred: - Internal software error - Corrupt SAFE -RAM (please make a default preset)

P SDT 038 002

PRESET ERROR General description of conditions for occurring: - The preset bicarbonate concentrate bank is not set to a valid value. - Corrupt SAFE -RAM (please make a default preset)

P SDT 044 001

PROGRAM FLOW ERROR Unconditional error, blood pump not available General description of conditions for occurring: - AK 96 was reset by U P due to a failure in the program flow supervision. Some possible explanations why the above error has occurred: - Internal software error - Broken communication between U P and U or U W - Broken protective U board - Broken control U board - Broken AC/DC unit (check the +5 voltages)



109 (115)

P SDT 046 001

DIASCAN ERROR The total sodium limit has been exceeded in U P. No more Diascan measurements are possible

P SDT 047 001

VENOUS PRESSURE TEST ERROR This error is generated if the conditions for performing the high venous-pressure test are still unfulfilled after 10 minutes into treatment. DIALYSIS PRESSURE TOO HIGH ERROR This error is generated in treatment if the dialysis pressure measured by dialysis pressure sensor is above the value of "Dialysis pressure Sup" preset. DIALYSIS PRESSURE TOO HIGH ERROR This error is generated in priming if the dialysis pressure measured by dialysis pressure sensor is above the value of "Dialysis pressure Sup" preset. DIALYSIS PRESSURE TOO HIGH ERROR This error is generated in rinseback if the dialysis pressure measured by dialysis pressure sensor is above the value of "Dialysis pressure Sup" preset. DIALYSIS PRESSURE TOO HIGH ERROR This silent error is generated in disinfection if the dialysis pressure measured by dialysis pressure sensor is above the value of "Dialysis pressure Sup" preset. DIALYSIS PRESSURE TOO HIGH ERROR This silent error is generated in service and preset mode if the dialysis pressure measured by dialysis pressure sensor is above the value of "Dialysis pressure Sup" preset.

P SDT 048 001

P SDT 048 002

P SDT 048 003

P SDT 048 004

P SDT 048 005

110 (115)



P SYS, System Errors P SYS 000 000

DIVIDE ERROR, DIVISION BY 0, IN U P Transient error Some possible explanations why the error has occurred: - Internal software error

P SYS 000 001

SINGLE STEP TRAP U P Some possible explanations why the error has occurred: - Internal software error - Corrupt memory

P SYS 000 002

NMI (NON MASKABLE INTERRUPT) ERROR IN U P Some possible explanations why the error has occurred: - Internal software error

P SYS 000 003

BREAKPOINT IN U P Some possible explanations why the error has occurred: - Internal software error - Corrupt memory

P SYS 000 004

OVERFLOW IN U P Some possible explanations why the error has occurred: - Internal software error

P SYS 000 005

ARRAY BOUNDS TRAP IN U P Some possible explanations why the error has occurred: - Internal software error

P SYS 000 006

UNUSED OPCODE ERROR IN U P Some possible explanations why the error has occurred: - Internal software error - Corrupt memory

P SYS 000 007

ESCAPE OPCODE ERROR IN U P Some possible explanations why the error has occurred: - Internal software error - Corrupt memory

P SYS 000 008

RESERVED VECTOR IN U P Some possible explanations why the error has occurred: - Internal software error

P SYS 000 040

UNKNOWN INTERRUPT IN U P Some possible explanations why the error has occurred: - Internal software error - Broken protective U board



111 (115)

P SYS 001 000

FLOAT ILLEGAL OPCODE IN U P Transient error Some possible explanations why the error has occurred: - Internal software error

P SYS 001 001

FLOAT REAL OVERFLOW IN U P Some possible explanations why the error has occurred: - Internal software error

P SYS 001 002

FLOAT INTEGER OVERFLOW IN U P Some possible explanations why the error has occurred: - Internal software error

P SYS 001 003

UNDEFINED MESSAGE IN U P Some possible explanations why the error has occurred: - Internal software error

112 (115)



W WAD, U W Check Sum W WAD 000 000

U W, CHECK SUM ERROR Transient error General description of conditions for occurring: - The check sum on U W A/D reference value is corrupted. Calibrate the A/D converter.

W WPR, Program Flow (U W) W WPR 000 xxx

PROGRAM FLOW ERROR General description of conditions for occurring: - A program flow error was detected by U W Some possible explanations why the error has occurred: - Internal software error (see table below)

A) countRecI2C, Signal received in W environment B) countSendI2C, Signal sent from W environment C) countXOutEnv, Signal sent from W SDT D) countXInEnv, Signal received in W SDT Table 1. Explanation of W WPR 000 xxx xxx A) B) C) 000 ---001 ---002 --OK 003 --OK 004 -OK -005 -OK -006 -OK OK 007 -OK OK 008 OK --009 OK --010 OK -OK 011 OK -OK 012 OK OK -013 OK OK -014 OK OK OK 015 OK OK OK


D) -OK -OK -OK -OK -OK -OK -OK -OK


113 (115)

W WSYS, System errors in U W W WSYS 000 401


W WSYS 000 402


W WSYS 000 403


114 (115)



? UDEF xxx xxx, Undefined error ? UDEF xxx xxx

UNDEFINED ERROR General description of conditions for occurring: - Undefined error. Please report to Gambro Technical Service



115 (115)

LOGGING PARAMETERS FOR SERVICE, PROM 3.50

Table of contents:

Array SRI SRL SRP SRR SRB


AK 96®

Program version 3.50 SRI array, Integer variables 0

@BRI( BI_MonitorTemp ),

Scale_Factor_100,

Monitor temperature

1

@PRI( PI_VenPr ),

Scale_Factor_10,

Venous pressure (U P) Scale : 1/10 mmHg Available in service mode only. Use SRP 0,avail. in all modes

2

@PRI( PI_AprLog ),

Scale_Factor_10,

Arterial pressure Scale : 1/10 mmHg

3

@BRI( BI_MeasVol ),

Scale_Factor_10,

Measured heparin volume Scale :1/10ml

4

@BRI( BI_EstAcc ),

Scale_Factor_10,

Estimated acc. heparin. vol. Scale :1/10ml

5

@ORI( OI_HepSet ),

Scale_Factor_10,

Heparin flow set value. Scale : 1/1000 ml/h

6

@BRI( BI_BloodFl ),

Scale_Factor_10,

Blood flow. Scale : 1/10 ml/min

7

@BRI( BI_SNActArtpHTime ),

Scale_Factor_100,

Arterial phase time last cycle. Scale: 0.1 sec

8

@BRI( BI_SNActVenpHTime ),

Scale_Factor_100,

Venous phase time last cycle. Scale: 0.1 sec

9

@FRI( FI_ADRefCoeff ),

Scale_Factor_100,

A/D reference coefficient, U C. Scale: 1mV

10

@FRI( FI_MM90ADRefCoeff ),

Scale_Factor_1,

A/D reference coefficient Scale: 30 uV

11

@FRI( FI_HeaterCycle ),

Scale_Factor_1,

Heater rod duty cycle Scale: 1%

13

@FRI( FI_RegTemp ),

Scale_Factor_100,

Regulatorn temperature. Scale : 1/10 °C

14

@FRI( FI_MM90CondTempA ),

Scale_Factor_100,

Temperature in condcell A. Scale: 1 / 10 °C

15

@FRI( FI_MM90CondTempB ),

Scale_Factor_100,

Temperature in condcell B. Scale: 1 / 10 °C

16

@PRI( PI_CondTempP ),

Scale_Factor_100,

Temperature in condcell P Available in service mode Use SRP 2,avail. in all modes

17

@FRI( FI_HPGPr ),

Scale_Factor_10,

High Pressure Guard pressure Scale: 1mmHg

18

@PRI( PI_BubbleLog),

Scale_Factor_1,

Deairating level 0=high 1=mid 2=low

19

@ORI( OI_CondASet ),

Scale_Factor_100,

CondA set point Scale 1/100 mS/cm

20

@FRI( FI_MM90CondAAvg ),

Scale_Factor_100,

CondA value Scale 1/100 mS/cm

21

@ORI( OI_DoseA ),

Scale_Factor_100,

A concentrate extent of dilution. Scale 1/100

HCEN12371 Rev. 10.2011

AK 96

1

Program version 3.50 Scale_Factor_10,

22

@FRI( FI_RelPumpASpeed ),

Relative pump speed for A-pump. Scale 1/10 %

23

@ORI( OI_CondBSet ),

Scale_Factor_100,

CondB set point Scale 1/100 mS/cm

24

@FRI( FI_MM90CondBAvg ),

Scale_Factor_100,

CondB value Scale 1/100 mS/cm

25

@ORI( OI_DoseB ),

Scale_Factor_100,

B concentrate extent of dilution. Scale 1/100

26

@FRI( FI_RelPumpBSpeed ),

Scale_Factor_10,

Relative pump speed for B-pump. Scale 1/10 %

27

@FRI( FI_RelPumpSpeed ),

Scale_Factor_10,

Relative pump speed in acetate mode Scale 1/10 %

28

@ORI( OI_CondSet ),

Scale_Factor_100,

Conductivity set point acetate Scale 1/100 mS/cm

29

@PRI( PI_AirDetAlarmLog),

Scale_Factor_1,

Air detector status 0=alarm, 1=no alarm, flashing key 2=no alarm

30

@ORI( OI_Dose ),

Scale_Factor_100,

Acetate concentrate extent of dilution Scale 1/100

31

@PRI( PI_PHCompValueLog ),

Scale_Factor_100,

pH value Scale: 1

32

@FRI( FI_FlowPumpCurrent ),

Scale_Factor_1,

Motor current for flowpump. Scale: 1mA

33

@FRI( FI_FlowPumpCycle ),

Scale_Factor_10,

Flow pump duty cycle Scale: 1%

34

@FRI( FI_DegassPr ),

Scale_Factor_10,

Degassing pressure Scale: 1mmHg

35

@FRI( FI_UFVol ),

Scale_Factor_1,

UF volume (accumulated). Scale: 1 ml

36

@FRI( FI_UFRate ),

Scale_Factor_1000,

UF rate. Scale: 1/1000 l/h

37

@FRI( FI_UFRateDisp ),

Scale_Factor_1000,

UF rate. Scale: 1/1000 l/h

38

@FRI( FI_UFCoilCurrent ),

Scale_Factor_10,

Coil current trough UF-cell. Scale: 1mA

HCEN12371 Rev. 10.2011

AK 96

2

Program version 3.50 39

@FRI( FI_TarTimer ),

Scale_Factor_1,

UF Taration timer

40

@FRI( FI_UFCalIsolVol ),

Scale_Factor_10,

Isolated UF, calibration, volume. Scale: 1 ml

41

@FRI( FI_UFCalVolDiff ),

Scale_Factor_100,

UF calibration volume difference from ref. Scale: 1%.

42

@FRI( FI_UFCalIsolVolDiff ),

Scale_Factor_100,

Isolated UF calibration volume difference from ref. Scale: 1%

43

@BRI( BI_VenPr ),

Scale_Factor_10,

Venous Pressure (U C) Scale: 1mmHg

44

@ORI( OI_UFCalRefVol ),

Scale_Factor_10,

UF reference volume, calibration. Scale: 1/10 ml

45

@ORI( OI_NonDiffTime ),

Scale_Factor_1,

Non diffusion time. Scale : 1 min

46

@ORI( OI_edTime ),

Scale_Factor_1,

ed time. Scale : 1 min

47

@FRI( FI_UFCalVol ),

Scale_Factor_10,

UF calibration volume

51

@PRI( PI_DiaPrMeas ),

Scale_Factor_10,

Dialysis pressure Scale: 1mmHg Available in service mode Use SRP 4,avail. in all modes

52

@FRI( FI_CondPAvg ),

Scale_Factor_100,

Average condP value Scale: 1/100 mS/cm

53

@PRI( PI_BlLeakMeasLog ),

Scale_Factor_1,

Blood leak value Scale: 1BLU

54

@FRI( FI_SuumpCurrent ),

Scale_Factor_1,

Suction pump current Scale: 1mmHg

55

@FRI( FI_SuumpCycle ),

Scale_Factor_10,

56

@FRI( FI_PumpSpeedRatio ),

Scale_Factor_10,

Suction pump dutycycle Scale: 1% Pump speed ratio in bicarbonate mode

57

@PRI( PI_AprTstCnt ),

Scale_Factor_1),

Arterial pressure zero test approved, only for logg.

58

@FRI( FI_DiaFlow ),

Scale_Factor_1),

Approx flowrate

59

@FRI( FI_VarFlowMotorPosition ),Scale_Factor_1),

Position of motor for variable flow

60

@PRI( PI_DiascanCondMeas),

Conductivity from Diascan cell

HCEN12371 Rev. 10.2011

Scale_Factor_100);

AK 96

3

Program version 3.50 SRL Array, Boolean variables 0

@PRL( P_PrimDetBlood ),

Scale_Factor_1,

Priming detector (TRUE=blood)

1

@PRL( P_BlPumpCoverOpen ),

Scale_Factor_1,

Blood pump cover open

2

@PRL( P_NoAir ),

Scale_Factor_1,

Air detector.Active in service. Use SRI 29,avail. in all modes

3

@PRL( P_FlowSwitchFlow ),

Scale_Factor_1,

Flow switch (TRUE=flow)

4

@PRL( P_HeaterEnergizedLog),

Scale_Factor_1,

Heater energized (signal PMAINS)

5

@BRL( B_VenClampClosed ),

Scale_Factor_1,

Venous clamp closed

6

@BRL( B_HepPumpOvldAttn ),

Scale_Factor_1,

Heparinpump overload

7

@PRL( P_DiaConByp ),

Scale_Factor_1,

Diaconnectors in by

8

@PRL( P_DiaConDia ),

Scale_Factor_1,

Diaconnectors on dialyzer

9

@PRL( P_SAGSLog ),

Scale_Factor_1,

SAGS status

10

@PRL( P_AprAlarmLog ),

Scale_Factor_1,

Arterial guard activated

11

@BRL( B_ArtClampClosed ),

Scale_Factor_1,

Arterial clamp closed

16

@FRL( F_InPressOk ),

Scale_Factor_1,

INPS activated

17

@FRL( F_InValveOpen ),

Scale_Factor_1,

INVA open

18

@FRL( F_FLVASts ),

Scale_Factor_1,

FLVA in priming mode=TRUE

19

@FRL( F_BicLatchOpen ),

Scale_Factor_1,

BiCart latches open

20

@FRL( F_DRVASts ),

Scale_Factor_1,

DRVA open

21

@FRL( F_RIVASts ),

Scale_Factor_1,

RIVA open

23

@FRL( F_HPGHigh ),

Scale_Factor_1,

HPG activated (>450mmHg)

24

@ORL( O_DIVAOpen),

Scale_Factor_1,

DIVA open

27

@ORL( O_BYVAOpen ),

Scale_Factor_1,

BYVA open

30

@PRL( P_TAVAOpen ),

Scale_Factor_1,

TAVA open

31

@PRL( P_EVVAOpen ),

Scale_Factor_1,

EVVA open

32

@FRL( F_ZEVASts ),

Scale_Factor_1,

ZEVA open

33

@FRL( F_REVASts ),

Scale_Factor_1,

REVA open

34

@FRL( F_AIVASts ),

Scale_Factor_1,

AIVA open

35

@FRL( F_StickAInPos ),

Scale_Factor_1,

Pick-up tube A positioned in MM95

36

@FRL( F_StickBInPos ),

Scale_Factor_1,

Pick-up tube B positioned in MM95

HCEN12371 Rev. 10.2011

AK 96

4

37

@FRL( F_CondAch ),

Program version 3.50 Scale_Factor_1,

Conductivity achieved Status info for uf calib.

38

@FRL( F_TempAch ),

Scale_Factor_1,

Temperature achieved Status info for uf calib.

41

@FRL( F_DegassPrRegOk ),

Scale_Factor_1,

Degassing pressure achieved Status info for uf calib.

50

@PRL( P_FMFchPart1 ),

Scale_Factor_1,

FM1 ready

51

@FRL( F_FlowPumpDecoupl ),

Scale_Factor_1,

Flow pump decoupled

52

@PRL( P_BubbleTrapLow ),

Scale_Factor_1,

Low level in bubble chamber Available in service mode Use SRI 18,avail. in all modes

54

@FRL( F_SuumpDecoupl ),

Scale_Factor_1,

Suc pump has been decoupled

55

@PRL( P_BubbleTrapHigh ),

Scale_Factor_1;

Deairating level alarm high Status info for uf calib. Available in service mode Use SRI 18,avail. in all modes

56

@FRL( F_FIVASts ),

Scale_Factor_1,

57

@PRL( P_DiaCon1Status ),

Scale_Factor_1,

Status signal indicating whether FIVA is activated or not. Status of PEXSG1

58

@PRL( P_DiaCon2Status ),

Scale_Factor_1,

Status of PEXSG2

59

@FRL( F_UPSSts ),

Scale_Factor_1),

Status signal indicating whether UPS is activated or not.

60

@FRL( F_BattSts ),

Scale_Factor_1);

Battery Backup activated or not.

SRP variables, Protective system variables (available in all modes) 0

@cLogPWord,

Scale_Factor_10,

Venous Pressure (U P) Scale: 1mmHg

1

@cLogPWord,

Scale_Factor_10,

TMP Scale: 1mmHg

2

@cLogPWord,

Scale_Factor_100,

Temperature (U P) Scale: 1 degree C

3

@cLogPWord,

Scale_Factor_100,

Conductivity (U P) Scale: 1mS/cm

4

@cLogPWord,

Scale_Factor_10);

Dialysis pressure, pd (U P) Scale: 1mmHg

Scale_Factor_1,

UF-rate. Skale l/h

SRR array, Real variables 0

@FRR( FR_UFRate ),

HCEN12371 Rev. 10.2011

AK 96

5


@FRR( FR_Ch1Rate ),

Scale_Factor_1,

Channel 1 rate. Scale ml/min

2

@FRR( FR_Ch2Rate ),

Scale_Factor_1,

Channel 2 rate. Scale ml/min

3

@FRR( FR_CalCh1ROffset ),

Scale_Factor_1,

Calibration real offset ch1

4

@FRR( FR_CalCh2ROffset ),

Scale_Factor_1,

Calibration real offset ch2

5

@FRR( FR_CalCh1RCoeff ),

Scale_Factor_1,

Calibration real coeff ch1

6

@FRR( FR_CalCh2RCoeff ),

Scale_Factor_1,

Calibration real coeff ch2

7

@FRR( FR_Ch1ROffset ),

Scale_Factor_1,

UF channel 1 offset Channel 1 rate offset calibration factor. Scale: 1 ml / min

8

@FRR( FR_Ch2ROffset ),

Scale_Factor_1,

UF channel 2 offset Channel 2 rate offset calibration factor. Scale: 1 ml / min

9

@FRR( FR_Ch1RCoeff ),

Scale_Factor_1,

UF channel 1 coeff Channel 1 rate coefficient calibration factor.

10

@FRR( FR_Ch2RCoeff ),

Scale_Factor_1,

UF channel 2 coeff Channel 2 rate coefficient calibration factor.

11

@FRR( FR_CalUFRTolerance ),

Scale_Factor_1,

Calibration UF rate tolerance

12

@FRR( FR_CalUFROffset ),

Scale_Factor_1,

Calibration UF rate offset

13

@FRR( FR_UFRTolerance ),

Scale_Factor_1,

UF-rate tolerance.

14

@FRR( FR_UFROffset ),

Scale_Factor_1,

UF-rate offset calibration factor. Scale: 1 ml / min

15

@VFC1.Value,

Scale_Factor_1,

Voltage-to-frequency converter for channel 1 Last measured value for the

HCEN12371 Rev. 10.2011

AK 96

6

Program version 3.50 currently selected parameter. 16

@VFC1.Offset,

Scale_Factor_1,

Voltage-to-frequency converter for channel 1 Offset measured (input=ZOVR) by the converter.

17

@VFC1.Ref,

Scale_Factor_1,

Voltage-to-frequency converter for channel 1 Reference voltage measured by the converter.

18

@VFC1.Mean,

Scale_Factor_1,

Voltage-to-frequency converter for channel 1 The mean value for the latest measurment interval when auto.statistics is enabled.

19

@VFC1.Var,

Scale_Factor_1,

Voltage-to-frequency converter for channel 1 The variance for the latest measurment interval when auto.statistics is enabled.

20

@VFC2.Value,

Scale_Factor_1,

Voltage-to-frequency converter for channel 2 Last measured value for the currently selected parameter.

21

@VFC2.Offset,

Scale_Factor_1,


22

@VFC2.Ref,

Scale_Factor_1,


23

@VFC2.Mean,

Scale_Factor_1,


HCEN12371 Rev. 10.2011

AK 96

7


@VFC2.Var,

Scale_Factor_1,


25

@VFC3.Value,

Scale_Factor_1,

Voltage-to-frequency converter for channel 3 Last measured value for the currently selected parameter.

26

@VFC3.Offset,

Scale_Factor_1,


27

@VFC3.Ref,

Scale_Factor_1,


28

@VFC3.Mean,

Scale_Factor_1,


29

@VFC3.Var,

Scale_Factor_1 );


SRB Array, byte variables 1

( FDTRC$SELECT$PROC ),

Scale_Factor_1

2

( FDTRC$HEATER$ENABLE$CTRL$PROC )

Scale_Factor_1,

3

( FDTRC$SAGS$TEST$PROC ),

Scale_Factor_1,

4

( FDTRC$SAGS$TEST$DRAIN$PROC ),

Scale_Factor_1,

5

( FDTRC$VALVE$TEST$PROC ),

Scale_Factor_1,

6

( FDTRC$DISINFECTION$PROC ),

Scale_Factor_1,

7

( FDTRC$CONC$FILLUP$PROC ),

Scale_Factor_1,

8

( FDTRC$CENTR$FILLUP$PROC ),

Scale_Factor_1,

HCEN12371 Rev. 10.2011

AK 96

8


( FDTRC$DIL$FILLUP$PROC ),

Scale_Factor_1,

10

( FDTRC$CLEAN$CART$PRIM$PROC ),

Scale_Factor_1,

11

( FDTRC$CLEAN$CART$FILL$PROC ),

Scale_Factor_1,

12

( FDTRC$CITRIC$DWELL$PROC ),

Scale_Factor_1,

13

( FDTRC$RINSE$PROC ),

Scale_Factor_1,

14

( FDTRC$HEAT$DIS$TEST$PROC ),

Scale_Factor_1,

15

( FDTRC$HEAT$DIS$FLUSH$PROC ),

Scale_Factor_1,

16

( FDTRC$DRAIN$PROC ),

Scale_Factor_1,

17

( FDTRC$DISINFECTION$TIME$PROC )

Scale_Factor_1,

18

( FDTRC$STICK$A$RESOLVER$PROC ),

Scale_Factor_1,

19

( FDTRC$STICK$B$RESOLVER$PROC ),

Scale_Factor_1,

20

( FDTRC$BIC$LATCH$RESOLVER$PROC)

Scale_Factor_1,

21

( FDTRC$CHEM$FILLUP$RDY$LATCH$PROC ),

Scale_Factor_1,

22

( FDTRC$DISINF$CTRL$PROC ),

Scale_Factor_1,

23

( FDTRC$DRAIN$BEF$CHEM$DIS$PROC

Scale_Factor_1,

24

( FFTRC$FCH$MAIN$PROC ),

Scale_Factor_1,

25

( FFTRC$DISINFECT$VALVES$PROC ),

Scale_Factor_1,

26

( FFTRC$DEGASS$PR$TEST$PROC ),

Scale_Factor_1,

27

( FSTRC$UF$CALIBRATION$PROC ),

Scale_Factor_1,

28

( FSTRC$DRAIN$REF$VOL$PROC ),

Scale_Factor_1,

29

( FSTRC$UF$CALIB$PREP$PROC ),

Scale_Factor_1,

30

( FSTRC$UF$MAIN$FL$OFFSET$PROC )

Scale_Factor_1,

31

( FSTRC$UF$CH1$FLOW$CAL$PROC ),

Scale_Factor_1,

32

( FSTRC$UF$DIFF$CAL$PROC ),

Scale_Factor_1,

33

( FSTRC$$UF$PROC ),

Scale_Factor_1,

34

( FSTRC$UF$ISOL$$PROC ),

Scale_Factor_1,

35

( @FFCNSTATE(FF_VARFLOWMOTOR ),

Scale_Factor_1,

HCEN12371 Rev. 10.2011

AK 96

9

Ak96 Error Code 350 146g6b

Overview 4q3b3c

More details 26j3b

Related Documents 171j1w

Ak96 Error Code 350 146g6b

Code Error 4e4n1v

Schindler 300p Error Code Error Code 2h6nr

Rz Error Code 4l4v15

Error Code Control 116y6b

Code Error Exca Volvo 4m469

More Documents from "Tyo" 1dh60

Kurogaze - Anime Subtitle Indonesia 42r49

Ak96 Error Code 350 146g6b

Bki- Inclining Test 39603d

Applied Geostatistics For Reservoir Characterization 2g361m

Iso 11133:2014 144v41

Sistem Penyaliran Air Tambang 6k6i57