Troubleshooting Bizhub Pro 1050 3vzf

Field Service Ver3.0 Nov.2006

13. JAM CODE

bizhub PRO 1050/1050P 1050e/1050eP

„ TROUBLESHOOTING 13. JAM CODE 13.1 Jam code list Jam

cation

code

Tray 1

J11-01

J11-02

Cause

Resulting

Correction

operation During operation

Classifi-

J11-03

The paper feed sensor /1 (PS7) does

If there is a sheet

Pull out tray /1 and

not turn ON within a specified period of

of paper being

remove jammed paper if

time after the paper feed clutch /1 (CL4)

printed when a

any.

turns ON.

jam occurs, the

The pre-registration sensor /1 (PS17)

main body com-

Open tray /1 and the

does not turn ON within a specified

pletes the paper

main body vertical con-

period of time after the paper feed

exit before stop-

veyance door, and

clutch /1 (CL4) turns ON.

ping operations.

remove jammed paper if any.

The vertical conveyance sensor /1 (PS19) does not turn ON within a specified period of time after the pre-registration sensor /1 (PS17) turns ON. When the trailing edge of paper is - After completion

J11-05

When idling

J11-04

J11-06

ing through the vertical conveyance

of the exit of the

sensor /1 (PS19), the pre-registration

preceding paper,

sensor /1 (PS17) is turned ON by the

the main body

succeeding paper.

stops operations.

The vertical conveyance sensor /1

—

(PS19) turns ON while in idling.

Open the main body vertical conveyance door and remove jammed paper if any.



turns ON while in idling.


J12-01

J12-02

J12-03

During operation

any. Tray 2


If there is a sheet



of paper being


time after the paper feed clutch /2 (CL6)

printed when a

any.

turns ON.

jam occurs, the


main body com-



pletes the paper


period of time after the paper feed-

exit before stop-

veyance door, and

clutch /2 (CL6) turns ON.

ping operations.



any.

(PS21) does not turn ON within a specified period of time after the pre-registration sensor /2 (PS18) turns ON.

2

533


code

Tray 2

J12-04

J12-05

Cause

Resulting

Correction


Jam

cation

When the trailing edge of paper is -

After completion



of the exit of the



preceding paper,

veyance door, and


the main body


succeeding paper.

stops operations.

any.

When idling

Classifi-


—

Open the main body ver-

J12-06


tical conveyance door and remove jammed paper if any.





J13-01

(PF)

J13-02

During operation

any. Tray 3

J13-03


If there is a sheet



of paper being


time after the pick-up clutch /1 (CL6)

printed when a

any.

turns ON.

jam occurs, the


main body com-

Open tray /3, the PF


pletes the paper

front door and the verti-

period of time after the pick-up clutch /

exit before stop-

cal conveyance door /

1 (CL6) turns ON.

ping operations.

Up, and remove jammed paper if any.


J13-04

J13-05

When idling

bizhub PRO 1050/1050P /1050e/1050eP

13. JAM CODE


of the exit of the


preceding paper,


the main body

succeeding paper.

stops operations.


—


Open the PF front door and the vertical conveyance door /Up and remove jammed paper if any.

J13-06





534

2

Jam

cation

code

Tray 4

J14-01

(PF)

J14-02

Cause

Resulting

Correction


Classifi-

13. JAM CODE

J14-03


If there is a sheet



of paper being



printed when a

any.

turns ON.

jam occurs, the


main body com-



pletes the paper

front door and the hori-


exit before stop-

zontal conveyance jam

2 (CL9) turns ON.

ping operations.

release lever and remove jammed paper if any.

When the trailing edge of paper is ing through the loop sensor /2 (PS94), the pre-registration sensor /2 (PS93) is

J15-02

When idling

J15-01

(PF)


If there is a sheet



of paper being



printed when a

any.

turns ON.

jam occurs, the

J15-03

—


Pull out tray /4 and remove jammed paper if any.


main body com-



pletes the paper

front door and the verti-


exit before stop-

cal conveyance door /

3 (CL12) turns ON.

ping operations.

Lw, and remove jammed paper if any.


J15-04

J15-05

When idling

Tray 5


During operation

turned ON by the succeeding paper. J14-04


of the exit of the


preceding paper,


the main body

succeeding paper.

stops operations.


—


Open the PF front door and the vertical conveyance door /Lw and remove jammed paper if any.

J15-06





2

535

bizhub PRO 1050/1050P 1050e/1050eP



Classifi-

Jam

cation

code

Cause

Resulting

Correction

operation If there is a sheet

Open the main body

turn ON within a specified period of

of paper being

front doors /R and /L,

time after the ADU deceleration sensor

printed when a

pull out the ADU section

(PS42) turns ON.

jam occurs, the

and remove jammed

The ADU deceleration sensor (PS42)

main body com-

paper if any.


pletes the paper

each

period of time after the loop sensor

exit before stop-

tray)

(PS16) turns ON.

ping operations.

J17-01

feed conveyance (com-

J17-02

mon to

During operation

The registration sensor (PS40) does not

Paper

The loop sensor (PS16) does not turn

After completion

Open the main body ver-

feed

ON within a specified period of time

of the exit of the

tical conveyance door

convey-

after the vertical conveyance sensor /1

preceding paper,

and remove jammed

ance

(PS19) turns ON.

the main body

paper if any.

Paper

J17-03

stops operations.

(trays 1/ and /2) Paper

J17-04


feed

(PS20) does not turn ON within a speci-

convey-

fied period of time after the vertical con-

ance (tray /2)

veyance sensor /3 (PS21) turns ON. J17-05

The vertical conveyance sensor /1 (PS19) does not turn ON within a specified period of time after the vertical conveyance sensor /2 (PS20) turns ON. The loop sensor (PS16) does not turn

Open the PF front door

feed


and the horizontal con-

convey-

after the PF exit sensor (PS99) turns

veyance jam release

ance (PF)

ON.

lever, and remove

Paper

J17-06

J17-07

feed convey-

J17-08

ance

When idling

jammed paper if any. Paper

J17-09

The paper leading edge sensor (PS41)

—

J17-10


The registration sensor (PS40) turns ON


while in idling.

and remove jammed

The ADU deceleration sensor (PS42)

paper if any.

The loop sensor (PS16) turns ON while in idling.

J17-11

The vertical conveyance sensor /2 (PS20) turns ON while in idling.

J17-12

The multi feed detection boards /1 and

If there is a sheet

/2 detect a double feed.

of paper being printed when a jam occurs, the main body completes the paper exit before stopping operations.

536

Open the main body



During operation

bizhub PRO 1050/1050P /1050e/1050eP

13. JAM CODE

Jam

cation

code J18-01

feed conveyance (PF) J18-02

Resulting

Correction

operation

J18-03

The intermediate sensor /Up (PS91)

If there is a sheet



of paper being

and the PF vertical con-

period of time after the vertical convey-

printed when a

veyance door /Up, and

ance sensor /1 (PS90) turns ON.

jam occurs, the


The loop sensor /1 (PS92) does not

main body com-

any.


pletes the paper

time after the intermediate sensor /Up

exit before stop-

(PS91) turns ON.

ping operations.





time after the pre-registration sensor /2

veyance jam release

(PS93) turns ON.

lever, and remove

The intermediate sensor /Lw (PS97)




period of time after the vertical convey-

veyance door /Lw, and

ance sensor /3 (PS96) turns ON.



any.

jammed paper if any. J18-04

J18-05

turn ON within a specified period of time after the intermediate sensor /Lw (PS97) turns ON. J18-06

The PF exit sensor (PS99) does not turn

Open the PF front door,


the PF vertical convey-

after the loop sensor /1 (PS92) turns

ance door /Up and the

ON.

horizontal conveyance jam release lever, and remove jammed paper if any.

J18-07




and the PF horizontal


conveyance jam release

ON.

lever, and remove


Open the PF front door,


the PF vertical convey-


ance door /Lw and the

ON.

horizontal conveyance

jammed paper if any. J18-08

jam release lever, and remove jammed paper if any. J18-09 J18-10

When idling

Paper

Cause During operation

Classifi-

13. JAM CODE

The intermediate sensor /Up (PS91)

—




The loop sensor /1 (PS92) turns ON

veyance door /Up, and

while in idling.


537

bizhub PRO 1050/1050P 1050e/1050eP


Field Service Ver3.0 Nov.2006 Jam

cation

code

Paper

J18-11

feed conveyance (PF)

Cause

Resulting

Correction

operation When idling

Classifi-


—

while in idling.

Open the PF front door and the horizontal conveyance jam release lever, and remove jammed paper if any.

J18-12 J18-13

The intermediate sensor /Lw (PS97)





veyance door /Lw, and

while in idling.


The PF exit sensor (PS99) turns ON


while in idling.


any. J18-14

veyance jam release lever, and remove J19-01

ance PF

J19-02

During operation

jammed paper if any. Convey-

The main body vertical conveyance

The main body

Close the vertical con-

door is opened while in printing.

stops immedi-

veyance door.

ately. The PF front door is opened while in

The main body/

printing.

PF stops immedi-

Close the PF front door.

ately. While in the print sequence, the maxi-

If there is a sheet

Open the main body

paper

mum density sensor detects paper at

of paper being


exit

the specified timing.

printed when a


jam occurs, the

and remove jammed

main body com-

paper if any.

Fusing/

J21-01

pletes the paper exit before stop-

J31-01

J31-02

J32-01

When idling

ping operations. J21-02

While in idling, the maximum density

During operation

bizhub PRO 1050/1050P /1050e/1050eP

13. JAM CODE

The paper leading edge sensor (PS41)

If there is a sheet


of paper being

period of time after the registration

printed when a

motor (M17) turns no.

jam occurs, the

The fusing exit sensor (PS22) does not

main body com-


pletes the paper

time after the paper leading edge sen-

exit before stop-

sor (PS41) turns ON.

ping operations.

timing.

The paper exit sensor (PS3) does not turn ON within a specified period of time after the fusing exit sensor (PS22) turns ON.

538

—

sensor detects paper at the specified

Jam

cation

code

Fusing/

J32-02

paper exit J32-03

Cause

Resulting

Correction


Classifi-

13. JAM CODE

J32-04

The ADU acceleration sensor (PS49)

If there is a sheet

Open the main body


of paper being


period of time after the fusing exit sen-

printed when a


sor (PS22) turns ON.

jam occurs, the

and remove jammed

The reverse sensor /1 (PS48) does not

main body com-

paper if any.


pletes the paper

time after the ADU acceleration sensor

exit before stop-

(PS49) turns ON.

ping operations.

The PS46 does not turn ON again within a specified period of time after the reverse sensor /1 (PS48) turns ON.

J32-05

The paper exit sensor (PS3) does not turn ON within a specified period of time after the reverse sensor /1 (PS48) turns ON.

J32-06

The paper exit sensor (PS3) does not turn OFF within a specified period of

J32-08

When idling

time after the PS3 turns ON. J32-07

J32-09

The paper exit sensor (PS3) turns ON

—

while in idling. The ADU acceleration sensor (PS49) turns ON while in idling. The fusing exit sensor (PS22) turns ON while in idling.

J32-10

The reverse/exit sensor (PS50) turns ON while in idling.

J32-11

The fusing jam sensor (PS23) turns ON while in idling.

J32-12

The reverse sensor /1 (PS48) turns ON while in idling.

J32-13

The reverse sensor /2 (PS47) turns ON

External

J51-01

During operation

while in idling. The front door/R, /L of the main body

The main body

Open the main body

was opened while printing.

stops immedi-


ately.

pull out the ADU section and remove jammed paper if any.

2

539

bizhub PRO 1050/1050P 1050e/1050eP



Classifi-

Jam

cation

code

DF

J61-1 J61-2 J62-1

Cause

Resulting

The RADF open/close sensor (PS301)

The DF stops

Open the DF open/close

turns OFF while in operation.

immediately. If

cover and remove

The cover open/close switch (MS301)

there is paper

jammed paper if any.

turns OFF while in operation.

being transferred

The original registration sensor /Rt

or having been

(PS306) does not turn OFF within a specified period of time after the prefeed start.

transferred, the main body completes the paper exit before stopping operations.

J62-2

The original conveyance sensor (PS308) does not turn ON within a specified period of time after the prefeed start of the front side of the double sided original (including the single sided original).

J62-3

The original conveyance sensor (PS308) does not turn ON within a specified period of time after the prefeed start of the back side of the double sided original.

J62-4

While in the forward rotation of the original conveyance motor (M301), the original conveyance sensor (PS308) does not turn OFF within a specified period of time after it turns ON.

J62-5

While in the reverse rotation of the original conveyance motor (M301), the original conveyance sensor (PS308) does not turn OFF within a specified period of time after it turns ON.

J62-6

When entering a large size double sided original in the reverse section, the original reverse sensor (PS309) does not turn ON within a specified period of time after the original conveyance sensor (PS308) turns ON.

J62-7

When exiting a large size single sided original, the original exit sensor /Lt (PS307) does not turn ON within a specified period of time after the original conveyance sensor (PS308) turns ON.

540

Correction


bizhub PRO 1050/1050P /1050e/1050eP

13. JAM CODE

Jam

cation

code

DF

J62-8

J62-9

J62-10

Cause

Resulting

Correction


Classifi-

13. JAM CODE

When exiting a large size double sided

The DF stops


original, the original exit sensor /Lt

immediately. If

cover and remove

(PS307) does not turn ON within a

there is paper


specified period of time after the original

being transferred

reverse sensor (PS309) turns ON.

or having been

When exiting a large size single sided

transferred, the

original, the original exit sensor /Lt

main body com-

(PS307) does not turn OFF within a

pletes the paper

specified period of time after it turns

exit before stop-

ON.

ping operations.

When exiting a large size double sided original, the original exit sensor /Lt (PS307) does not turn OFF within a specified period of time after it turns ON.

J63-1

When outputting a large size double sided original from the reverse section, the original reverse sensor (PS309) does not turn ON.

J63-2

When entering a large size double sided original into the reverse section, the original reverse sensor (PS309) does not turn OFF within a specified period of time after it turns ON.

J63-3

When outputting a large size double sided original from the reverse section, the original reverse sensor (PS309) does not turn OFF within a specified period of time after it turns ON.

J63-4

When exiting a small size single sided original, the original exit sensor /Rt (PS314) does not turn OFF within a specified period of time after the original reverse sensor (PS309) turns ON.

J63-5

When exiting a small size double sided original, the original exit sensor /Rt (PS314) does not turn OFF within a specified period of time after the original reverse/exit sensor (PS313) turns ON.

J63-6

When exiting a small size single sided original, the original exit sensor /Rt (PS314) does not turn OFF within a specified period of time after it turns ON.

541

bizhub PRO 1050/1050P 1050e/1050eP



Classifi-

Jam

cation

code

DF

J63-7

J63-8

Cause

The DF stops


original, the original exit sensor /Rt

immediately. If

cover and remove


there is paper


specified period of time after it turns

being transferred

ON.

or having been

When entering a small size double

transferred, the

sided original into the reverse section,

main body com-

the original reverse sensor (PS309)

pletes the paper


exit before stop-

period of time after original conveyance

ping operations.

When outputting a small size double sided original from the reverse section, the original reverse sensor (PS309) does not turn ON within a specified period of time after original conveyance sensor (PS308) turns ON.

J63-10

When entering a small size double sided original into the reverse section, the original reverse sensor (PS309) does not turn OFF within a specified period of time after it turns ON.

J63-11

When outputting a small size double sided original from the reverse section, the original reverse sensor (PS309) does not turn OFF within a specified period of time after it turns ON.

J65-1

The original registration sensor /Rt (PS306) turns ON while in idling.

J65-2

The original conveyance sensor (PS308) turns ON while in idling.

J65-4

The original reverse sensor (PS309) turns ON while in idling.

J65-8

The original exit sensor /Lt (PS307) turns ON while in idling.

J65-10

The original reverse/exit sensor (PS313) turns ON while in idling.

J65-20

The original exit sensor /Rt (PS314) turns ON while in idling.

J65-40

The reverse jam sensor (PS304) turns ON while in idling.

J65-80

The original registration sensor /Lt (PS318) turns ON while in idling.

542

Correction

When exiting a small size double sided

sensor (PS308) turns ON. J63-9

Resulting operation

During operation

bizhub PRO 1050/1050P /1050e/1050eP

13. JAM CODE

Jam

cation

code

FD

J72-01

J72-02

Cause

Resulting

Correction


Classifi-

13. JAM CODE

The FD entrance sensor (PS1) does not

The FD and the

Remove jammed paper if


main body stop

any from the FD/main

time after the main body paper exit sen- immediately.

body.

sor (PS3) turns ON. The intermediate conveyance sensor (PS13) does not turn ON within a specified period of time after the FD entrance sensor (PS1) turns ON.

J72-03

The main tray exit sensor (PS18) does not turn ON within a specified period of time after the intermediate conveyance sensor (PS13) turns ON.

J72-04

The main tray exit sensor (PS18) does not turn OFF within a specified period of time after it turns ON.

J72-05

The sub tray paper exit sensor (PS16) does not turn ON within a specified period of time after the intermediate conveyance sensor (PS13) turns ON.

J72-06

The sub tray paper exit sensor (PS16) does not turn OFF within a specified period of time after it turns ON.

J72-09

The punch conveyance sensor (PS5) does not turn ON within a specified period of time after the FD entrance sensor (PS1) turns ON.

J72-10

The 3rd folding conveyance sensor (PS54) does not turn ON within a specified period of time after the punch conveyance sensor (PS5) turns ON.

J72-11

The punch registration sensor (PS6) does not turn ON within a specified period of time after the punch conveyance sensor (PS5) turns ON.

J72-12

The 1st folding conveyance sensor (PS51) does not turn ON within a specified period of time after the punch registration sensor (PS6) turns ON.

J72-13

The 3rd folding conveyance sensor (PS54) does not turn ON within a specified period of time after the 1st folding conveyance sensor (PS51) turns ON.

J72-14

The intermediate conveyance sensor (PS13) does not turn ON within a specified period of time after the 3rd folding conveyance sensor (PS54) turns ON.

543

bizhub PRO 1050/1050P 1050e/1050eP



Classifi-

Jam

cation

code

FS

J72-16

J72-17

Cause

The FS and the

Remove jammed paper,


main body stop

if any, from the FS/main

time after the main body paper exit sen-

immediately.

body.

sor (PS3) turns ON. The main tray exit sensor (PS10) does time after the stacker entrance sensor (PS5) turns OFF. The stacker entrance sensor (PS5) does not turn ON within a specified period of time after the FNS entrance sensor (PS4) turns ON.

J72-19

While in stapling, the stacker entrance sensor (PS5) does not turn OFF within a specified period of time after the stacker entrance motor (M13) turns ON. While in any other operations than stapling, the PS5 does not turn OFF within a specified period of time after it turns ON.

J72-20

While in stapling a small size paper, the main tray exit sensor (PS10) does not turn ON within a specified period of time after the paper exit arm motor (M23) turns ON.

J72-21

While in stapling a large size paper, the main tray exit sensor (PS10) does not turn OFF within a specified period of time after the paper exit arm motor (M23) turns ON.

J72-22

While in exiting paper in the sub tray, the sub tray paper exit sensor (PS1) does not turn ON within a specified period of time after the FNS entrance sensor (PS4) turns ON.

J72-23

While in exiting paper in the sub tray, the sub tray paper exit sensor (PS1) does not turn OFF within a specified period of time after the PS1 turns ON.

J72-28

While in the straight/shift of the small size paper, the main tray paper exit sensor (PS10) does not turn OFF within a specified period of time after the PS10 turns ON.

544

Correction

The FNS entrance sensor (PS4) does

not turn OFF within a specified period of

J72-18

Resulting operation

During operation

bizhub PRO 1050/1050P /1050e/1050eP

13. JAM CODE

Jam

cation

code

FS

J72-30

J72-39 FD

J72-40

Cause

Resulting

Correction


Classifi-

13. JAM CODE

While in stapling a small size paper, the

The FS and the


main tray paper exit sensor (PS10) does

main body stop

if any, from the FS/main

not turn OFF within a specified period of

immediately.

body. Close the front door.

time after the PS10 turns ON. The door switch (MS1) turns OFF while

The copier stops

in the copy/print.

immediately.

While in the folding operation, the 2nd

The FD and the


folding conveyance sensor (PS53) does

main body stop



immediately.

body.

time after the 1st folding motor (M4) starts to accelerate. J72-41

While in the folding operation, the 3rd folding conveyance sensor (PS54) does not turn ON within a specified period of time after the 1st folding motor (M4) starts to accelerate.

J72-42

While in the folding operation, the 3rd folding conveyance sensor (PS54) does not turn ON within a specified period of time after the 2nd folding motor (M5) starts to accelerate.

J72-43

While in the folding operation, the intermediate conveyance sensor (PS13) does not turn ON within a specified period of time after the 3rd folding motor (M6) starts to accelerate.

J72-44

While in the folding operation, the 3rd folding conveyance sensor (PS54) does not turn ON within a specified period of time after the 2nd folding conveyance sensor (PS53) turns ON.

J72-45

While in the folding operation, the intermediate conveyance sensor (PS13) does not turn ON within a specified period of time after the 3rd folding conveyance sensor (PS54) turns ON.

J72-46

The PI conveyance sensor /Up (PS31) does not turn ON within a specified period of time after the PI pick-up solenoid /Up (SD13) turns ON.

J72-47

The PI exit sensor (PS4) does not turn ON within a specified period of time after the PI conveyance sensor /Up (PS31) turns ON.

545

bizhub PRO 1050/1050P 1050e/1050eP



Classifi-

Jam

cation

code

FD

J72-48

J72-49

Cause

Resulting

Correction


bizhub PRO 1050/1050P /1050e/1050eP

13. JAM CODE

The PI conveyance sensor /Lw (PS37)

The FD and the



main body stop


period of time after the PI pick-up sole-

immediately.

body.

noid /Lw (SD14) turns ON. The PI exit sensor (PS4) does not turn ON within a specified period of time after the PI conveyance sensor /Lw (PS37) turns ON.

J72-50

The FD entrance sensor (PS1) does not turn ON within a specified period of time after the PI exit sensor (PS4) turns ON.

J72-58 SD

The PI multi feed is detected.

J72-59

The door switch (MS1) turns OFF.

J72-61

The entrance sensor (PS1) does not

The SD and the



main body stop

any from the SD/main

time after the exit sensor (PS3) on the

immediately.

body.

main body turns ON. J72-62

The horizontal conveyance sensor /1 (PS2) does not turn ON within a specified period of time after the entrance sensor (PS1) turns ON.

J72-63

The horizontal conveyance sensor /2 (PS3) does not turn ON within a specified period of time after the horizontal conveyance sensor /1 (PS2) turns ON.

J72-64

The horizontal conveyance exit sensor (PS4) does not turn ON within a specified period of time after the horizontal conveyance sensor /2 (PS3) turns ON.

J72-65

The horizontal conveyance exit sensor (PS4) does not turn OFF within a specified period of time after it turns ON.

J72-66

The subtray exit sensor (PS11) does not turn ON within a specified period of time after the horizontal conveyance sensor /1 (PS2) turns ON.

J72-67

The subtray exit sensor (PS11) does not turn OFF within a specified period of time after it turns ON.

J72-68

The entrance sensor (PS1) does not turn ON within a specified period of time after the exit sensor (PS3) on the main body turns ON.

546

2

Jam

cation

code

SD

J72-69

J72-70

Cause

Resulting

Correction


Classifi-

13. JAM CODE

The right angle conveyance sensor /2

The SD and the


(PS6) does not turn ON within a speci-

main body stop


fied period of time after the right angle

immediately.

body.

conveyance motor (M6) turns ON. The folding sensor /1 (PS7) does not turn ON within a specified period of time after the folding entrance motor (M3) turns ON.

J72-71

The saddle stitching paper sensor (PS13) does not turn ON within a specified period of time after the folding sub scan alignment exit motor (M8) turns ON.

J72-72

The bundle sensor /1 (PS14) does not turn ON within a specified period of time after the bundle arm rotation motor (M22) turns ON.

J72-73

The bundle sensor /2 (PS15) does not turn ON within a specified period of time after the bundle clip motor (M11) turns ON.

J72-74

The bundle sensor /4 (PS54) does not turn ON within a specified period of time after the bundle sensor /2 (PS15) turns ON.

J72-75

The entrance sensor (PS1) does not turn Off within a specified period of time after it turns ON.

J72-76

The horizontal conveyance sensor (PS3) does not turn OFF within a specified period of time after the entrance sensor (PS1) turns ON.

J72-77

The right angle conveyance sensor /2 (PS6) does not turn OFF within a specified period of time after the folding entrance motor (M3) turns ON.

J72-78

The folding sensor /2 (PS44) does not turn OFF within a specified period of time after the folding sub scan alignment exit motor (M8) turns ON.

J72-79

The saddle stitching paper sensor (PS13) does not turn OFF within a specified period of time after the folding sub scan alignment exit motor (M8) turns ON.

2

547

bizhub PRO 1050/1050P 1050e/1050eP



cation

code

SD

J72-80

J72-81

Cause

Resulting

Correction


Classifi-

The bundle sensor /1 (PS14) does not turn

The SD and the


OFF within a specified period of time after

main body stop


the bundle clip motor (M11) turns ON.

immediately.

body.

—

Open the FS front door

The bundle sensor /2 (PS15) does not turn OFF within a specified period of time after the bundle registration motor (M12) turns ON.

J72-82

With paper bundle exit, the bundle sensor /4 (PS54) does not turn OFF within a specified period of time after the bundle registration motor (M12) turns ON.

J72-83

The folding age sensor (PS8) does not turn ON within a specified period of time after the folding conveyance motor (M4) turns ON.

J72-84

The tri-folding exit sensor (PS9) does not turn ON within a specified period of time after the folding conveyance motor (M4) turns ON.

J72-85

The folding sub scan alignment exit motor (M8) does not turn OFF within a specified period of time after it turns ON.

J72-86

The folding age sensor (PS8) does not turn OFF within a specified period of time after the folding conveyance motor (M4) turns ON.

J72-87

The tri-folding exit sensor (PS9) does not turn OFF within a specified period of time after it turns ON.

J72-88

With paper bundle exit, the bundle sensor /2 (PS15) does not turn OFF within a specified period of time after it turns ON.

J72-89

The trimmer registration sensor (PS55) does not turn OFF within a specified period of time after the bundle press movement motor (M17) turns ON.

J72-90

The trimmer registration sensor (PS55) does not turn ON within a specified period of time after the bundle registration motor (M12) turns ON.

J72-99

During printing, either the SD front door switch /Rt (MS1) or /Lt (MS2) turns OFF.

FS

J73-01 J73-02

548

2

When idling

bizhub PRO 1050/1050P /1050e/1050eP

13. JAM CODE

The stacker entrance sensor (PS5) turns ON while in idling.

and the jam release lever,

The FNS entrance sensor (PS4) turns

and remove jammed

ON while in idling.

paper, if any.

Jam

cation

code

FS

J73-03

J73-04

Cause

Resulting

Correction


Classifi-

13. JAM CODE

The main tray paper exit sensor (PS10)

—

Open the FS front door

turns ON while in idling. Or, the stack

and the jam release lever,

empty sensor (PS20) turns ON while

and remove jammed

turning ON the power source.

paper, if any.

The sub tray paper exit sensor (PS1) turns ON while in idling.

FD

J73-05

Either of the FD entrance sensor (PS1),

—

Open the FD front door,

the punch conveyance sensor (PS5)

open then the entrance

and the punch registration sensor (PS6)

conveyance jam release


levers /1 and /2 and the punch conveyance jam release levers /1 and /2, and then remove jammed paper, if any.

J73-06

J73-07

Either of the intermediate conveyance

Open the FD front door

sensor (PS13), the sub tray paper exit

and the intermediate

sensor (PS16) and the main tray paper

conveyance jam lever,

exit sensor (PS18) turns ON while in

and remove the jammed

idling.

paper, if any.

Either of the 1st folding conveyance

Open the FD front door,

sensor (PS51), the 2nd folding convey-

pull out the folding con-

ance sensor (PS53), the 3rd folding

veyance section, open

conveyance sensor (PS54), the S size

the folding conveyance

conveyance sensor (PS58), the folding

jam release levers /1 to /

entrance sensor (PS52) and the folding

5, and remove jammed

exit sensor (PS2) turns ON while in

paper, if any.

idling. J73-08

Either of the PI conveyance sensor /Up

Open the FD upper door

(PS31), the PI conveyance sensor /Lw

and remove jammed

(PS37) and the PI exit sensor (PS4)

paper, if any. When


jammed paper gets in the PI exit, open the entrance conveyance jam release lever /1 and remove the jammed paper.

SD

J73-09 J73-10

The entrance sensor (PS1) turns ON

Open the SD front door /

while in idling.

Rt and remove jammed

Either of the horizontal conveyance

paper, if any.

sensor /1 (PS2), the horizontal conveyance sensor /2 (PS3), or the subtray exit sensor (PS11) turns ON while in idling. J73-11

The horizontal conveyance exit sensor



Lt and remove jammed paper, if any.

1

549

bizhub PRO 1050/1050P 1050e/1050eP



Classifi-

Jam

cation

code

SD

J73-12

J73-13

Cause

Resulting

Correction


bizhub PRO 1050/1050P /1050e/1050eP

13. JAM CODE

Either of the right angle conveyance

—


sensor /1 (PS5) or the right angle con-

Rt and remove jammed

veyance sensor /2 (PS6) turns ON while

paper, if any.

in idling. Either of the folding sensor /1 (PS7), the folding age sensor (PS8), the trifolding exit sensor, or the folding sensor /2 (PS44) turns ON while in idling.

J73-14 J73-15

The saddle stitching paper sensor



Lt and remove jammed

Either of the bundle sensor /1 (PS14),

paper, if any.

the bundle sensor /2 (PS15), the bundle sensor /4 (PS54), or the bundle exit sensor /2 (PS57) turns ON while in idling. LS

J73-17

The entrance sensor (PS4) of the tan-

Open the tandem (1st)

dem (1st) LS turns ON while in idling.

LS front door, open then entrance conveyance jam release lever and remove jammed paper, if any.

J73-18

The sub tray exit sensor (PS10) of the


tandem (1st) LS turns ON while in idling.

LS sub tray cover, and remove jammed paper, if any.

J73-19

Either of the conveyance sensors /1, /2


and /3 (PS7, 16 and 17) of the tandem

LS JAM door, and

(1st) LS turns ON while in idling.

remove jammed paper, if

The coupling exit sensor (PS18) of the


tandem (1st) LS turns ON while in idling.

LS front door, open then

any. J73-20

the coupling exit jam release lever, and remove jammed paper, if any. J73-21


Open the tandem (2nd)

dem (2nd) LS turns ON while in idling.

LS front door, open then entrance conveyance jam release lever and remove jammed paper, if any.

J73-22

The sub tray paper exit sensor (PS10)


of the tandem (2nd) LS turns ON while

LS sub tray cover, and

in idling.

remove jammed paper, if any.

550

1

Jam

cation

code

LS

J73-23

Cause

Resulting

Correction


Classifi-

13. JAM CODE

Either of the conveyance sensors /1, /2

—


and /3 (PS7, 16 and 17) of the tandem

LS JAM door, and

(2nd) LS turns ON while in idling.


However, in the case of LS-502, only

any.

the conveyance sensor /1 (PS7) is applicable. J73-24



tandem (2nd) LS turns ON while in

LS front door, open then

idling.

the coupling exit jam

However, in the case of LS-501 only.

release lever and remove jammed paper, if any.

PB

J73-30

The entrance sensor (PS1) turns ON

Open the front door and

while in idling.


The SC entrance sensor (PS2) turns ON

any.

while in idling. The cover paper entrance sensor (PS3) turns ON while in idling. The sub tray exit sensor (PS4) turns ON

Open the upper door

while in idling.

and remove jammed

The SC paper detection sensor (PS16)

Open the front door and



The clamp paper sensor (PS28) turns

any.

paper, if any. J73-31 J73-32

ON while in idling. J73-33

The cover paper switchback sensor (PS44) turns ON while in idling. The cover paper sensor/Rt (PS45) turns ON while in idling. The cover paper sensor/Lt (PS46) turns ON while in idling.

J73-34

The book end sensor (PS61) turns ON

Open the stacker door

while in idling.

and remove jammed

The cover paper conveyance sensor /1

Pull out the paper feed


tray and remove jammed

The cover paper conveyance sensor /2

paper, if any.

paper, if any. J73-35

(PS76) turns ON while in idling. The cover paper conveyance sensor /3 (PS77) turns ON while in idling. The cover paper conveyance sensor /4 (PS78) turns ON while in idling. The cover paper conveyance sensor /5 (PS79) turns ON while in idling.

2

551

bizhub PRO 1050/1050P 1050e/1050eP



cation

code

LS

J74-01

J74-02

Cause

The LS and the


dem (1st) LS does not turn ON within a

main body stop

if any, from the LS/main

specified period of time after the main

immediately.

body.

body paper exit sensor (PS3) turns ON. The entrance sensor (PS4) of the tanspecified period of time after it turns ON.

J74-04

The sub tray exit sensor (PS10) does not turn ON within a specified period of time after the entrance sensor (PS4) of the tandem (1st) LS turns ON. The sub tray exit sensor (PS10) of the tandem (1st) LS does not turn OFF within a specified period of time after it turns ON.

J74-05

The conveyance sensor /1 (PS7) does not turn ON within a specified period of time after the entrance sensor (PS4) of the tandem (1st) LS turns ON.

J74-06

The conveyance sensor /1 (PS7) of the tandem (1st) LS does not turn OFF within a specified period of time after it turns ON.

J74-07

The conveyance sensor /2 (PS16) does not turn ON within a specified period of time after the conveyance sensor /1 (PS7) of the tandem (1st) LS turns ON.

J74-08


J74-09

The conveyance sensor /3 (PS17) does not turn ON within a specified period of time after the conveyance sensor /2 (PS16) of the tandem (1st) LS turns ON.

J74-10


J74-11

The coupling exit sensor (PS18) does not turn ON within a specified period of time after the conveyance sensor /3 (PS17) of the tandem (1st) LS turns ON.

552

Correction


dem (1st) LS does not turn OFF within a J74-03

Resulting operation

During operation

Classifi-

During operation

bizhub PRO 1050/1050P /1050e/1050eP

13. JAM CODE

Jam

cation

code

LS

J74-12

J74-19

Cause

Resulting

Correction


Classifi-

13. JAM CODE


The LS and the


tandem (1st) LS does not turn OFF

main body stop


within a specified period of time after it

immediately.

body.

turns ON. The LS front door open jam. While in any other modes than the tandem mode, the front door switch (MS1) of the tandem (1st) LS turns OFF while in the print/print.

J74-31

The entrance sensor (PS4) of the tandem (2nd) LS does not turn ON within a specified period of time after the coupling exit sensor (PS18) of the tandem (1st) LS turns ON.

J74-32

The entrance sensor (PS4) of the tandem (2nd) LS does not turn OFF within a specified period of time after it turns ON.

J74-33

The sub tray exit sensor (PS10) does not turn ON within a specified period of time after the entrance sensor (PS4) of the tandem (2nd) LS turns ON.

J74-34

The sub tray exit sensor (PS10) of the tandem (2nd) LS does not turn OFF within a specified period of time after it turns ON.

J74-35

The conveyance sensor /1 (PS7) does not turn ON within a specified period of time after the entrance sensor (PS4) of the tandem (2nd) LS turns ON.

J74-36

The conveyance sensor /1 (PS7) of the tandem (2nd) LS does not turn OFF within a specified period of time after it turns ON.

J74-37

The conveyance sensor /2 (PS16) does not turn ON within a specified period of time after the conveyance sensor /1 (PS7) of the tandem (2nd) LS turns ON.

J74-38

The conveyance sensor /2 (PS16) of the tandem (2nd) LS does not turn OFF within a specified period of time after it turns ON.

J74-39

The conveyance sensor /3 (PS17) does not turn ON within a specified period of time after the conveyance sensor /2 (PS16) of the tandem (2nd) LS turns ON.

553

bizhub PRO 1050/1050P 1050e/1050eP



Classifi-

Jam

cation

code

LS

J74-40

J74-41

Cause

Resulting

Correction


bizhub PRO 1050/1050P /1050e/1050eP

13. JAM CODE

The conveyance sensor /3 (PS17) of

The LS and the


the tandem (1st) LS does not turn OFF

main body stop


within a specified period of time after it

immediately.

body.

The entrance sensor (PS1) does not

The PB and the



main body stop

if any, from the PB/main

time after the main body paper exit sen-

immediately.

body.

turns ON. The coupling exit sensor (PS18) does not turn ON within a specified period of time after the conveyance sensor /3 (PS17) of the tandem (2nd) LS turns ON.

J74-42

The coupling exit sensor (PS18) of the tandem (2nd) LS does not turn OFF within a specified period of time after it turns ON.

J74-49

The LS front door open jam. While in any other modes other than the tandem mode, the front door switch (MS1) of the tandem (2nd) LS turns OFF while in the print/print.

PB

J74-60

sor (PS3) turns ON. J74-61

The SC entrance sensor (PS2) does not turn ON within a specified period of time after the entrance sensor (PS1) turns ON.

J74-62

The SC entrance sensor (PS2) does not turn OFF within a specified period of time after it turns ON.

J74-63

The cover paper entrance sensor (PS3) does not turn ON within a specified period of time after the main body paper exit sensor (PS3) turns ON.

J74-64

The sub tray exit sensor (PS4) does not turn ON within a specified period of time after the entrance sensor (PS1) turns ON.

J74-65

The sub tray exit sensor (PS4) does not turn OFF within a specified period of time after it turns ON.

J74-66

The SC paper detection sensor (PS16) does not turn ON within a specified period of time after the SC entrance sensor (PS2) turns ON.

554

2

Jam

cation

code

PB

J74-67

J74-68

Cause

Resulting

Correction


Classifi-

13. JAM CODE

The SC paper detection sensor (PS16)

The PB and the


does not turn OFF within a specified

main body stop


period of time after it turns ON.

immediately.

body.

When conveying two pages at a time, the SC paper detection sensor (PS16) does not turn ON within a specified time period after the SC entrance sensor (PS2) turns ON.

J74-69

When conveying two pages at a time, the SC paper detection sensor (PS16) does not turn OFF within a specified period of time after it turns ON.

J74-70

The SC paper detection sensor (PS16) does not turn OFF within a specified period of time after the SC bundle conveynace motor (M17) turns ON.

J74-71

The clamp paper sensor (PS28) does not turn OFF within a specified period of time after the Clamp motor (M22) turns OFF.

J74-72

The glue apply position detection sensor (PS32) does not turn ON within a specified period of time after reversal of glue tank movement motor (the tank moves back) turns ON.

J74-73

The glue apply position detection sensor (PS32) does not turn OFF within a specified period of time after it turns ON.

J74-74

The cover paper sensor/Rt (PS45) does not turn ON within a specified period of time after the cover paper pick up clutch (MC71) turns ON.

J74-76

When starting trimming of the cover paper fed from the PB, the cover paper switchback sensor (PS44) does not turn ON within a specified time period after the cover paper conveyance motor (M45) turns ON.

J74-77

When trimming of the cover paper fed from the PB is complete, the cover paper switchback sensor (PS44) does not turn OFF within a specified time period after the cover paper conveyance motor (M45) turns ON.

2

555

bizhub PRO 1050/1050P 1050e/1050eP



Classifi-

Jam

cation

code

PB

J74-78

J74-79

Cause

The PB and the


the cover paper fed from the PB, the

main body stop


cover paper sensor/Lt (PS46) does not

immediately.

body.

turn OFF within a specified time period after the cover paper conveyance motor (M45) turns ON. When positioning the leading edge of cover paper sensor/Lt (PS46) does not turn ON within a specified time period after the cover paper conveyance motor (M45) turns ON. When cover paper is fed from the main body, the cover paper sensor/Rt (PS45) does not turn OFF within a specified time period after the cover paper entrance sensor (PS3) turns ON.

J74-82

When starting trimming of the cover paper fed from the main body, the cover paper switchback sensor (PS44) does not turn ON within a specified period of time after the cover paper conveyance motor (M45) turns ON.

J74-83

When trimming of the cover paper fed from the main body is complete, the cover paper switchback sensor (PS44) does not turn OFF within a specified period of time after the cover paper conveyance motor (M45) turns ON.

J74-84

When positioning the leading edge of the cover paper fed from the main body, the cover paper sensor/Lt (PS46) does not turn OFF within a specified time period after the cover paper conveyance motor (M45) turns ON.

J74-85

When positioning the leading edge of the cover paper fed from the main body, the cover paper sensor/Lt (PS46) does not turn ON within a specified time period after the cover paper conveyance motor (M45) turns ON.

J74-86

The book end sensor (PS61) does not turn ON within a specified period of time after the book conveyance belt motor (M61) turns ON.

556

2

Correction

When positioning the leading edge of

the cover paper fed from the PB, the

J74-80

Resulting operation

During operation

bizhub PRO 1050/1050P /1050e/1050eP

13. JAM CODE

Jam

cation

code

PB

J74-87

J74-88

Cause

Resulting

Correction


Classifi-

13. JAM CODE

When loading first book, the book sen-

The PB and the


sor /1 (PS66) does not turn ON within a

main body stop


specified period of time after the book

immediately.

body.

conveyance belt up down motor (M63) turns ON. When first row of book moves, the book sensor /2 (PS67) does not turn ON within a specified period of time after the book movement motor (M64) turns ON.

J74-89

When feeding paper, the cover paper conveyance sensor /1 (PS75) does not turn ON within a specified period of time after the cover paper pick up clutch (MC71) turns ON.

J74-90

The cover paper conveyance sensor /2 (PS76) does not turn ON within a specified period of time after the cover paper conveyance sensor /1 (PS75) turns ON.

J74-91

When re-feeding paper, the cover paper conveyance sensor /3 (PS77) does not turn ON within a specified period of time after the cover paper pick up clutch (MC71) turns ON.

J74-92

The cover paper conveyance sensor /4 (PS78) does not turn ON within a specified period of time after the cover paper conveyance sensor /3 (PS77) turns ON.

J74-93

The multi feed detection board /2 (MFDTB72) turns OFF.

J74-96

The cover paper switchback sensor (PS44) does not turn ON within a specified period of time after the cover paper feed motor (M74) turns ON.

J74-97

No paper is detected (the paper has removed) when restarting the job after recovery.

J74-98

A cover paper has not been conveyed to the cover paper table section when clamping of inside pages is finished.

J74-99

The front door switch (MS2), the upper door switch (MS3) and the stacker door switch (MS4) became OFF during printing.

2

557

bizhub PRO 1050/1050P 1050e/1050eP



cation

code

ADU

J92-01

J92-02

Cause

Resulting

Correction


Classifi-

The ADU reverse sensor /1 (PS46) does

If there is a sheet

Open the main body


of paper being


time after the reverse sensor /1 (PS48)

printed when a


turns ON.

jam occurs, the

and remove jammed

The ADU reverse sensor /1 (PS46) does

main body com-

paper if any.

not turn ON again within a specified

pletes the paper

period of time after the PS46 turns ON.

exit before stop-

J93-01

During operation

J92-04

When idling


The ADU reverse sensor /1 (PS46)

—

turns ON while in idling. The ADU reverse sensor /2 (PS45) turns ON while in idling. The ADU exit sensor (PS43) does not

If there is a sheet

Open the main body


of paper being


time after the ADU reverse sensor /1

printed when a


(PS46) turns ON.

jam occurs, the

and remove jammed

main body com-

paper if any.

pletes the paper exit before stop-

J94-01

During operation

J93-03

When idling


The ADU conveyance sensor /1 (PS35)

—

turns ON while in idling. The ADU conveyance sensor /2 (PS36) turns ON while in idling. The ADU deceleration sensor (PS42)

If there is a sheet


of paper being

period of time after the ADU exit sensor

printed when a

(PS43) turns ON.

jam occurs, the main body completes the paper exit before stopping operations.

J94-03

558

When idling

bizhub PRO 1050/1050P /1050e/1050eP

13. JAM CODE

The ADU exit sensor (PS43) turns ON while in idling.

—

14. MALFUNCTION CODE

bizhub PRO 1050/1050P 1050e/1050eP


14. MALFUNCTION CODE 14.1 Malfunction code list A. Note for use Turn OFF/ON the power switch (SW2) of the main body when releasing an abnormal condition. B. Code list NOTE • For codes with "*" in the code column, "Turn ON the power switch again" is displayed on the touch . For other codes, "Please call service" is displayed. • For codes with "**" in the code column (SC78-40 to 62: perfect binding tank temperature abnormality related), always repair defective parts then set the DipSW3-1 software of service mode to 0. If DipSW3-1 is set to 0 before defective parts are fixed, it may cause fire.

Classification

Code

Causes

Resulting

Estimated abnormal parts

Main body

operation Drive

The main body

Paper feed motor (M4)

paper feed motor (M4) is checked.

stops immediately

Printer control board (PRCB)

An error detection signal is

to turn OFF the

detected twice in succession a

RL1 (main).

SC13-01 An abnormal speed signal of the

specified period of time after M4 was turned ON (the first signal is PF

ignored). SC13-02 An abnormal speed signal of the PFU paper feed motor (M40) is

Paper feed motor (M40) PF drive board (PFUDB)

checked. An error detection signal is detected twice in succession a specified period of time after M40 was turned ON (the first signal is Main body

ignored). SC13-03 The blowout of a fuse for the verti-


cal conveyance motor (M8) in the

Vertical conveyance motor

printer control board (PRCB) is

(M8)

checked. An error detection signal (blowout of a fuse) of M8 is detected when

PF

M8 is turned ON. SC13-05 The blowout of a fuse for the exit

PF exit conveyance motor

conveyance motor (M41) in the PF

(M41)

drive board (PFUDB) is checked.

PF drive board (PFUDB)

An error detection signal (blowout of a fuse) of M41 is detected when M41 is turned ON.

2

559

Classification


Code

Causes

Resulting


operation Main body

bizhub PRO 1050/1050P /1050e/1050eP


The main body

Paper lift motor /1 (M25)

/1 (M25) is detected.

stops immediately

Upper limit sensor /1 (PS6)

An error detection signal of M25 is

to turn OFF the

detected while M25 is ON.

RL1 (main).

Tray /1 SC18-10 The locking of the paper lift motor

Error code is not

DC power supply /2 (DS/

(PS6) is OFF, PS6 does not turn

displayed on the

2)

ON within 20 seconds after the

operation ,

paper lift motor /1 (M25) turns ON

but displayed only

for lifting operation. And at this

on the data collec-

time, an error detection signal

tion, the list output

(24V cut off) is detected.

and CSRC. Since

SC18-11 When the upper limit sensor /1


the lifting opera-


tion of the tray is


not completed,


"Set paper in the


tray 1" is displayed


on the operation

(blowout of a fuse) is detected.

board.



SC18-13 When the upper limit sensor /1 (PS6) is OFF, PS6 does not turn ON within 20 seconds after the paper lift motor /1 (M25) turns ON for lifting operation. And at this time, an error detection signal is not detected. The main body



stops immediately


When M26 is ON, an error detec-

to turn OFF the

tion signal of the M26 is detected.

RL1 (main).


Error code is not



displayed on the

2)


operation ,


but displayed only


on the data collec-




and CSRC. Since



560

the lifting opera-


tion of the tray is


not completed,


"Set paper in the




on the operation


board.


Classification

Code

14. MALFUNCTION CODE Causes

Resulting


Main body

operation Tray /2 SC18-23 When the upper limit sensor /2

Error code is not


displayed on the


operation ,


but displayed only


on the data collec-

time, an error detection signal is


not detected.

and CSRC. Since


the lifting operation of the tray is not completed, "Set paper in the tray 2" is displayed on the operation PF

board. The main body



stops immediately



to turn OFF the


RL1 (main).


Error code is not



displayed on the

2)


operation ,


but displayed only


on the data collec-




and CSRC. Since



the lifting opera-


tion of the tray is


not completed,


"Set paper in the




on the operation


board.



SC18-33 When the upper limit sensor /1 (PS71) is OFF, PS71 does not turn ON within 20 seconds after the paper lift motor /1 (M42) turns ON for lifting operation. And at this time, an error detection signal is not detected. The main body



stops immediately



to turn OFF the


RL1 (main).


561

bizhub PRO 1050/1050P 1050e/1050eP


Classification


Code

Causes

Resulting


operation PF

bizhub PRO 1050/1050P /1050e/1050eP


Error code is not



displayed on the

2)


operation ,


but displayed only


on the data collec-




and CSRC. Since

Tray /4 SC18-41 When the upper limit sensor /2


the lifting opera-


tion of the tray is


not completed,


"Set paper in the




on the operation

(blowout of a fuse) is detected. SC18-43 When the upper limit sensor /2


board. Error code is not


displayed on the


operation ,


but displayed only


on the data collec-



not detected.

and CSRC. Since


the lifting operation of the tray is not completed, "Set paper in the tray 4" is displayed on the operation board. The main body



stops immediately



to turn OFF the


RL1 (main).


Error code is not



displayed on the

2)


operation ,


but displayed only


on the data collec-




and CSRC. Since



562

the lifting opera-


tion of the tray is


not completed,


"Set paper in the




on the operation


board.


Classification


Code

Causes

Resulting


PF

operation Error code is not

Tray /5 SC18-53 When the upper limit sensor /3 (PS83) is OFF, PS83 does not turn

displayed on the


operation ,


but displayed only


on the data collec-



not detected.

and CSRC. Since


the lifting operation of the tray is not completed, "Set paper in the tray 5" is displayed on the operation Main body

board. Wire

SC21-01 It is checked that the time for the

The main body

Charger cleaning motor

cleaning

charger cleaning motor (M23)

stops immediately

(M23)

abnor-

operations is over.

to turn OFF the

Charger cleaning home sen-

mality

• When the charger cleaning RL1 (main). home sensor (PS26) is OFF

sor (PS26) Printer control board (PRCB)

with the main power switch (SW1) ON, PS26 does not turn ON within 35 seconds after the M23 turns ON for home position

research

operation

(return operation). At this time, an

error

detection

signal

(blowout of a fuse) is not detected. • PS26 does not turn OFF within 15 seconds after the reverse operation (return operation) is started. At this time, an error detection signal (blowout of a fuse) is not detected. • The charger cleaning limit sensor (PS27) does not turn ON within a specified period of time after the reverse operation

(return

operation)

is

started for detection of PS26 being OFF. Or, PS26 does not turn ON within a specified period of time after PS27 turns ON. At this time, an error detection signal (blowout of a fuse) is not detected.

563

bizhub PRO 1050/1050P 1050e/1050eP


Classification


Code

Causes

Resulting


operation Main body

bizhub PRO 1050/1050P /1050e/1050eP


The main body


cleaning

charger cleaning motor (M23) in

stops immediately

(M23)

abnor-

the printer control board (PRCB) is

to turn OFF the


mality

checked.

RL1 (main).

Wire

SC21-02 The blowout of a fuse for the

• When the charger cleaning home sensor (PS26) is OFF with the main power switch (SW1) ON, PS26 does not turn ON within 35 seconds after the M23 turns ON for home position

research

operation

(return operation). And at this time, an error detection signal (blowout of a fuse) is detected. • PS26 does not turn OFF within 15 seconds after the reverse operation (return operation) is started. And at this time, an error detection signal (blowout of a fuse) is detected. • The charger cleaning limit sensor (PS27) does not turn ON within a specified period of time after the reverse operation

(return

operation)

is

started for detection of PS26 being OFF. Or, PS26 does not turn ON within a specified period of time after PS27 turns ON. At this time, an error detection signal (blowout of a fuse) is detected. SC21-03 The locking of the charger clean-

(M23)

A motor lock signal is detected

Charger/cleaning member

while moving from the charger cleaning limit sensor (PS27) side to the charger cleaning home sensor (PS26) side, and after a retry operation, a fifth motor lock signal is detected.

564


ing motor (M23) is detected.

Classification


Code

Causes

Resulting


Main body

operation The main body

Transfer/separation clean-

cleaning

the transfer/separation cleaning

stops immediately

ing motor (M20)

abnor-

motor (M20) are over.

to turn OFF the


RL1 (main).

ing home sensor (PS38)

Wire

mality

SC21-04 It is checked that the operations of

• When the transfer/separation cleaning home sensor (PS38)


is OFF with the main power

ing limit sensor (PS39)

switch (SW1) ON, PS38 does

ADU drive boards /1, /2

not turn ON within a specified

(ADUDB/1, /2)

period of time after the transfer/separation cleaning motor (M20) turns ON for a home position

research

operation


error

detection

signal

(blowout of a fuse) is not detected. • PS38 does not turn OFF within a specified period of time after the reverse operation (return operation) is started. At this time, an error detection signal (blowout of a fuse) is not detected. • The transfer/separation cleaning limit sensor (PS39) does not turn ON within a specified period of time after the reverse operation (return operation) is started for detection of PS38 being OFF. Or, PS38 does not turn ON within a specified period of time after PS39 turns ON. At this time, an error detection signal (blowout of a fuse) is not detected.

565

bizhub PRO 1050/1050P 1050e/1050eP


Classification


Code

Causes

Resulting


operation Main body

bizhub PRO 1050/1050P /1050e/1050eP


The main body


cleaning

transfer/separation cleaning motor

stops immediately

ing motor (M20)

abnor-

(M20) in the ADU drive boards /1

to turn OFF the


mality

and /2 (ADUDB/1 and /2)is

RL1 (main).

(ADUDB/1, /2)

Wire


checked. • When the transfer/separation cleaning home sensor (PS38) is OFF with the main power switch (SW1) ON, PS38 does not turn ON within a specified period of time after the transfer/separation cleaning motor (M20) turns ON for a home position

research

operation


error

detection

signal

(blowout of a fuse) is detected. • PS38 does not turn OFF within a specified period of time after the reverse operation (return operation) is started. At this time, an error detection signal (blowout of a fuse) is detected. • PS39 does not turn ON within a specified period of time after the reverse operation (return operation) is started for detection of PS38 being OFF. Or, PS38 does not turn ON within a specified period of time after PS39 turns ON. At this time, an

error

detection

signal

(blowout of a fuse) is detected. SC21-06 The locking of the transfer/separa-

ing motor (M20)

detected.

Transfer/separation charger/

Motor lock signals are detected


while moving from the transfer/

ing member

separation limit sensor (PS39) side to the transfer/separation home sensor (PS38) side, and after a retry operation, a fifth motor lock signal is detected.

566


tion cleaning motor (M20) is

Classification

Code


Resulting


Main body


Transfer assist motor (M19)

cleaning

the transfer assist motor is out.

stops immediately

Transfer assist home sensor

abnor-

The transfer assist home sensor

to turn OFF the

(PS39)

mality


RL1 (main).


Wire

SC21-07 The home position search time of

specified period of time after the

(ADUDB/1, /2)

home position search operation of the transfer assist motor (M19) is started. SC21-08 An error is detected while in the

Transfer assist motor (M19)

operation of the transfer assist


motor.

ing limit sensor (PS39)

An error is detected of the transfer

Transfer assist home sensor

assist motor (M19) while in the

(PS39)

print operation. Motor

SC23-01 The speed error signal of the toner

Toner bottle motor (M6)

abnor-

bottle motor (M6) is checked.


mality

An error detection signal is

Toner bottle/large capacity

detected twice in succession a

hopper

specified period of time after M6 turns ON (the first signal is ignored). SC23-02 The speed error signal of the developing motor (M3) is checked.

Developing motor (M3) Printer control board (PRCB)

Since an error detection signal is detected a second after M3 turns ON, turn OFF M3 for 0.5 seconds. Then, an error detection signal is detected again a second after it is turned ON again. SC23-03 The locking of the blade motor is

Blade motor (M22)

detected.

Blade sensor /1 (PS24), /2

The error detection signal (over

(PS25)

current) of M22 is detected. SC23-04 It is checked that the movement of the blade motor (M22) is not com-

DC power supply /2 (DS/ 2)

pleted, and the 24V power source is also checked. The drum READY1 signal (READY condition) cannot be detected within a specified period of time after the drum motor (M2) turns ON. Or, the drum READY1 signal (READY release condition) cannot be detected within a specified period of time after M2 turns OFF. At this time, an error detection signal (24V cut out) is detected.

567

bizhub PRO 1050/1050P 1050e/1050eP


Classification


Code

Causes

Resulting


operation Main body

bizhub PRO 1050/1050P /1050e/1050eP


The main body

Blade motor (M22)

abnor-

blade motor (M22) in the printer

stops immediately


mality

control board (PRCB) is checked.

to turn OFF the

The drum READY1 signal (READY

RL1 (main).

Motor


condition) cannot be detected within a specified period of time after the drum motor (M2) turns ON. Or, the drum READY1 signal (READY release condition) cannot be detected within a specified period of time after M2 turns OFF. At this time, the error detection signal (blowout of a fuse) of the blade motor (M22) is detected. SC23-06 It is checked that the movement of the blade motor (M22) is not completed. The drum READY1 signal (READY condition) cannot be detected within a specified period of time after the drum motor (M2) turns ON. Or, the drum READY1 signal (READY release condition) cannot be detected within a specified period of time after M2 turns OFF. At this time, an error detection signal is not detected. SC23-07 It is checked that the movement of the blade motor (M22) is not completed, and 24V power source is also checked. The blade READY signal (READY condition) cannot be detected within a specified period of time after the blade replacement signal turns ON. Or, the blade READY signal (READY release condition) cannot be detected within a specified period of time after the blade replacement signal turns OFF. At this time, an error detection signal (24V cut off) is detected.

568


Classification

Code


Resulting


Main body


Blade motor (M22)

abnor-

blade motor (M22) in the printer

stops immediately


mality

control board (PRCB) is checked.

to turn OFF the

The blade READY signal (READY

RL1 (main).

Motor


condition) cannot be detected within a specified period of time after the blade replacement signal turns ON. Or, the blade READY signal (READY release condition) cannot be detected within a specified period of time after the blade replacement signal turns OFF. At this time, an error detection signal (blowout of a fuse) of the blade motor (M22) is detected. SC23-09 It is checked that the movement of the blade motor (M22) is not completed. The blade READY signal (READY condition) cannot be detected within a specified period of time after the blade replacement signal turns ON. Or, the blade READY signal (READY release condition) cannot be detected within a specified period of time after the blade replacement signal turns OFF. At this time, an error detection signal is not detected. SC23-10 It is checked that the drum motor (M2) does not start. The drum

Drum motor (M2) Printer control board (PRCB)

READY2 signal (READY signal) is not detected within a specified period of time after M2 turns ON. SC23-11 The blowout of a fuse for the inter-

Intermediate hopper motor

mediate hopper motor (M11) in

(M11)



checked. An error detection signal (blowout of a fuse) is detected when M11 turns ON.

569

bizhub PRO 1050/1050P 1050e/1050eP


Classification


Code

Causes

Resulting


operation Main body

bizhub PRO 1050/1050P /1050e/1050eP


The main body

Air separation motor (M10)

abnor-

separation motor (M10) in the

stops immediately


mality


to turn OFF the

checked.

RL1 (main).

Motor

SC23-12 The blowout of a fuse for the air

An error detection signal (blowout of a fuse) is detected when M10 turns ON. Toner

SC23-13 Air separation motor (M10) rota-

Air separation motor (M10)

convey-

tion abnormality. Since an error is

Air motor encoder sensor

ance

detected when M10 turns ON,

(PS30)

abnor-

turn it OFF. An error is still

Resetting of the intermedi-

mality

detected when turn it ON again. SC23-14 The toner conveyance abnormality

ate toner hopper section Toner pump motor (M28)

is detected. When toner is sup-

Air pump motor (M29)

plied for 8 minutes and the toner

Toner remaining sensor /1

remaining sensor /1 (PS31) does

(PS31)

not turn ON, it is found that the


toner remaining sensor /3 (PS33)

(PS33)

of the large capacity hopper turns ON for the last 15 seconds in succession.

Note: • When the code SC2314 occurs, be sure to repair defective parts before

setting

the

software DIPSW3-1 to 0.

Setting

the

DIPSW3-1 to 0 without repairing defective parts may cause toner

to

overflow

inside and outside of the machine. SC23-15 Toner remaining detection sensor / 3 (PS33) abnormality. When the

(PS32)



does not turn ON even if toner is

(PS33)

supplied for 8 minutes, it is found that the toner remaining sensor /2 (PS32) of the large capacity hopper turns ON for the last 15 seconds in succession, and the toner remaining sensor /3 (PS33) turns OFF.

570


Classification


Code

Causes

Resulting


Main body


Toner pump motor (M28)

convey-

detected. When the toner pump

stops immediately


ance

motor (M28) is operating, the

to turn OFF the


abnor-


RL1 (main).

(PS34)

mality

detects the toner being provided

Toner

SC23-17 Leakage at the mixing section is

in succession for 20 seconds.

Note: • When the code SC2317 occurs, be sure to repair defective parts before

setting

the

software DIPSW3-1 to 0.

Setting

the

DIPSW3-1 to 0 without repairing defective parts may cause toner

to

overflow

inside and outside of the machine. SC23-20 Toner pump motor (M28) abnor-


mality. The rotation of the toner

2)

pump motor (M28) and the 24 V


power source are checked. While M28 is rotating, an error detection signal (abnormal rotation) is detected for more than 1 second. At this time, an error detection signal (24V cut off) is detected. SC23-21

• Toner

pump

motor

(M28)


abnormality. The blowout of a


fuse for the toner pump motor

Recycle cut motor (M30)

(M28) in the printer control board (PRCB) is checked. While M28 is rotating, an error detection

signal

(abnormal

rotation) is detected for more than 1 second. At this time, an error detection signal (blowout of a fuse) is detected, but an error signal (24V cut off) is not detected. • When recycle cut motor (M30) is

operating,

abnormality

detection signal was continuously detected twice for the specified

time.

(First

time

ignored)

2

571

bizhub PRO 1050/1050P 1050e/1050eP


Classification


Code

Causes

Resulting


operation Main body

bizhub PRO 1050/1050P /1050e/1050eP


The main body


convey-

mality. The rotation of the toner

stops immediately

Pump encoder sensor /1

ance

pump motor (M28) is checked.

to turn OFF the

(PS28)

abnor-

While M28 is rotating, an error

RL1 (main).

mality

detection signal (abnormal rota-

Toner

SC23-22 Toner pump motor (M28) abnor-

tion) is detected for more than 1 second. At this time, error signals (blowout of a fuse and 24V cut off) are not detected. SC23-24 Air pump motor (M29) abnormal-


ity. The rotation of the air pump

2)

motor (M29) and the 24V power


source are checked. While M29 is rotating, an error detection signal (abnormal rotation) is detected for more than 1 second. At this time, an error signal (24V cut off) is detected. SC23-25 Air pump motor (M29) abnormality. The blowout of a fuse for the

Printer control board (PRCB) Air pump motor (M29)

air pump motor (M29) in the printer control board (PRCB) is checked. While M29 is rotating, an error detection signal (abnormal rotation) is detected for more than 1 second. At this time, an abnormality signal (blowout of a fuse) is detected, but no abnormality signal (24V cut off) is detected. SC23-26 Air pump motor (M29) abnormal-

Pump encoder sensor

motor (M29) is checked for more

(PS29)

than 1 second. An error detection

Load of the pump

signal (abnormal rotation) is detected for more than 1 second. At this time, error signals (blowout of a fuse and 24V cut off) are not detected.

572


ity. The rotation of the air pump

Classification

Code


Resulting


Main body

operation Toner

SC-23-50 Toner collection box detected full

When the waste

convey-

toner amount

ance

exceeds 80% of

abnor-

the toner collec-

mality

tion box, a warn-

Toner collection box

ing message is displayed in the operation and the recycle cut motor (M30) is stopped after specific printing. Drum

The main body

Drum temperature sensor

of the drum temperature sensor

stops immediately

(TH5)

(TH5) is less than -2°C a specified

to turn OFF the

period of time after the main

RL1 (main).

SC24-01 When the change in temperature

power switch (SW1) turns ON to start the control of the dehumidification heater /1 (HTR1) and the drum temperature is below 10°C after the elapse of 1 minute. SC24-02 When the main power switch (SW1) turns ON with the fusing temperature below 50°C, the detected temperature of the drum temperature sensor (TH5) is more than 52°C, and when the detected temperature is above 52°C after a specified period of time. High

SC28-01 A charge leak is detected. After a

Charger

voltage

charge error detection signal is

Power feeding

power

detected while in the charge ON,

High voltage unit /1 (HV1)

source

up to 5 charge ON/OFF opera-

abnor-

tions occur in succession while in

mality

10 prints. SC28-02 A transfer leak is detected. After a

Transfer/separation charger

transfer error detection signal is

Power feeding point

detected while in the transfer ON,


up to 5 transfer ON/OFF operations occur in succession while in 10 prints. SC28-03 A separation leak is detected. After a separation error detection signal is detected while in the separation ON, up to 5 separation ON/OFF operations occur in succession while in 10 prints.

2

573

bizhub PRO 1050/1050P 1050e/1050eP


Classification


Code

Causes

Resulting


operation Main body

bizhub PRO 1050/1050P /1050e/1050eP


The main body


voltage

of a 24V fuse) of the high voltage

stops immediately

(ADUDB1, 2)

power

unit /2 (HV2) is detected.

to turn OFF the


High

SC28-04 The error detection signal (blowout

source

RL1 (main).

abnormality Process

Toner control sensor board

SC29-01 The dirt correction of the sensor is

abnor-

not completed. While in the maxi-

mality

mum density correction, the dirt

(TCSB)

correction of the maximum density sensor is not sufficient. When this condition is detected 10 times in succession, the error code is displayed. Error code is not


is not completed. While in the

displayed on the

(TCSB)

maximum density correction, the

operation ,

Developing motor (M3)

number of rotations of the devel-

but displayed only

oping sleeve gets to the maxi-

on the data collec-

mum.


SC29-02 The maximum density correction

and the CSRC.


put abnormality. While in the maxi-

The control of the

(TCSB)

mum density correction, a patch

main body is

Write unit

for control is not output. (No out-

made by using a

Image processing board

put is made from the maximum

data previously

(IPB)

density sensor.)

obtained.

Overall control board

SC29-03 The maximum density sensor out-

(OACB) The main body


not completed. While in gamma

stops immediately

(TCSB) (gamma sensor

correction, the dirt correction of

to turn OFF the

cleaning required)

the gamma sensor is not suffi-

RL1 (main).


cient. When gamma sensor less than the specified value is detected ten times in succession, this error code is displayed.

574

2

Classification

Code


Resulting


Main body

operation SC29-05 The gamma sensor output abnor-

Error code is not


abnor-

mality. While in the gamma correc-

displayed on the

(TCSB)

mality

tion, a patch for control is not

operation ,

Write unit

output. (No output is made from

but displayed only


the gamma sensor.)

on the data collec-

(IPB)



and the CSRC.

(OACB)

The control of the


defective. The gamma correction

main body is

(IPB)

output is abnormal. A regression

made by using a


error when carrying out a gamma

data previously

curve operation while in the

obtained.

Process

SC29-06 The gamma correction data is

gamma correction. The main body


not completed. While in the dot

stops immediately

(TCSB) (gamma sensor

diameter correction, the dirt cor-

to turn OFF the

cleaning required)

rection of the gamma sensor is

RL1 (main).


not sufficient. When gamma sensor less than the specified value is detected five times in succession, this error code is displayed. SC29-08 Correction abnormality. While in

Error code is not


the dot diameter correction, the

displayed on the

(IPB)

correction is terminated with an

operation ,


abnormal value.

but displayed only on the data collection, the list output and the CSRC. The control of the main body is made by using a data previously obtained. The main body

Drum potential sensor (DPS)

put abnormality. While in the 0V

stops immediately


check of the DPS, more than

to turn OFF the

100V of the drum surface potential

RL1 (main).

SC29-09 Drum potential sensor (DPS) out-

is detected more than 5 times. When the error code is detected 5 times in succession, this error code is displayed.

2

575

bizhub PRO 1050/1050P 1050e/1050eP


Classification


Code

Causes

Resulting


operation Main body

bizhub PRO 1050/1050P /1050e/1050eP


The main body


abnor-

put abnormality. While in the drum

stops immediately


mality

potential correction, a patch for

to turn OFF the

control is not output with the V1

RL1 (main).

Process

SC29-10 Drum potential sensor (DPS) out-

getting to more than 350V. When this condition is detected 5 times in succession, the error code is displayed. SC29-11 The data is defective. While in the drum potential correction, no convergence is obtained even after correction is made more than 10 times. When this condition is detected 5 times in succession, the error code is displayed. SC29-12 Auto adjustment monitor value

Error code is not

abnormality. No convergence is

displayed on the

made in the auto adjustment of

operation ,

the transfer current.

but displayed only

SC29-13 Auto adjustment monitor value

on the data collec-

abnormality. No convergence is


made in the auto adjustment of

and the CSRC.

the separation (AC) current.

The control of the

SC29-14 Auto adjustment monitor value abnormality. No convergence is made in the auto adjustment of the separation (DC) current.


main body is made by using a data previously obtained. High voltage unit /1 (HV1)

SC29-15 Auto adjustment monitor value abnormality. No convergence is made in the auto adjustment of the developing bias. The main body

Drum

tion abnormality. When the

stops immediately


charger grid/developing bias is in

to turn OFF the

excess of the limit of correction,

RL1 (main).

SC29-16 Drum charger capacity deteriora-

lower the developing potential/ fogging margin potential in steps of 50V. And as a result, less than 50V of the difference with the target charger potential is detected 10 times in succession.

576

Classification

Code


Resulting


Main body



abnor-

(FM12) is checked, and the 24V

stops immediately

1)

mality

power source is also checked. An

to turn OFF the

abnormal signal condition occurs

RL1 (main).

Fan

SC32-01 The rotation of the IPB cooling fan

a specified period of time after FM12 is turned ON. This abnormal condition recurs even a specified period of time after FM12 is turned OFF and then turned ON, and an error detection signal (24V cut off) is detected. AC drive board (ACDB)

SC32-02 The blowout of a fuse for the IPB

IPB cooling fan (FM12)

cooling fan (FM12) in the AC drive board (ACDB) is checked. An abnormal condition occurs with the FM12 EM signal a specified period of time after FM12 is turned ON. This abnormal condition recurs even a specified period of time after FM12 is turned OFF and then turned ON, and an error detection signal (blowout of a fuse) is detected with the 24V normal. SC32-03 The rotation of the IPB cooling fan (FM12) is checked. An abnormal condition occurs with the FM12 EM signal a specified period of time after FM12 is turned ON. This abnormal condition recurs even a specified period of time after FM12 is turned OFF and then turned ON, and an error detection signal (24V cut off/blowout of a fuse) is not detected. Error code is not

AC drive board (ACDB)

signal of the PB cooling fan

displayed on the

IPB cooling fan (FM12)

(FM12) turns ON.

operation ,

SC32-04 When the print is started, the EM

but displayed only on the data collection, the list output and the CSRC. The control of the main body is made by using a data previously obtained.

577

bizhub PRO 1050/1050P 1050e/1050eP


Classification


Code

Causes

Resulting


operation Main body

bizhub PRO 1050/1050P /1050e/1050eP


The main body


abnor-

fan (FM11) is checked, and the

stops immediately

2)

mality

24V power source is also

to turn OFF the

checked.

RL1 (main).

Fan

SC32-05 The rotation of the pump cooling

An abnormal condition occurs with the FM11 EM signal a specified period of time after FM11 is turned ON. This abnormal condition recurs even a specified period of time after FM11 is turned OFF and then turned ON, and an error detection signal (24V cut off) is detected. SC32-06 The blowout of a fuse for the pump cooling fan (FM11) in the

Pump cooling fan (FM11) Printer control board (PRCB)

printer control board (PRCB) is checked. An abnormal condition occurs with the FM11 EM signal a specified period of time after FM11 is turned ON. This abnormal condition recurs even a specified period of time after FM11 is turned OFF and then turned ON, and an error detection signal (blowout of a fuse) is detected. SC32-07 The rotation of the pump cooling fan (FM11) is checked. An abnormal condition occurs with the FM11 EM signal a specified period of time after FM11 is turned ON. This abnormal condition recurs even a specified period of time after FM11 is turned OFF and then turned ON, and an error detection signal (24V cut off/blowout of a fuse) is not detected.

578

Pump cooling fan (FM11) Printer control board (PRCB)

Classification

Code


Resulting


Main body



abnor-

ration suction fan (FM4) is

stops immediately

1)

mality

checked, and the 24V power

to turn OFF the

source is also checked.

RL1 (main).

Fan

SC32-09 The rotation of the transfer/sepa-

An abnormal condition occurs with the FM4 EM signal a specified period of time after FM4 is turned ON. This abnormal condition recurs even a specified period of time after FM4 is turned OFF and then turned ON, and an error detection signal (24V cut off) is detected. SC32-10 The blowout of a fuse for the

Transfer/separation suction

transfer/separation suction fan

fan (FM4)

(FM4) in the printer control board


(PRCB) is checked. An abnormal condition occurs with the FM4 EM signal a specified period of time after FM4 is turned ON. This abnormal condition recurs even a specified period of time after FM4 is turned OFF and then turned ON, and an error detection signal (blowout of a fuse) is detected with the 24V normal. SC32-11 The rotation of the transfer/sepa-

Transfer/separation suction

ration suction fan (FM4) is

fan (FM4)

checked.


An abnormal condition occurs with the FM4 EM signal a specified period of time after FM4 is turned ON. This abnormal condition recurs even a specified period of time after FM4 is turned OFF and then turned ON, and an error detection signal (24V cut off/blowout of a fuse) is not detected.

579

bizhub PRO 1050/1050P 1050e/1050eP


Classification


Code

Causes

Resulting


operation Main body

bizhub PRO 1050/1050P /1050e/1050eP


The main body


abnor-

suction fan (FM5) is checked, and

stops immediately

1)

mality

the 24V power source is also

to turn OFF the

checked.

RL1 (main).

Fan

SC32-12 The rotation of the developing


Developing suction fan

developing suction fan (FM5) in

(FM5)



checked. An abnormal condition occurs with the FM5 EM signal a specified period of time after FM5 is turned ON. This abnormal condition recurs even a specified period of time after FM5 is turned OFF and then turned ON, and an error detection signal (blowout of a fuse) is detected with the 24V normal. SC32-14 The rotation of the developing

(FM5)

An abnormal condition occurs


with the FM5 EM signal a specified period of time after FM5 is turned ON. This abnormal condition recurs even a specified period of time after FM5 is turned OFF and then turned ON, and an error detection signal (24V cut off/blowout of a fuse) is not detected.

580

Developing suction fan

suction fan (FM5) is checked.

Classification

Code


Resulting


Main body

operation Fan

SC32-15 The rotation of the paper exit cool- The main body

abnor-

ing fan /1 (FM9) is checked, and

stops immediately

mality


to turn OFF the

checked.

RL1 (main).



Paper exit cooling fan /1

paper exit cooling fan /1 (FM9) in

(FM9)



checked. An abnormal condition occurs with the FM9 EM signal a specified period of time after FM9 is turned ON. This abnormal condition recurs even a specified period of time after FM9 is turned OFF and then turned ON, and an error detection signal (blowout of a fuse) is detected with the 24V normal. SC32-17 The rotation of the paper exit cool-

Paper exit cooling fan /1

ing fan /1 (FM9) is checked.

(FM9)




581

bizhub PRO 1050/1050P 1050e/1050eP


Classification


Code

Causes

Resulting


operation Main body

bizhub PRO 1050/1050P /1050e/1050eP


The main body


abnor-

ing fan /2 (FM10) is checked, and

stops immediately

1)

mality


to turn OFF the

checked.

RL1 (main).

Fan

SC32-18 The rotation of the paper exit cool-

An abnormal condition occurs with the FM10 EM signal a specified period of time after FM10 is turned ON. This abnormal condition recurs even a specified period of time after FM10 is turned OFF and then turned ON, and an error detection signal (24V cut off) is detected. SC32-19 The blowout of a fuse for the paper exit cooling fans /2 (FM10)

Paper exit cooling fans /2 (FM10), /3 (FM28)

and /3 (FM28) in the printer control board (PRCB) is checked. An abnormal condition occurs with the FM10 EM signal a specified period of time after FM10 is turned ON. This abnormal condition recurs even a specified period of time after FM10 is turned OFF and then turned ON, and an error detection signal (blowout of a fuse) is detected with the 24V normal. SC32-20 The rotation of the paper exit cooling fans /2 (FM10) and /3 (FM28) is checked. An abnormal condition occurs with the FM10 EM signal a specified period of time after FM10 is turned ON. This abnormal condition recurs even a specified period of time after FM10 is turned OFF and then turned ON, and an error detection signal (24V cut off/blowout of a fuse) is not detected.

582

Paper exit cooling fans /2 (FM10), /3 (FM28)

Classification

Code


Resulting


Main body



abnor-

assist fan /Fr1 (FM20) is checked,

stops immediately

1)

mality

and the 24V power source is also

to turn OFF the

checked.

RL1 (main).

Fan

SC32-21 The rotation of the paper feed


Paper feed assist fan /Fr1

paper feed assist fan /Fr1 (FM20)

(FM20)

in the printer control board (PRCB)


is checked. An abnormal condition occurs with the FM20 EM signal a specified period of time after FM20 is turned ON. This abnormal condition recurs even a specified period of time after FM20 is turned OFF and then turned ON, and an error detection signal (blowout of a fuse) is detected with the 24V normal. SC32-23 The rotation of the paper feed


assist fan /Fr1 (FM20) is checked.

(FM20)




583

bizhub PRO 1050/1050P 1050e/1050eP


Classification


Code

Causes

Resulting


operation Main body

bizhub PRO 1050/1050P /1050e/1050eP


The main body


abnor-

assist fan /Rr1 (FM21) is checked,

stops immediately

1)

mality


to turn OFF the

checked.

RL1 (main).

Fan



Paper feed assist fan /Rr1

paper feed assist fan /Rr1 (FM21)

(FM21)




(FM21)




584


assist fan /Rr1 (FM21) is checked.

Classification

Code


Resulting


Main body



abnor-


stops immediately

1)

mality


to turn OFF the

checked.

RL1 (main).

Fan





(FM22)



is checked. An abnormal condition occurs with the FM22 EM signal a specified period of time after FM22 is turned ON. This abnormal condition recurs even a specified period of time after FM22 is turned OFF and then turned ON, and an error detection signal (blowout of a fuse) is detected. SC32-29 The rotation of the paper feed



(FM22)




585

bizhub PRO 1050/1050P 1050e/1050eP


Classification


Code

Causes

Resulting


operation Main body

bizhub PRO 1050/1050P /1050e/1050eP


The main body


abnor-


stops immediately

1)

mality


to turn OFF the

checked.

RL1 (main).

Fan





(FM23)




(FM23)




586



Classification

Code


Resulting


PF



abnor-


stops immediately

2)

mality


to turn OFF the

checked.

RL1 (main).

Fan





(FM41)






(FM41)




587

bizhub PRO 1050/1050P 1050e/1050eP


Classification


Code

Causes

Resulting


operation PF

bizhub PRO 1050/1050P /1050e/1050eP


The main body


abnor-


stops immediately

2)

mality


to turn OFF the

checked.

RL1 (main).

Fan





(FM42)




(FM42)




588



Classification

Code


Resulting


PF



abnor-


stops immediately

2)

mality


to turn OFF the

checked.

RL1 (main).

Fan





(FM43)






(FM43)




589

bizhub PRO 1050/1050P 1050e/1050eP


Classification


Code

Causes

Resulting


operation PF

bizhub PRO 1050/1050P /1050e/1050eP


The main body


abnor-


stops immediately

2)

mality


to turn OFF the

checked.

RL1 (main).

Fan





(FM44)




(FM44)




590



Classification

Code


Resulting


PF



abnor-


stops immediately

2)

mality


to turn OFF the

checked.

RL1 (main).

Fan





(FM45)






(FM45)



with the FM45 EM signal a specified period of time after FM45 is turned ON. This abnormal condition recurs even a specified period of time after FM45 is turned OFF and then turned ON, and no error detection signal (24V cut off/blowout of a fuse) is detected.

591

bizhub PRO 1050/1050P 1050e/1050eP


Classification


Code

Causes

Resulting


operation PF

bizhub PRO 1050/1050P /1050e/1050eP


The main body


abnor-


stops immediately

2)

mality


to turn OFF the

checked.

RL1 (main).

Fan





(FM46)




(FM46)




592



Classification

Code


Resulting


PF



abnor-

(FM20) is checked, and the 24V

stops immediately

2)

mality

power source is also checked.

to turn OFF the


RL1 (main).

Fan

SC32-51 The rotation of the cooling fan

with the FM46 EM signal a specified period of time after FM46 is turned ON. This abnormal condition recurs even a specified period of time after FM46 is turned OFF and then turned ON, and an error detection signal (24V cut off) is detected. SC32-52 The blowout of a fuse for the cooling fan (FM20) in the printer con-

Cooling fan (FM20) PF drive board (PFUDB)

trol board (PRCB) is checked. An abnormal condition occurs with the FM46 EM signal a specified period of time after FM46 is turned ON. This abnormal condition recurs even a specified period of time after FM46 is turned OFF and then turned ON, and an error detection signal (blowout of a fuse) is detected with the 24V norMain body

mal. SC32-53 The rotation of the cooling fan (FM20) is checked. An abnormal condition occurs with the FM46 EM signal a specified period of time after FM46 is turned ON. This abnormal condition recurs even a specified period of time after FM46 is turned OFF and then turned ON, and an error detection signal (24V cut off/blowout of a fuse) is not detected.

593

bizhub PRO 1050/1050P 1050e/1050eP


Classification


Code

Causes

Resulting


operation Main body

bizhub PRO 1050/1050P /1050e/1050eP


The main body


abnor-

cooling fan /3 (FM27) is checked.

stops immediately

2)

mality


to turn OFF the

with the FM27 EM signal a speci-

RL1 (main).

Fan

SC32-54 The rotation of the power supply

fied period of time after FM27 is turned ON. This abnormal condition recurs even a specified period of time after FM27 is turned OFF and then turned ON, and no error detection signal (24V cut off/blowout of a fuse) is detected. SC32-55 The EM signal of the power supply

Error code is not

cooling fan /3 (FM27) is ON when

displayed on the

starting the print.

operation , but displayed only on the data collection, the list output and the CSRC. The control of the main body is made by using a data previously obtained. The main body

ADU drive board /2

sec-

motor of the registration section in

stops immediately

(ADUDB2)

tion

the ADU drive board /2 (ADUDB2)

to turn OFF the

ADU conveyance motor /2

motor

is checked.

RL1 (main).

(M16)

abnor-

An error detection signal (blowout

Registration motor (M17)

mality

of a fuse) of the ADU conveyance

Loop motor (M18)

ADU


motor /2 (M16)/ registration motor (M17)/loop motor (M18) is detected after the print is started. At this time, the closing of the door detection/PFU door is detected 10 times in succession.

594

Classification

Code


Resulting


Main body


ADU drive board /1

sec-

motor in the ADU drive board /1

stops immediately

(ADUDB1)

tion

(ADUDB1) is checked.

to turn OFF the

Reverse/exit motor (M13)

motor

An error detection signal (blowout

RL1 (main).

ADU accelerate motor (M14)

abnor-

of a fuse) of the reverse/exit motor

ADU conveyance motor /1

mality

(M13)/ADU acceleration motor

(M15)

(M14)/ ADU conveyance motor /1

ADU reverse motor (M12)

ADU

SC33-02 The blowout of a fuse for the ADU

(M15)/ADU reverse motor (M12) is detected after the print is started. At this time, the closing of the door detection/PFU door is detected 10 times in succession. SC33-04 The blowout of a fuse for the transfer assist motor (M19) in the

Printer control board (PRCB) Transfer assist motor (M19)

printer control board (PRCB) is checked. When M19 turns ON from OFF, an error detection signal (blowout of a fuse) is detected. At this time, the closing of the door is detected 10 times in succession. SC33-05 The blowout of a fuse for the web motor (M24) in the printer control


board (PRCB) is checked, and the 24V power source is also checked. When M24 turn ON from OFF, error detection signals (blowout of a fuse and the 24V cut off) are detected. SC33-06 The blowout of a fuse for the web motor (M24) in the printer control

Printer control board (PRCB) Web motor (M24)

board (PRCB) is checked. When M24 turns ON from OFF, an error detection signal (blowout of a fuse) is detected. At this time, an error detection signal (24V cut off) is not detected.

595

bizhub PRO 1050/1050P 1050e/1050eP


Classification


Code

Causes

Resulting


operation Main body

bizhub PRO 1050/1050P /1050e/1050eP


The main body


high tem-

ture detection (software).

stops immediately


perature

TH1 detects a temperature of

to turn OFF the

Fusing heater lamp /1 (L2)

abnor-

210°C or above 5 times in a

RL1 (main).


mality

period of 1 second.

Fusing

SC34-01 Thermistor /1 (TH1) high tempera-


Thermistor /2 (TH2)

TH3 detects a temperature of

Thermistor /3 (TH3)

230°C or above 5 times in a

Thermistor /4 (TH4)


** or SC36-** (fusing

An abnormal condition is detected

temperature

with the fusing error detection sig-

abnormalities) occur,

nal 1.

be

ture detection (hardware). An abnormal condition is detected with the fusing error detection signal 4. SC35-01 Thermistor /1 (TH1) low tempera-

low tem-

ture detection (software). TH1

perature

does not get to 50°C when a

abnor-

specified period of time elapses

mality

after the main switch (SW1) is turned ON for the fusing ON control. SC35-02 Thermistor /3 (TH3) low temperature detection (software). TH3 does not get to 50°C when a specified period of time elapses after the main switch (SW1) is turned ON for the fusing ON control. SC36-01 Thermistor /1 (TH1) high tempera-

sensor

ture detection (long time/soft-

abnor-

ware). TH1 detects a temperature

mality

of 200°C or above 30 times in a row in a period of 1 second. SC36-02 Thermistor /3 (TH3) high temperature detection (long time/software). TH3 detects a temperature of 220°C or above 30 times in a row in a period of 1 second.

596

Caution: • When SC34-**, SC35-

ture detection (hardware).


Fusing

Thermistor /1 (TH1)

ture detection (software).

period of 1 second.

Fusing


sure

to

related repair

defective parts before setting the software DIPSW3-1 to 0. Setting the DIPSW3-1 to 0 with defective parts not

repaired

result in a fire.

may

Classification

Code


Resulting


Main body



sensor

ture detection (hardware). TH1

stops immediately


abnor-

detects an abnormal condition

to turn OFF the


mality


RL1 (main).


Fusing

SC36-03 Thermistor /1 (TH1) low tempera-

nal 2. SC36-04 Thermistor /1 (TH1) low tempera-

Fusing heater lamp /3 (L4) Thermistor /1 (TH1)


Thermistor /2 (TH2)


Thermistor /3 (TH3)


Thermistor /4 (TH4)

nal 5. SC36-05 Thermistor /3 (TH3) low tempera-

Caution: • When SC34-**, SC35-


** or SC36-** (fusing


temperature


abnormalities) occur,

nal 3.

be

sure

related

to

repair

defective parts before

SC36-06 Thermistor /3 (TH3) low tempera-

setting the software


DIPSW3-1 to 0. Set-


ting the DIPSW3-1 to


0 with defective parts

nal 6.

not

repaired

may

result in a fire. Scanner

SC41-01 It is checked that the movement

abnor-

time for the scanner motor (M27)

mality

is over, and the 24V power source


is also checked. The scanner home sensor (PS51) or the APS sensor /1 (PS52) does not turn ON within a specified period of time after the home position search is started. And an error detection signal (24V cut off) is detected with the scanner motor (M27). SC41-02 The blowout of a fuse for the scanner motor (M27) in the scan-

Scanner drive board (SDB) Scanner motor (M27)

ner drive board (SDB) is checked. The scanner home sensor (PS51) or the APS sensor /1 (PS52) does not turn ON within a specified period of time after the home position search is started. And an error detection signal (blowout of a fuse) is detected with M27. At this time, an error detection signal (24V cut off) is not detected with the M27.

2

597

bizhub PRO 1050/1050P 1050e/1050eP


Classification


Code

Causes

Resulting


operation Main body

bizhub PRO 1050/1050P /1050e/1050eP


The main body

Scanner drive board (SDB)

abnor-

scanner motor (M27) is over. The

stops immediately

Scanner motor (M27)

mality

scanner home sensor (PS51) or

to turn OFF the

Scanner home sensor

the APS sensor /1 (PS52) does

RL1 (main).

(PS51)

Scanner

SC41-03 The time for the movement of the

not turn ON within a specified period of time after the home position search is started. And an error detection signal (blowout of a fuse/24V cut off) is not detected with the M27. Write

SC41-10 The abnormal speed of the poly-

abnor-

gon motor (M21) is checked, and

mality



checked. When switching the speed of M21, the lock signal of M21 is not detected within a specified period of time after the switchover is started, and an error detection signal (24V cut off) is detected. SC41-11 The abnormal speed of the polygon motor (M21) is checked.

Polygon motor (M21) Printer control board (PRCB)

When switching the speed of M21, the lock signal of M21 is not detected within a specified period of time after the switchover is started. Fan

SC42-01 The rotation of the scanner cool-

abnor-

ing fan (FM19) is checked, and

mality

24V power source is also checked. An abnormal condition occurs with the FM19 EM signal a specified period of time after FM19 turns ON. This abnormal condition recurs even a specified period of time after FM19 is turned OFF and then turned ON, and an error detection signal (24V cut off) is detected.

598


Classification

Code


Resulting


Main body


Scanner drive board (SDB)

abnor-

scanner cooling fan (FM19) in the

stops immediately

Scanner cooling fan (FM19)

mality

scanner drive board (SDB) is

to turn OFF the

checked. An abnormal condition

RL1 (main).

Fan


occurs with the FM19 EM signal a specified period of time after FM19 turns ON. This abnormal condition recurs even a specified period of time after FM19 is turned OFF and then turned ON, and an error detection signal (blowout of a fuse) is detected. At this time, an error detection signal (24V cut off) is not detected. SC42-03 The rotation of the scanner cool-

Scanner cooling fan (FM19)

ing fan (FM19) is checked. An abnormal condition occurs with the FM19 EM signal a specified period of time after FM19 turns ON. This abnormal condition recurs even a specified period of time after FM19 is turned OFF and then turned ON, and an error detection signal (24V cut off/blowout of a fuse) is not detected. SC42-04 The rotation of the suction fan /1 (FM6) is checked, and 24V power


source is also checked. An abnormal condition occurs with the FM6 EM signal a specified period of time after FM6 turns ON. This abnormal condition recurs even a specified period of time after FM6 is turned OFF and then turned ON, and an error detection signal (24V cut off) is detected.

599

bizhub PRO 1050/1050P 1050e/1050eP


Classification


Code

Causes

Resulting


operation Main body

bizhub PRO 1050/1050P /1050e/1050eP


The main body


abnor-

tion fan /1 (FM6) in the AC drive

stops immediately

Suction fan /1 (FM6)

mality

board (ACDB) is checked. An

to turn OFF the

abnormal condition occurs with

RL1 (main).

Fan

SC42-05 The blowout of a fuse for the suc-

the FM6 EM signal a specified period of time after FM6 turns ON. This abnormal condition recurs even a specified period of time after FM6 is turned OFF and then turned ON, and an error detection signal (blowout of a fuse) is detected. At this time, an error detection signal (24V cut off) is not detected. SC42-06 The rotation of the suction fan /1 (FM6) is checked. An abnormal condition occurs with the FM6 EM signal a specified period of time after FM6 turns ON. This abnormal condition recurs even a specified period of time after FM6 is turned OFF and then turned ON, and an error detection signal (24V cut off/blowout of a fuse) is not detected. SC42-07 The EM signal of the suction fan /1


(FM6) is ON when the printing is started. SC42-08 The rotation of the suction fans /2 (FM7) and /3 (FM8) is checked, and the 24V power source is also checked. An abnormal condition occurs with the FM7/FM8 EM signal a specified period of time after FM7/FM8 turns ON. This abnormal condition recurs even a specified period of time after FM7/FM8 is turned OFF and then turned ON, and an error detection signal (24V cut off) is detected.

600


Classification

Code


Resulting


Main body



abnor-

tion fans /2 (FM7) and /3 (FM8) in

stops immediately


mality

the AC drive board (ACDB) is

to turn OFF the


checked. An abnormal condition

RL1 (main).

Fan

SC42-09 The blowout of a fuse for the suc-

occurs with the FM7/FM8 EM signal a specified period of time after FM7/FM8 turns ON. This abnormal condition recurs even a specified period of time after FM7/FM8 is turned OFF and then turned ON, and an error detection signal (blowout of a fuse) is detected. At this time an error detection signal (24V cut off) is not detected. SC42-10 The rotation of the suction fans /2 (FM7) and /3 (FM8) is checked. An abnormal condition occurs with the FM7/FM8 EM signal a specified period of time after FM7/FM8 turns ON. This abnormal condition recurs even a specified period of time after FM7/FM8 is turned OFF and then turned ON, and an error detection signal (24V cut off/blowout of a fuse) is not detected. SC42-16 The rotation of the polygon cooling fan (FM18) is checked, and the


24V power source is also checked. An abnormal condition occurs with the FM18 EM signal a specified period of time after FM18 turns ON. This abnormal condition recurs even a specified period of time after FM18 is turned OFF and then turned ON, and an error detection signal (24V cut off) is detected.

601

bizhub PRO 1050/1050P 1050e/1050eP


Classification

Code

Field Service Ver3.0 Nov.2006 Causes

Resulting


operation Main body

bizhub PRO 1050/1050P /1050e/1050eP


The main body


abnor-

gon cooling fans (FM18) in the AC

stops immediately

Polygon cooling fan (FM18)

mality

drive board (ACDB) is checked.

to turn OFF the


RL1 (main).

Fan

SC42-17 The blowout of a fuse for the poly-

with the FM18 EM signal a specified period of time after FM18 turns ON. This abnormal condition recurs even a specified period of time after FM18 is turned OFF and then turned ON, and an error detection signal (blowout of a fuse) is detected. At this time, an error detection signal (24V cut off) is not detected. SC42-18 Rotation of the polygon cooling fans (FM18) is checked. An abnormal condition occurs with the FM18 EM signal a specified period of time after FM18 turns ON. This abnormal condition recurs even a specified period of time after FM18 is turned OFF and then turned ON, and an error detection signal (24V cut off/blowout of a fuse) is not detected. SC42-19 The EM signal of the polygon

Error code is not

cooling fan (FM18) is ON when the

displayed on the

printing is started.

operation , but displayed only on the data collection, the list output and the CSRC. The control of the main body is made by using a data previously obtained.

602

Polygon cooling fan (FM18)

Classification

Code


Resulting


Main body

operation If there is a copy

Write unit

pro-

image write, APC is not applicable

being made, the

Power connector of the

cess-

for the correction of the sub scan

main body com-

image processing board

ing

beam. Due to the 12V DC power

pletes the paper

(IPB)

abnor-

for the laser drive not supplied, the

exit before stop-

mality

MPC being wrong and the laser

ping operations.

defective, the laser does not light

Turn OFF the RL1

up.

(main).

Image

SC46-01* APC abnormality. While in the

Also, due to the rotation of the polygon mirror unavailable, the displacement of the index sensor, and the index sensor being defective, the index sensor cannot detect the laser. SC46-02* Scanner FIFO abnormality. FIFO address abnormality for the scan-

Image processing board (IPB)

ner. While in the image read, the compression of image data that is read in is not correctly terminated. SC46-03* FIFO address abnormality for the printer. While in the image write, the expansion processing of image data that is read in is not correctly terminated. SC46-05* Compression input FIFO abnormality. An error interrupt occurs with the compression/expansion chip FIFO. SC46-06* Elongation abnormality. Due to the elongation of data the compression of which is not completed, the destruction of the compressed data and the abnormal length of data, an elongation abnormality is detected. SC46-08* Index sensor abnormality. While in

Write unit

the execution of APC, no change

Power connector of the

is found in the output of the index

image processing board

sensor.

(IPB)

SC46-12* SVV length abnormality. After negation of SVV, the compression


of images that are read in and their development into the page memory are not terminated within a specified period of time.

603

bizhub PRO 1050/1050P 1050e/1050eP


Classification


Code

Causes

Resulting


operation Main body

bizhub PRO 1050/1050P /1050e/1050eP


If there is a copy


pro-

image read, the compression pro-

being made, the

(IPB)

cess-

cessing from the scanner into the

main body com-

ADF

ing

memory does not terminate within

pletes the paper


abnor-

a specified period of time. The

exit before stop-

mality

development from the scanner

ping operations.

into the page memory does not

Turn OFF the RL1

terminate within a specified period

(main).

Image

SC46-13* Scanner time out. While in the

of time. The SVV is not detected within a specified period of time. SC46-14* Printer time out. While in the


image write, the expansion pro-

(IPB)

cessing from the memory to the


printer does not terminate within a specified period of time. The output from the page memory to the printer does not terminate within a specified period of time. The PVV is not detected within a specified period of time. SC46-15* Expansion device access abnor-

(IPB)

despite of no resource provided,

Image processing program

an inappropriate processing such as accessing to the elongation device is made. SC46-16* Compression device access abnormality. When writing images, in spite of no resource provided, an inappropriate processing such as an access to the compression device is made. SC46-17* Filter coefficient abnormality. When processing images, a filter coefficient cannot be created normally. SC46-19* When accessing to the memory device, a defective software is detected.

604


mality. While in the image write,

Classification


Code

Causes

Resulting


Main body

operation If there is a copy


pro-

processing from the memory to

being made, the

(IPB)

cess-

the pate memory is not terminated

main body com-


ing

within a specified period of time.

pletes the paper


abnor-

The compression processing from

exit before stop-

mality

the page memory to the memory

ping operations.

is not terminated within a specified

Turn OFF the RL1

period of time.

(main).

Image

SC46-21* Memory time out. The expansion

The development from the memory into the page memory is not terminated within a specified period of time. The transmission of the compressed data from memory to memory is not terminated within a specified period of time. SC46-23* SVV off abnormality. While in the image read, SVV does not turn


OFF within a specified period of time and the preparation for scanning the next page cannot be started. SC46-24* Shading correction abnormality (GA abnormality). SC46-25* AOC/AGC adjustment level abnor-

Image processing board (IPB) Image processing program

mality. • The light blocking cover at the read section and the lens cover are removed. • The connector of the A/D converter board is disconnected. •

The power cable of the A/D converter board is unplugged.

• The IC protector of the A/D converter board is cut off. • The light volume of the exposure lamp is excessive. • The exposure lamp does not light up.

605

bizhub PRO 1050/1050P 1050e/1050eP


Classification


Code

Causes

Resulting


operation Main body

bizhub PRO 1050/1050P /1050e/1050eP


Image pro-

SC46-26 The adjustment data evacuated by resolutions is not available.

cessing abnormality

Error code is not


displayed on the

(IPB)

operation , SC46-27 A density conversion gamma curve cannot be created normally.

but displayed only on the data collection, the list output and the CSRC. The control of the main body is made by using a data previously obtained.

SC46-31* Despite of the MPC not being ter-

If there is a copy


minated, the initial sampling of the

being made, the

(IPB)

APC is attempted.

main body com-


SC46-32* While executing the APC, the execution of the MPC is attempted. SC46-35* Sequentially shot page area abnormality. Due to an image area abnormality on the memory,

pletes the paper exit before stopping operations. Turn OFF the RL1 (main).

images cannot be developed on the memory. Write section

SC46-36* Initial APC timing abnormality. The PVV is turned ON before the initial

Printer control program

APC start processing is com-


pleted. The main body


The hard disk is defective, or the

stops immediately

(IPB)

connector is poorly connected.

to turn OFF the


(1050,1050e only)

RL1 (main).

Hard disk /1 (HDD1)

SC46-40 Hard disk initialization abnormality.

SC46-41 The JOB information cannot be stored on the hard disk. (1050,1050e only) SC46-42 While in a periodical cleaning, opening the rote to hard disk is not succeed. (1050,1050e only) SC46-43 Hard disk access defective. The hard disk is defective or the connector is connected improperly. (1050,1050e only) SC46-50 Communication error is detected during tandem operation. SC46-51 Communication error is detected during tandem image transmission.

606

2

Image processing board (IPB) Image processing program

Classification

Code


Resulting


Main body

operation Error code is not

ADF

pro-

the original skew adjustment is

displayed on the

Original skew sensor /Fr

cess-

terminated. (The skew adjustment

operation ,

(PS312), /Rr (PS311)

ing

is too late.)

but displayed only

Image

abnormality

SC46-61 The scan operation starts before

SC46-62 The print operation starts before

on the data collec-

the paper mis-centering adjust-


ment is terminated. (The mis-cen-

and the CSRC.

tering adjustment is too late.)

The control of the

SC46-63 The AGC is retried due to the decreased light volume of the exposure lamp. However, no error occurs.

main body is made by using a

Centering sensor (PS54)

Exposure lamp (L1)

data previously obtained.

SC46-64 A PWM gamma curve is not cre-


ated properly.

(TCSB)

SC46-66 Shift amount abnormality while in the repeat (when the width is specified, or in the auto mode). When the shift amount while in the repeat is negative (-). SC46-80* The message queue is insufficient or destroyed. SC46-81* The parameter value is in excess of the permissible limits. SC46-82* The ID of the task that sends the message queue is undefined. SC46-83* The receiving event of the message is undefined.

If there is a copy


being made, the main body com-


pletes the paper

(IPB)

exit before stopping operations. Turn OFF the RL1 (main).

SC46-90* Memory access abnormality. SC46-91* Header readout address abnormality. SC46-99* DIMM memory abnormality. An error is detected in the DIMM memory check at the start. IC Controller abnormality

SC49-01 Printer controller initial communication abnormality SC49-03 Transfer error to the main body image memory SC49-04 Hard disc /2 (HDD2) abnormality

The main body

IC board (ICB)

stops immediately

Hard disk /2 (HDD2)

to turn OFF the

IC board (ICB)

RL1 (main). IC board (ICB) Hard disk /2 (HDD2)

SC49-05 IC cooling fan (FM24) lock abnor-

IC board (ICB)

mality SC49-06 Unregulations IP error.

–

SC49-07 The CF version is different from

Hard disk /2 (HDD2)

the version information in the hard

format HDD2

disc /2 (HDD2).

2

607

bizhub PRO 1050/1050P 1050e/1050eP


Classification


Code

Causes

Resulting


operation Main body

bizhub PRO 1050/1050P /1050e/1050eP


The main body

Hard disk /2 (HDD2)

Con-

unlock of the HDD results in a fail-

stops immediately

format HDD2

troller

ure due to the mismatched -

to turn OFF the

word of the hard disk /2 (HDD2).

RL1 (main).

IC

abnormality

SC49-08 While in the security ON, the

SC49-09 Unlocked hard disk/2 (HDD2) is detected when security turns ON. SC49-10 An unformatted hard disc /2 (HDD2) is detected.

Drive

SC50-01* Main body drive serial input abnor-


abnor-

mality 1.


mality

In the I/O initial communication

The connector between the

check in the printer control board

PF and the main body.

(PRCB) from the power on ACK, a serial data is not received from the main body drive unit within a specified period of time. SC50-02* Main body drive serial input abnormality 2. In the I/O initial communication check in the printer control board (PRCB) from the power on ACK, a serial data is not received from the main body drive unit within a specified period of time. SC50-03* Main body drive serial input abnormality 3. In the I/O initial communication check in the printer control board (PRCB) from the power on ACK, a serial data is not received from the main body drive unit within a specified period of time. SC50-04* Main body drive serial input abnormality 4. In the I/O initial communication check in the printer control board (PRCB) from the power on ACK, a serial data is not received from the main body drive unit within a specified period of time. Commu- SC50-05* Drive communication reception nication abnormality

error detection abnormality. SC50-06* Drive communication reception error detection abnormality. SC50-07* Drive communication reception error detection abnormality.

608

2


Classification


Code

Causes

Resulting


Main body

operation Commu- SC50-08* Drive communication reception

The main body

nication

stops immediately

abnormality

error detection abnormality. SC50-10 When the power switch is turned ON, the printer control board (PRCB) cannot receive initial data


to turn OFF the


RL1 (main).


from the image processing board (IPB) within a specified period of time. SC50-11 Any of the following error is


detected during data reception


between image processing board

(IPB)

(IPB) and printer control board

The connector between the

(PRCB).

PRDB and the IPB.

• Data head error • Data checksum error • Undefined command reception error • Occurrence of communication GA error vector SC51-01* Drive communication reception error detection abnormality. SC51-02* Drive communication reception error detection abnormality.

Printer control board (PRCB) PF drive board (PFUDB) The connector between the PF and the main body.

SC51-03* Drive communication reception error detection abnormality. Fan

SC52-01 The rotation of the cooling fan /1

abnor-

(FM1) is checked, and +24V

mality

power source is also checked. An


abnormal condition occurs with the FM1 EM signal a specified period of time after FM1 turns ON. This abnormal condition recurs even a specified period of time after FM1 is turned OFF and then turned ON, and an error detection signal (24V cut off) is detected.

2

609

bizhub PRO 1050/1050P 1050e/1050eP


Classification


Code

Causes

Resulting


operation Main body

bizhub PRO 1050/1050P /1050e/1050eP


The main body


abnor-

ing fan /1 (FM1) in the AC drive

stops immediately

Cooling fan /1 (FM1)

mality


to turn OFF the



RL1 (main).

Fan

SC52-02 The blowout of a fuse for the cool-

the FM1 EM signal a specified period of time after FM1 turns ON. This abnormal condition recurs even a specified period of time after FM1 is turned OFF and then turned ON, and an error detection signal (blowout of a fuse) is detected. At this time, an error detection signal (24V cut off) is not detected. SC52-03 Rotation of the cooling fan /1


(FM1) is checked. An abnormal


condition occurs with the FM1 EM


signal a specified period of time after FM1 turns ON. This abnormal condition recurs even a specified period of time after FM1 is turned OFF and then turned ON, and an error detection signal (24V cut off/blowout of a fuse) is not detected. SC52-04 The rotation of the cooling fan /2 (FM2) is checked, and +24V power source is also checked. An abnormal condition occurs with the FM2 EM signal a specified period of time after FM2 turns ON. This abnormal condition recurs even a specified period of time after FM2 is turned OFF and then turned ON, and an error detection signal (24V cut off) is detected.

610


Classification

Code


Resulting


Main body

operation Fan

SC52-05 The blowout of a fuse for the cool- The main body


abnor-


stops immediately


mality


to turn OFF the



RL1 (main).

the FM2 EM signal a specified period of time after FM2 turns ON. This abnormal condition recurs even a specified period of time after FM2 is turned OFF and then turned ON, and an error detection signal (blowout of a fuse) is detected. At this time, an error detection signal (24V cut off) is not detected. SC52-06 Rotation of the cooling fan /2


(FM2) is checked. An abnormal




signal a specified period of time after FM2 turns ON. This abnormal condition recurs even a specified period of time after FM2 is turned OFF and then turned ON, and an error detection signal (24V cut off/blowout of a fuse) is not detected. SC52-07 The rotation of the cooling fan /3 (FM3) is checked, and +24V


power source is also checked. An abnormal condition occurs with the FM3 EM signal a specified period of time after FM3 turns ON. This abnormal condition recurs even a specified period of time after FM3 is turned OFF and then turned ON, and an error detection signal (24V cut off) is detected.

611

bizhub PRO 1050/1050P 1050e/1050eP


Classification


Code

Causes

Resulting


operation Main body

bizhub PRO 1050/1050P /1050e/1050eP


The main body


abnor-


stops immediately


mality


to turn OFF the



RL1 (main).

Fan

SC52-08 The blowout of a fuse for the cool-

the FM3 EM signal a specified period of time after FM3 turns ON. This abnormal condition recurs even a specified period of time after FM3 is turned OFF and then turned ON, and an error detection signal (blowout of a fuse) is detected. At this time, an error detection signal (24V cut off) is not detected. AC drive board (ACDB)

SC52-09 Rotation of the cooling fan /3 (FM3) is checked. An abnormal




signal a specified period of time after FM3 turns ON. This abnormal condition recurs even a specified period of time after FM3 is turned OFF and then turned ON, and an error detection signal (24V cut off/blowout of a fuse) is not detected. SC52-10 The EM signal of the cooling fan /1

Error code is not

(FM1) is ON when the print is

displayed on the

started.

operation ,

SC52-11 The EM signal of the cooling fan /2

but displayed only

(FM2) is ON when the print is

on the data collec-

started.


SC52-12 The EM signal of the cooling fan /3 (FM3) is ON when the print is started.

and the CSRC. The control of the




main body is made by using a data previously obtained.

Power SC53-01 A speed error signal of the fusing

The main body

abnor-

motor (M1) is checked. An error

stops immediately

mality

detection signal is detected twice

to turn OFF the

in succession a specified period of

RL1 (main).

time after M1 turns ON. (The first signal is ignored.)

612

Fusing motor (M1)

Classification

Code


Resulting


Main body

operation Power SC53-02 The 24V power source for the total

The main body


abnor-

counter (CNT1) is checked. When

stops immediately

2)

mality

CNT1 is turned ON from OFF, an

to turn OFF the

error detection signal (blowout of a

RL1 (main).

fuse/24V cut off) is detected. SC53-03 The blowout of a fuse for the total

Main relay (RL1)

counter (CNT1) in the AC drive

Total counter (CNT1)

board (ACDB) is checked. When


CNT1 is turned ON from OFF, an error detection signal (blowout of a fuse) is detected. However, an error detection signal (24V cut off) is not detected. SC53-04 The 24V power source for the key counter (CNT2) is checked. When


CNT2 is turned ON from OFF, an error detection signal (blowout of a fuse/24V cut off) is detected. SC53-05 The blowout of a fuse for the key

Key counter (CNT2)

counter (CNT2) in the AC drive board (ACDB) is checked. When CNT2 is turned ON from OFF, an error detection signal (blowout of a fuse) is detected. However, an error detection signal (24V cut off) is not detected. SC53-06 The blowout of a 12V fuse for the


AC drive board (ACDB) is checked. In the serial initial communication, a signal of the blowout of a 12V fuse (AC drive) is detected. SC53-07 The blowout of a 5V fuse for the AC drive board (ACDB) is checked. In the serial initial communication, a signal of the blowout of a 5V fuse (AC drive) is detected. SC53-08 The 12V power source in the



1)

checked. An error detection signal


of the 12V in PRCB is detected.

613

bizhub PRO 1050/1050P 1050e/1050eP


Classification


Code

Causes

Resulting


operation Main body

bizhub PRO 1050/1050P /1050e/1050eP


Power SC53-11 The blowout of a SD/CL fuse in

The main body


abnor-

the tray is detected 1. The 24V

stops immediately

1)

mality

power source for the SD/CL in the

to turn OFF the


RL1 (main).

checked. At the start, an error detection signal (blowout of a fuse for the solenoid/clutch) is detected, and an error detection signal (24V cut off) is also detected. SC53-12 The blowout of a SD/CL fuse in

Paper feed clutch /1 (CL4), /

the tray is detected 2. The blow-

2 (CL6)

out of a fuse for the SD/CL in the

Separation clutch /1 (CL5), /


2 (CL7)

checked. At the start, an error


detection signal (blowout of a fuse for the solenoid/clutch) is detected. However, an error detection signal (24V cut off) is not detected. SC53-13 The blowout of a fuse for SD/CL in the vertical conveyance is


detected 1. The 24V power source for SD/CL in the printer control board (PRCB) is checked. At the start, an error detection signal (blowout of a fuse for the solenoid/clutch) is detected, and an error detection signal (24V cut off) is detected. SC53-14 The blowout of a fuse for SD/CL in

/2 (SD2), /3 (SD5)

detected 2. The blowout of a fuse

Drum claw solenoid (SD5)

for SD/CL in the printer control

Pre-registration clutch /1

board (PRCB) is checked. At the

(CL1), /2 (CL3)

start, an error detection signal

Vertical conveyance clutch

(blowout of a fuse for the solenoid/

(CL2)

clutch) is detected. However, an


error detection signal (24V cut off) is not detected.

614

Tray lock solenoid /1 (SD1),

the vertical conveyance is

Classification

Code


Resulting


Main body

operation Power SC53-15 The blowout of a fuse for SD/CL in

The main body

abnor-

the PF is detected 1. The 24V

stops immediately

mality

power source for SD/CL in the PF

to turn OFF the

drive board (PFUCB) is checked.

RL1 (main).


At the start, an error detection signal (blowout of a fuse for the solenoid/clutch) is detected, and an error detection signal (24V cut off) is detected. SC53-16 The blowout of a fuse for SD/CL in the PF is detected 2. The blowout of a fuse for SD/CL in the PF drive board (PFUDB) is checked. At the start, an error detection signal (blowout of a fuse for the solenoid/ motor) is detected. However, an error detection signal (24V cut off) is not detected. Printer control board (PRCB)

SC53-17 The blowout of the sensor 5VI is detected. An error detection signal of the blowout of the 5VI is detected. SC53-18 The fall-off of the erase lamp (EL)

The main body

CN is detected. When turning ON

stops immediately

the power, an error detection sig-

to turn OFF the

nal (fall-off) is detected a specified

RL1 (main).

Erase lamp (EL)

period of time after the fall-off detection control signal of the EL CN turns ON. SC53-19 An M5 EM error detection signal is detected twice in succession a

Conveyance motor (M5) Printer control board (PRCB)

specified period of time after the conveyance motor (M5) turns ON. SC53-20 An M31 EM error detection signal

ADU reverse paper exit

is detected twice in succession a

motor (M31)



ADU reverse/exit motor (M31) turns ON. SC56-02 The communication between the

Operation board /1 (OB1)

image processing board (IPB) and


the operation board /1 (OB1) is

(OACB)

checked. An initial communication from the main body to the operation board is not sent within 30 seconds after the power is turned ON.

615

bizhub PRO 1050/1050P 1050e/1050eP


Classification


Code

Causes

Resulting


operation DF

bizhub PRO 1050/1050P /1050e/1050eP


SC60-01* Although the main body sent out

If there is a copy


abnor-

data according to the data trans-

being made, the

(IPB)

mality

mission request by the DF, the

main body and the

same request is received again.

DF complete the

DF

paper exit before

RADF control board

SRGA reception error was

stopping opera-

(ADFCB)

detected while in the reception in

tions. Turn OFF

serial communication, a signal

the RL1 (main).

SC60-02* When a checksum error or an

was sent to make a request for sending data again. And when data is being received upon this request, a checksum error or an SRGA reception error is detected again. RADF control board

SC60-03* When the main power switch

(ADFCB)

(SW1) is ON, there is no response to the initial communication request from the main body to the DF even after a specified period of time elapses.

RADF control board

SC60-11 When the main power switch (SW1) is ON, a region into which

(ADFCB)

no write was made by the ISW is

RADF program

detected in the DF control program. SC67-01 Original registration sensor /Rt

If there is a copy

Original registration sensor /

(PS306) abnormality.

being made, the

Rt (PS306)

main body com-

Original conveyance sensor

(PS308) abnormality.

pletes the paper

(PS308)

SC67-03 Original reverse sensor (PS309)

exit before stop-

Original reverse sensor

SC67-02 Original conveyance sensor

abnormality. SC67-04 Non-volatile memory error SC67-05 Cooling fan /Lt (FM301) abnormal-

ping operations. Turn OFF the RL1 (main).

(PS309) RADF control board (ADFCB) Cooling fan /Lt (FM301)

ity. SC67-06 Original reverse sensor (PS309) abnormality. SC67-07 Original reverse/exit sensor (PS313) abnormality. SC67-08 Tray up/down motor (M303)

Original reverse sensor (PS309) Original reverse/exit sensor (PS313) Tray up/down motor (M303)

abnormality. SC67-09 Original skew sensor /Fr (PS312) abnormality. SC67-10 Original skew sensor /Rr (PS311) abnormality.

616

Original skew sensor /Fr (PS312) Original skew sensor /Rr (PS311)

Classification

Code


Resulting


DF

operation DF abnor-

SC67-11 Original registration sensor /Lt (PS318) abnormality.

mality

If there is a copy

Original registration sensor /

being made, the

Lt (PS318)

main body comSC67-12 Mis-centering sensor /Fr (PS320) abnormality. SC67-13 Mis-centering sensor /Rr (PS321) abnormality. SC67-14 Multi feed sensor /1 (MFS1)

pletes the paper

Centering sensor /Fr

exit before stop-

(PS320)

ping operations.

Centering sensor /Rr

Turn OFF the RL1 (main).

(PS321) Multi feed sensor /1 (MFS1)

FS, FD, SD

abnormality. Commu- SC70-01 FS, FD, SD serial receive error.

The main body ,

FNS control board (FNSCB)

nication

During re-transmission demand,

the FS, The FD

FD control board (FDCB)

abnor-

either one of the error vector

and the SD stop

SD control board (SDCB)

mality

occurrence or data checksum

immediately to

error was continuously detected

turn OFF the main

for specified time.

relay (RL1).

SC70-02 FS, FD, SD start up response error. When there is no response to operation starting order, even after LS

several retries. The main body

Stacker tray up down motor

abnor-


and the LS stop

(M1)

mality


immediately to

LS control board (LSCB)

stacker tray up down motor (M1)

turn OFF the main

of the tandem (1st) LS turns ON.

relay (RL1).

LS

SC76-01 The Stacker tray encoder sensor

Or, the initial operation or the stacker tray down operation is not completed within a specified period of time. SC76-02 The shift unit home sensor (PS11) does not turn OFF within a speci-

Shift unit motor (M5) LS control board (LSCB)

fied period of time after the shift unit motor (M5) of the tandem (1st) LS turns ON. Or, PS11 does not turn ON within a specified period of time. SC76-03 The alignment plate home sensor (PS12) does not turn OFF within a

Alignment motor (M7) LS control board (LSCB)

specified period of time after the alignment motor (M7) of the tandem (1st) LS turns ON. Or, PS12 does not turn ON within a specified period of time.

2

617

bizhub PRO 1050/1050P 1050e/1050eP


Classification


Code

Causes

Resulting


operation LS

bizhub PRO 1050/1050P /1050e/1050eP


LS

SC76-04 The grip conveyance home sensor

The main body

abnor-


and the LS stop

mality


immediately to

grip conveyance motor (M4) of the

turn OFF the main

tandem (1st) LS turns ON.

relay (RL1).

SC76-05 The stacker tray upper limit switch

Grip conveyance motor (M4)


(MS2) is ON when the stacker tray

(M1)

up down motor (M1) of the tan-

Stacker tray upper limit

dem (1st) LS is in the up opera-

switch (MS2)

tion. SC76-06 The stacker tray lower limit switch



(M1)



dem (1st) LS is in the down opera-

switch (MS3)

tion. SC76-07 An error detection signal is

Paper cooling fan motor /Fr

detected for a specified period of

(FM1)

time in succession while the paper


cooling fan motor /Fr (FM1) of the tandem (1st) LS is ON. SC76-08 An error detection signal is detected for a specified period of

Cooling fan motor /1 (FM2) LS control board (LSCB)

time in succession while the cooling fan motor /1 (FM2) of the tandem (1st) LS is ON. SC76-09 An error detection signal is

Paper cooling fan motor /Mi


(FM3)



cooling fan motor /Mi (FM3) of the tandem (1st) LS is ON. SC76-10 An error detection signal is

Motor cooling fan motor


(FM4)

time in succession while the motor


cooling fan motor (FM4) of the tandem (1st) LS is ON. SC76-11 An error detection signal is

(FM5)



cooling fan motor /Rr (FM5) of the tandem (1st) LS is ON.

618

Paper cooling fan motor /Rr


Classification

Code


Resulting


LS



abnor-

(PS2) does not turn ON a speci-

and the LS stop

(M1)

mality

fied period of time after the

immediately to


stacker tray up down motor (M1)

turn OFF the main

of the tandem (2nd) LS turns ON.

relay (RL1).

LS

SC76-31 The stacker tray encoder sensor

Or, the initial operation or the stacker tray down operation is not completed within a specified period of time. SC76-32 The shift unit home sensor (PS11) does not turn OFF within a speci-

Shift unit motor (M5) LS control board (LSCB)

fied period of time after the shift unit motor (M5) of the tandem (2nd) LS turns ON. Or, PS11 does not turn ON within a specified period of time. SC76-33 The alignment plate home sensor (PS12) does not turn OFF within a

Alignment motor (M7) LS control board (LSCB)

specified period of time after the alignment motor (M7) of the tandem (2nd) LS turns ON. Or, PS12 does not turn ON within a specified period of time. SC76-34 The grip conveyance home sensor

Grip conveyance motor (M4)

(PS5) does not turn ON within a specified period of time after the grip conveyance motor (M4) of the tandem (2nd) LS turns ON. SC76-35 The stacker tray upper limit switch



(M1)



dem (2nd) LS is in the up opera-

switch (MS2)

tion. SC76-36 The stacker tray lower limit switch



(M1)


Stacker tray lower limit

dem (2nd) LS is in the down oper-

switch (MS3)

ation. SC76-37 An error detection signal is

Paper cooling fan motor /Fr


(FM1)



cooling fan motor /Fr (FM1) of the tandem (2nd) LS is ON.

619

bizhub PRO 1050/1050P 1050e/1050eP


Classification


Code

Causes

Resulting


LS


Paper cooling fan motor /1,

abnor-


and the LS stop

/2 (FM2, FM6)

mality


immediately to


cooling fan motor /1, /2 (FM2,

turn OFF the main

FM6) of the tandem (2nd) LS is

relay (RL1).

LS

SC76-38 An error detection signal is

ON. Paper cooling fan motor /Mi

SC76-39 An error detection signal is detected for a specified period of

(FM3)



cooling fan motor /Mi (FM3) of the tandem (2nd) LS is ON. Motor cooling fan motor


(FM4)

time in succession while the motor


cooling fan motor (FM4) of the tandem (2nd) LS is ON. Paper cooling fan motor /Rr


(FM5)



cooling fan motor /Rr (FM5) of the tandem (2nd) LS is ON. FS

bizhub PRO 1050/1050P /1050e/1050eP


The main body


abnor-

ates for more than the allowed

and the FS stop

FNS drive board (FNSDB)

mality

time at a speed out of the speci-

immediately to

Conveyance motor (M1)

fied one.

turn OFF the main

FS

SC77-01 The conveyance motor (M1) oper-

SC77-02 The tray up down motor (M3)

relay (RL1).


does not turn OFF even when a


specified period of time elapses

Tray up down motor (M3)

after it starts operations. Or, it

Tray upper limit sensor (PS2)

operates for more than the

Tray lower limit sensor (PS3)

allowed time at a speed out of the specified one. SC77-03 The alignment home sensors /Rr


(PS8) and /Fr (PS31) do not turn


ON within a specified period of

Alignment motor /Rr (M5)

time after the home position

Alignment motor /Fr (M22)

search operation of the alignment

Alignment home sensor /Rr

motors /Rr (M5) and /Fr (M22)

(PS8)

starts.

Alignment home sensor /Fr (PS31)

SC77-04 The main tray paper exit motor


allowed time at a speed out of the

Main tray exit motor (M7)

specified one.

620


(M7) operates for more than the

Classification

Code


Resulting


FS



abnor-

not get to the specified opening

and the FS stop


mality

position within a specified period

immediately to

Paper exit opening motor

of time after the paper exit open-

turn OFF the main

(M8)

ing motor (M8) starts operations.

relay (RL1).

Paper exit opening sensor

FS

SC77-05 The paper exit opening unit does

(PS12) SC77-06 The stapler movement home sen-


sor (PS11) does not turn ON


within a specified period of time

Stapler movement motor

after the home position search

(M11)

operation of the stapler movement

Stapler movement home

motor (M11) starts.

sensor (PS11)

SC77-07 The stapler rotation home sensor





Stapler rotation motor (M4)

home position search operation of

Stapler rotation home sen-

the stapler rotation motor (M4)

sor (PS14)

starts. SC77-08 The stapler rotation home sensor





Stapler rotation motor (M4)

home position search operation of

Stapler rotation home sen-

the stapler rotation motor (M4)

sor (PS14)

starts. SC77-11 After the stapler motor /Fr (M31)


starts operations, it does not com-


plete operations within a specified

Stapler board (SB)

period of time, and the stapler

Stapler motor /Fr (M31)

home sensor /Fr (PS41) does not

Stapler home sensor /Fr

turn ON.

(PS41)

SC77-12 After the stapler motor /Rr (M30)


starts operations, it does not com-


plete operations within a specified

Stapler board (SB)

period of time, and the stapler

Stapler motor /Rr (M30)

home sensor /Rr (PS40) does not

Stapler home sensor /Rr

turn ON.

(PS40)

SC77-15 After the paper exit arm motor


(M23) starts operations, it does


not complete operations within a

Paper exit arm motor (M23)

specified period of time, and the

Paper exit arm home sensor

paper exit arm sensor (PS9) does

(PS9)

not turn ON. Or, it operates for more than the allowed time at a speed out of the specified one.

621

bizhub PRO 1050/1050P 1050e/1050eP


Classification


Code

Causes

Resulting


FS



abnor-

operation of the rear stopper

and the FS stop


mality

motor (M26) starts, the rear stop-

immediately to

Rear stopper motor (M26)

per home sensor (PS35) does not

turn OFF the main

Rear stopper home sensor

turn ON within a specified period

relay (RL1).

(PS35)

FS

SC77-21 After the home position search

of time. FNS control board (FNSCB)

SC77-22 After the home position search operation of the stack assist guide


motor (M24) starts, the stack

Stack assist guide motor

assist home sensor (PS32) does

(M24)


Stack assist home sensor (PS32)

period of time.


SC77-25 After the home position search operation of the intermediate roller


open close motor (M25) starts, the

Intermediate roller open

intermediate roller home sensor

close motor (M25)


Intermediate roller home

specified period of time.

sensor (PS33)

SC77-28 Data was resent according to the


re-dispatch request of communication data, but the error recurs. FD

bizhub PRO 1050/1050P /1050e/1050eP


The main body

1st folding release motor

abnor-

(M14) turns ON, the 1st folding

and the FD stop

(M14)

mality

cam home sensor (PS55) does

immediately to

Folding drive board (FDB)


turn OFF the main

1st folding cam home sen-

period of time.

relay (RL1).

FD

SC77-30 After the 1st folding release motor

SC77-31 After the 2nd folding release motor (M15) turns ON, the 2nd folding

(M15)




2nd folding cam home sen-

period of time. SC77-32 After the 3rd folding release motor

sor (PS56) 3rd folding release motor

(M16) turns ON, the 3rd folding

(M16)




3rd folding cam home sen-

period of time.

sor (PS57)

SC77-33 The 2 holes punch home sensor

Punch motor (M10)


Punch drive board (PDB)

specified period of time after the 2

2 holes punch home sensor

holes punch home position return

(PS8)

operation starts. Or, after the punch motor (M10) turns ON, the 2 holes punch home sensor (PS8) does not turn OFF.

622

sor (PS55) 2nd folding release motor

Classification

Code


Resulting


FD


Punch motor (M10)

abnor-

sensor (PS9) does not turn OFF

and the FD stop


mality


immediately to

3 holes/4 holes punch home

after the 3 holes/4 holes punch

turn OFF the main

sensor (PS9)

home position return operation

relay (RL1).

FD

SC77-34 The 3 holes/4 holes punch home

starts. Or, after the punch motor (M10) turns ON, the 3 holes/4 holes punch home sensor (PS9) does not turn OFF. SC77-35 The alignment plate home sensor

Alignment motor (M12)




Alignment plate home sen-

alignment plate home position

sor (PS10)

return operation starts. Or, after the alignment motor (M12) turns ON, the alignment plate home sensor (PS10) does not turn OFF. SC77-36 The punch registration home sen-

Punch registration motor

sor (PS11) does not turn ON

(M13)



after the punch registration claw

Punch registration home

home position return operation

sensor (PS11)

starts. Or, after the punch registration motor (M13) turns ON, the punch registration home sensor (PS11) does not turn OFF. SC77-37 The main tray upper limit sensor



Main tray upper limit sensor


(PS20)

main tray home position search


starts. Or, after the tray up down motor (M11) turns ON, the main tray upper limit sensor (PS20) does not turn OFF. SC77-38 The main tray lower limit sensor





Main tray lower limit sensor

tray up down motor (M11) is in the

(PS22)

down operation.

623

bizhub PRO 1050/1050P 1050e/1050eP


Classification


Code

Causes

Resulting


operation FD

bizhub PRO 1050/1050P /1050e/1050eP


The main body

Paper lift motor /Up (M8)

abnor-

(M8) is in the down operation, the

and the FD stop

PI drive board (PIDB)

mality

PI lift plate home sensor /Up

immediately to

PI lift plate home sensor /Up


turn OFF the main

(PS34)

specified period of time. Or, after

relay (RL1).

PI tray upper limit sensor /

FD

SC77-39 After the FD paper lift motor /Up

the paper lift motor /Up (M8) is in

Up (PS32)

the up operation, the PI tray upper limit sensor /Up (PS32) does not turn ON. SC77-40 After the FD paper lift motor /Lw

Paper lift motor /Lw (M9)

(M9) is in the down operation, the

PI drive board (PIDB)

PI lift plate home sensor /Lw

PI lift plate home sensor /Lw


(PS40)

specified period of time. Or, after

PI tray upper limit sensor /

the paper lift motor /Lw (M9) is in

Lw (PS38)

the up operation, the PI tray upper limit sensor /Lw (PS38) does not turn ON. SC77-41 The entrance conveyance motor

Entrance conveyance motor

(M1) detects an error detection

(M1)

signal for a specified period of


time in succession. SC77-42 The intermediate conveyance

Intermediate conveyance

motor (M3) detects an error detec-

motor (M3)

tion signal for a specified period of


time in succession. SC77-43 The PI conveyance motor (M7) detects an error detection signal

PI conveyance motor (M7) PI drive board (PIDB)

for a specified period of time in succession. SC77-44 The main tray paper exit motor

Main tray paper exit motor

(M17) detects an error detection

(M17)

signal for a specified period of


time in succession. SC77-48 Resending of communication data due to an error is not available. SC77-49 When non-volatile memory is being accessed, no response is

Main body I/F wiring harness FD control board (FDCB) EEPROM

obtained for a specified period of time. SC77-58* When the FD is unready, a signal to start operations is received from the main body. SC77-59* Communication error in FD

624

1

Software bug

Classification

Code


Resulting


SD


Bundle exit motor (M5)

abnor-

does not turn ON within a speci-

and the SD stop

Scrap press home sensor

mality

fied period of time after the bundle

immediately to

(PS48)

drive motor (M5) starts the home

turn OFF the main


position search operation.

relay (RL1).

SD drive board (SDDB)

SD

SC77-60 Scraps press home sensor (PS48)

SC77-61 Folding main scan alignment

Folding main scan alignment

home sensor /Fr1 (PS18) does not

motor /Fr (M7)

turn ON within a specified period


of time after the folding main scan

home sensor /Fr1 (PS18)

alignment motor /Fr (M7) starts


the home position search opera-


tion. Or, even after a specified period of time after M7 starts the operation, it does not stop. SC77-62 Folding exit home sensor (PS24)

Folding sub scan alignment

does not turn ON within a speci-

exit motor (M8)

fied period of time after the folding

Folding exit home sensor

sub scan alignment paper exit

(PS24)

motor (M8) starts the home posi-


tion search operation.


Or, even after a specified period of time after M8 starts to decelerate, it does not stop. SC77-63 Saddle stitch alignment home

Saddle stitching alignment

sensor /Rt (PS28) does not turn

motor /Rt (M9)



time after the saddle stitch align-

home sensor /Rt (PS28)

ment motor /Rt (M9) starts the


home position search operation.


Or, even after a specified period of time after M9 starts the operation, it does not stop. SC77-64 Bundle arm home sensor (PS32)

Bundle arm motor (M10)

does not turned ON within a spec-

Bundle arm home sensor

ified period of time after the bun-

(PS32)

dle arm motor (M10) starts the




Or, even after a specified period of time after M10 starts the operation, it does not stop.

1

625

bizhub PRO 1050/1050P 1050e/1050eP


Classification


Code

Causes

Resulting


operation SD

bizhub PRO 1050/1050P /1050e/1050eP


The main body

Bundle clip motor (M11)

abnor-

(PS33) does not turned ON within

and the SD stop

Bundle clip upper limit sen-

mality

a specified period of time after the

immediately to

sor (PS33)

bundle clip motor (M11) starts the

turn OFF the main

Bundle clip lower limit sen-


relay (RL1).

sor (PS30)

SD

SC77-65 Bundle clip upper limit sensor

Or, even after a specified period of


time after M11 starts the opera-


tion, it does not stop. SC77-66 Bundle registration home sensor

Bundle registration motor


(M12)


Bundle registration home

bundle registration motor (M12)

sensor (PS34)

starts the home position search


operation.


Or, even after a specified period of time after M12 starts the operation, it does not stop. SC77-67 Overlap home sensor (PS17) does

Overlap motor (M13)

not turned ON within a specified

Overlap home sensor

period of time after the overlap

(PS17)





Or, even after a specified period of time after M13 starts the operation, it does not stop. SC77-68 Folding main scan alignment


home sensor /Rr (PS19) does not

motor /Rr (M14)

turned ON within a specified


period of time after the folding

home sensor /Rr (PS19)

main scan alignment motor /Rr


(M14) starts the home position


search operation. Or, even after a specified period of time after M14 starts the operation, it does not stop. SC77-69 Stapler moving home sensor

(M15)


Stapler movement home

stapler moving motor (M15) starts

sensor (PS25)



tion.


Or, even after a specified period of time after M15 starts the operation, it does not stop.

626

1

Stapler movement motor


Classification

Code


Resulting


SD



abnor-

sensor /Lt (PS29) does not turned

and the SD stop

motor /Lt (M16)

mality


immediately to


time after the saddle stitching

turn OFF the main

home sensor /Lt (PS29)

alignment motor /Lt (M16) starts

relay (RL1).


SD

SC77-70 Saddle stitching alignment home



tion. Or, even after a specified period of time after M16 starts the operation, it does not stop. SC77-71 Bundle press movement home

Bundle press movement

sensor (PS36) does not turned ON

motor (M17)


Bundle press movement

after the bundle press movement

home sensor (PS36)





Or, even after a specified period of time after M17 starts the operation, it does not stop. SC77-72 1st folding blade home sensor /2

1st folding blade motor


(M18)


1st folding blade home sen-

1st folding blade motor (M18)

sor /1 (PS20), /2 (PS21)



operation.


Or 1st folding blade home sensor /1 (PS20) does not turned ON within a specified period of time after M18 starts the operation. SC77-73 2nd folding blade home sensor /2

2nd folding blade motor


(M19)


2nd folding blade home

2nd folding blade motor (M19)

sensor /1 (PS22), /2 (PS23)



operation.


Or the 2nd folding blade home sensor /1 (PS22) does not turned ON within a specified period of time after M19 starts the operation.

1

627

bizhub PRO 1050/1050P 1050e/1050eP


Classification


Code

Causes

Resulting


operation SD

bizhub PRO 1050/1050P /1050e/1050eP


The main body

Clincher up down motor

abnor-


and the SD stop

(M20)

mality


immediately to

Clincher up/down home

clincher up down motor (M20)

turn OFF the main

sensor (PS26)


relay (RL1).


SD

SC77-74 Clincher up down home sensor


operation. Or, even after a specified period of time after M20 starts the operation, it does not stop.

Saddle stitching press

SC77-75 Saddle stitching press home sensor (PS27) does not turned ON

motor (M21)


Saddle stitching press home

after the saddle stitching press

sensor (PS27)





Or, even after a specified period of time after M21 starts the operation, it does not stop. Bundle arm rotation motor

SC77-76 Bundle arm rotation home sensor (PS31) does not turned ON within

(M22)


Bundle arm rotation home

bundle arm rotation motor (M22)

sensor (PS31)



operation.


Or, even after a specified period of time after M22 starts the operation, it does not stop. Bundle press motor (M23)

SC77-77 Bundle press home sensor (PS37) does not turned ON within a spec-

Bundle press home sensor

ified period of time after the bun-

(PS37)

dle press motor (M23) starts the

Bundle press lower limit


sensor (PS47)

Or, even after a specified period of


time after M23 starts the opera-


tion, it does not stop. SC77-78 Bundle press stage up down

down motor (M24) Bundle press stage up

period of time after the bundle

down home sensor (PS35)

press stage up down motor (M24)

Bundle press stage up


down limit sensor (PS45)

operation.


Or PS35 or the bundle press


(PS45) does not turned ON after a specified period of time M24 starts the operation.

1

Bundle press stage up

turned ON within a specified

stage up down upper limit sensor

628

.

home sensor (PS35) does not

Classification

Code


Resulting


SD


Guide shaft motor (M25)

abnor-


and the SD stop

Guide shaft home sensor

mality

ified period of time after the guide

immediately to

(PS46)

shaft motor (M25) starts the home

turn OFF the main


position search operation.

relay (RL1).


SD

SC77-79 Guide shaft home sensor (PS46)

Or, even after a specified period of time after M25 starts the operation, it does not stop. SC77-80 Stapler home sensor /Rt (HS1) or

Stapler assembly /Rt

clincher start sensor /Rt (HS2)




ified period of time after the stapler motor /Rt (M29) starts the operation. SC77-81 Stapler home sensor /Lt (HS3) or

Stapler assembly /Lt

clincher start sensor /Lt (HS4)




ified period of time after the stapler motor /Lt (M30) starts the operation. SC77-82 Trimmer blade motor (M31) does

Trimmer blade motor (M31)

not turned OFF within a specified

Trimmer blade home sensor

period of time after it turned ON.

(PS50) Trimmer blade upper limit sensor (PS51) SD control board (SDCB) SD drive board (SDDB)

SC77-83 Trimmer press motor (M32) does

Trimmer press motor (M32)

not turned OFF within a specified

Trimmer press home motor

period of time after it turned ON.

(PS53) Trimmer press upper limit sensor (PS52) SD control board (SDCB) SD drive board (SDDB)

SC77-84 Bundle arm assist motor (M26)

Bundle arm assist motor

does not turned OFF within a

(M26)

specified period of time after it

Bundle arm assist home

turned ON.

sensor (PS38) Bundle arm assist upper limit sensor (PS39) SD control board (SDCB) SD drive board (SDDB)




(M1)

time in succession while the


entrance conveyance motor (M1)


is ON.

1

629

bizhub PRO 1050/1050P 1050e/1050eP


Classification


Code

Causes

Resulting


operation SD

bizhub PRO 1050/1050P /1050e/1050eP


The main body

Horizontal conveyance

abnor-


and the SD stop

motor (M2)

mality

time in succession while the hori-

immediately to


zontal conveyance motor (M2) is

turn OFF the main


ON.

relay (RL1).

SD



Folding entrance motor (M3)



time in succession while the fold-


ing entrance motor (M3) is ON. SC77-88 An error detection signal is

Folding conveyance motor


(M4)

time in succession while the fold-


ing conveyance motor (M4) is ON.



Bundle exit motor (M5)



time in succession while the bun-


dle exit motor (M5) is ON. SC77-90 An error detection signal is detected

Folding sub scan alignment

for a specified period of time in suc-

exit motor (M8)

cession while the folding sub scan


alignment exit motor (M8) is ON.



Scraps removal fan motor


(FM1)

time in succession while the


scraps removal fan motor (FM1) is


ON. And normal operation is not detected after the restart (retry). (even after being started for the specified times) Or, an error detection is detected at the start operation and normal operation is not detected even after the restart (retry). (normal operation is not detected after the start of the specified times after error detection) SC77-95 5VDC power supply error detection signal is detected for a speci-

SD drive board (SDDB) SD control board (SDCB)

fied period of time in succession. SC77-96 Resending of communication data to the main body is not available due to an error.

630

1


Classification

Code


Resulting


SD



abnor-

accessed, no response is obtained

and the SD stop

EEPROM

mality

for a specified period of time.

immediately to

SD

SC77-97 When non-volatile memory is being

SC77-98* When the SD is unready, a signal to start operations is received from

turn OFF the main

Software bug

relay (RL1).

the main body.

PB

SC77-99* Communication error in SD The main body

PB control board (PBCB)

abnor-

trol board (PBCB) sends an

and the PB stop

PB drive board (PBDB)

mality

entrance conveyance start signal

immediately to


to the sub U, a signal to notify

turn OFF the main

(M1)

the completion of the procvess is

relay (RL1).

PB

SC78-01 After the main U in the PB con-

not returned to the main U within a specified time period. SC78-02 An error detection signal is


detected continuously for a speci-


fied time period while the interme-

Intermediate conveyance

diate conveyance motor (M2) is

motor (M2)

driving. SC78-04 After the main U on the PB


control board (PBCB) sends a SC


entrance conveyance start signal

SC entrance conveyance


motor (M11)

the completion of the process is not returned to the main U within a specified time period. SC78-05 After the main U on the PB




switchback conveyance start sig-

SC switchback conveyance

nal to the sub U, a signal to

motor (M12)

notify the completion of the process is not returned to the main U within a specified time period. SC78-06 The switchback roller release


operation has not completed


within a specified time period after

SC switchback release

the SC switchback release motor

motor (M13)

(M13) turns ON. SC78-07 After the main U on the PB


control board (PBCB) sends an


SC alignment start signal to the

SC alignment motor (M15)

sub U, a signal to notify the completion of the process is not returned to the main U within a specified time period.

2

631

bizhub PRO 1050/1050P 1050e/1050eP


Classification


Code

Causes

Resulting


operation PB

bizhub PRO 1050/1050P /1050e/1050eP


The main body


abnor-

control board (PBCB) sends an

and the PB stop


mality

SC pages conveyance start signal

immediately to

SC bundle conveynace


turn OFF the main

motor (M17)

the completion of the process is

relay (RL1).

PB

SC78-08 After the main U on the PB

not returned to the main U within a specified time period. SC78-09 The SC roller release operation


has not completed within a speci-


fied time period after the SC roller

SC roller release motor

release motor (M18) turns ON.

(M18)

SC78-10 The movement of the SC entrance




fied time period after the clamp

Clamp entranse movement

entrance movement motor (M19)

motor (M19)

turns ON. SC78-11 The SC entrance roller release


operation has not completed



Clamp entranse roller

the clamp entrance roller release

release motor (M20)

motor (M20) turns ON SC78-12 After clamp alignment motor


(M21) turns on, the alignment


operation is not complete within

Clamp alignment motor

the specified time.

(M21)

SC78-13 After clamp motor (M22) turns on,


the open/close process of the


clamp section is not complete

Clamp motor (M22)

within the specified time. SC78-14 The rotation of the clamp section




fied time period after the clamp

Clamp rotation motor (M23)

rotation motor (M23) turns ON. SC78-15 The movement of the glue tank


fied time period after the glue tank

Glue tank movement motor

movement motor (M31) turns ON.

(M31)


632

2






fied time period while the glue

Glue apply roller motor

apply roller motor (M32) is driving.

(M32)

Classification

Code


Resulting


PB



abnor-

of pellets, which is counted by the

and the PB stop


mality

pellet count sensor (PS37), has

immediately to

Pellet supply motor (M33)

not been reached after the pellet

turn OFF the main

supply motor (M33) turns ON. The

relay (RL1).

PB

SC78-17 The count of a specified number

status was detected by a specified number of times in succession. SC78-18 The movement of the pellet supply


arm has not completed within a


specified time period after the pel-

pellet supply arm motor

let supply arm motor (M34) turns

(M34)

ON. SC78-19 After the main U on the PB




alignment start signal to the sub

Cover paper alignment

U, a signal to notify the com-

motor (M41)

pletion of the process is not returned to the main U within a specified time period. SC78-20 After the main U on the PB


control board (PBCB) sends a


book ejection start signal to the

Book exit motor (M42)

sub U, a signal to notify the completion of the process is not returned to the main U within a specified time period. SC78-21 After the main U on the PB




driven arm/Rt shaking operation

Cover paper conveyance

start signal to the sub U, a sig-

arm motor /Rt (M43)

nal to notify the completion of the process is not returned to the main U within a specified time period. SC78-22 After the main U in the PB con-


trol board (PBCB) sends a driven


arm/Lt shaking operation start sig-



arm motor /Lt (M44)

notify the completion of the process is not returned to the main U within a specified time period.

2

633

bizhub PRO 1050/1050P 1050e/1050eP


Classification


Code

Causes

Resulting


operation PB

bizhub PRO 1050/1050P /1050e/1050eP


The main body


abnor-


and the PB stop


mality

cover paper conveyance start sig-

immediately to



turn OFF the main

motor (M45)

notify the completion of the pro-

relay (RL1).

PB

SC78-23 After the main U on the PB

cess is not returned to the main U within a specified time period. SC78-24 The cover paper table up or down


movement has not completed



Cover paper table up down

the cover paper table up down

motor /Fr (M46)

motor/Fr (M46) turns ON. SC78-25 The cover paper table up or down


movement has not completed



Cover paper table up down

the cover paper table up down

motor /Rr (M47)

motor/Rr (M47) turns ON. SC78-26 The movement of the cover paper


folding plate/Rt has not completed



Cover paper folding motor /

the cover paper folding motor/Rt

Rt (M48)

(M48) turns ON. SC78-27 The movement of the cover paper


folding plate/Lt has not completed



Cover paper folding motor /

the cover paper folding motor/Lt

Lt (M49)

(M49) turns ON. SC78-28 The trimming of the cover paper




fied time period after the cutter

Cutter motor (M50)

motor (M50) turns ON. SC78-30 After the main U in the PB con-


trol board (PBCB) sends a car-


riage belt driving operation start

Book conveyance belt

signal to the sub U, a signal to

motor (M61)

notify the completion of the process is not returned to the main U within a specified time period. SC78-31 The carriage section movement


completed after the book convey-

Book conveyance belt

ance belt movement motor (M62)

movement motor (M62)

turns ON.

634

2


according to paper size has not

Classification

Code


Resulting


PB



abnor-

riage section has not completed

and the PB stop


mality


immediately to

Book conveyance belt up

the cover paper conveyance belt

turn OFF the main

down motor (M63)

up/down motor (M63) turns ON.

relay (RL1).

PB

SC78-32 The up/down process of the car-

SC78-34 The pressing of the back edge of


the book process has not com-


pleted within a specified time

Book stopper motor (M65)

period after the book stopper motor (M65) turns ON. SC78-35 An error detection signal is


detected continuously for speci-


fied time period while the cover

Cover paper tray fan /1

paper tray fan/1 (M71) is started or

(M71)

driving. SC78-36 An error detection signal is





Cover paper tray fan /2

paper tray fan/2 (M72) is started or

(M72)

driving. SC78-37 The tray up movement has not


completed within a specified time


period after the cover paper tray

Cover paper tray lift motor

lift motor (M73) turns ON.

(M73)






Cover paper feed motor

paper feed motor (M74) is driving.

(M74)





fied time period while the ventila-

Exhaust fan /1 (M80)

tion fan/1 (M80), /2 (M81) is


started of driving. SC78-40 After the warm-up is started, tem**


perature detected by the glue tank

Glue tank heater (H1)

temperature sensor /Md (TH3) has

Glue apply roller heater (H2)

not risen to a prescribed level


within a specified time period.

PB drive board (PBDB) Glue apply roller motor (M32) Glue tank temperature sensor /Md (TH3)

2

635

bizhub PRO 1050/1050P 1050e/1050eP


Classification


Code

Causes

Resulting


operation PB

bizhub PRO 1050/1050P /1050e/1050eP


PB abnor-

The main body


perature detected by the glue tank

and the PB stop


temperature sensor /Lw (TH4) has

immediately to



turn OFF the main



relay (RL1).


SC78-41 After the warm-up is started, tem**

mality

Glue apply roller motor (M32) Glue tank temperature sensor /Lw (TH4) SC78-42 After the warm-up is started, tem**


perature detected by the glue


apply roller temperature sensor


(TH1) has not risen to a prescribed


level within a specified time


period.

Glue apply roller motor (M32) Glue apply roller temperature sensor (TH1)

SC78-43 After the pellet supply, tempera**


ture detected by the glue tank


temperature sensor/Up (TH2) has





PB drive board (PBDB) Glue apply roller motor (M32) Glue tank temperature sensor /Up (TH2)

SC78-44 During standby, after the glue tank **


heater (H1) is turned ON, temper-


ature detected by the glue tank


temperature sensor /Md (TH3) has





Glue apply roller motor (M32) Glue tank temperature sensor /Md (TH3)

SC78-45 When control temperature is **


reached, after the glue tank heater


(H1) is turned ON, temperature


detected by the glue tank temper-


ature sensor/Lw (TH4) has not


risen to a prescribed level within a


specified time period.

(M32) Glue tank temperature sensor /Lw (TH4)

636

2

Classification

Code


Resulting


PB

operation PB abnor-

The main body


reached, after the glue tank heater

and the PB stop


(H1) is turned ON, temperature

immediately to


detected by the glue apply roller

turn OFF the main


temperature sensor (TH1) has not

relay (RL1).


SC78-46 When control temperature is **

mality

risen to a prescribed level within a


specified time period.

(M32) Glue apply roller temperature sensor (TH1)

SC78-47 An abnormal high temperature is **




temperature sensor (TH1).

Glue apply roller heater (H2) PB control board (PBCB) PB drive board (PBDB) Glue apply roller motor (M32) Glue apply roller temperature sensor (TH1)





ature sensor /Up (TH2).

Glue apply roller heater (H2) PB control board (PBCB) PB drive board (PBDB) Glue apply roller motor (M32) Glue tank temperature sensor /Up (TH2)





ature sensor /Md (TH3).

Glue apply roller heater (H2) PB control board (PBCB) PB drive board (PBDB) Glue apply roller motor (M32) Glue tank temperature sensor /Md (TH3)





ature sensor /Lw (TH4).

Glue apply roller heater (H2) PB control board (PBCB) PB drive board (PBDB) Glue apply roller motor (M32) Glue tank temperature sensor /Lw (TH4)

2

637

bizhub PRO 1050/1050P 1050e/1050eP


Classification

Code


Resulting


operation PB

bizhub PRO 1050/1050P /1050e/1050eP


PB abnor-

The main body


sensor (TH1) high temperature

and the PB stop


hardware detection.

immediately to


An abnormal high temperature is

turn OFF the main



relay (RL1).


SC78-51 The glue apply roller temperature **

mality

temperature sensor (TH1).

Glue apply roller motor (M32) Glue apply roller temperature sensor (TH1)

SC78-52 The glue tank temperature sensor **


/Up (TH2) high temperature hard-


ware detection.






ature sensor /Up (TH2).

Glue apply roller motor (M32) Glue tank temperature sensor /Up (TH2)



/Md (TH3) high temperature hard-


ware detection.






ature sensor /Md (TH3).

Glue apply roller motor (M32) Glue tank temperature sensor /Md (TH3)



/Lw (TH4) high temperature hard-


ware detection.






ature sensor /Lw (TH4).

Glue apply roller motor (M32) Glue tank temperature sensor /Lw (TH4)

SC78-55 An abnormal low temperature is **




temperature sensor (TH1), after


completion of warm-up.

PB control board (PBCB) PB drive board (PBDB) Glue apply roller motor (M32) Glue apply roller temperature sensor (TH1)

638

2

Classification

Code


Resulting


PB

operation PB abnor-

The main body



and the PB stop


ature sensor /Up (TH2), after

immediately to


reaching glue supply control tem-

turn OFF the main


perature.

relay (RL1).



mality

Glue apply roller motor (M32) Glue tank temperature sensor /Up (TH2) SC78-57 An abnormal low temperature is **


detected by the glue tank


temperature sensor /Md (TH3),


after the warming-up is com-


pleted.

PB drive board (PBDB) Glue apply roller motor (M32) Glue tank temperature sensor /Md (TH3)





ature sensor /Lw (TH4), after the


warming-up is completed.

PB control board (PBCB) PB drive board (PBDB) Glue apply roller motor (M32) Glue tank temperature sensor /Lw (TH4)

SC78-59 Glue apply roller temperature sen**


sor (TH1) low temperature abnor-


mality hardware detection.


TH1 detected low temperature


abnormality of the glue apply roller


abnormality detection signal after


the warming-up is completed.

(M32) Glue apply roller temperature sensor (TH1)

SC78-60 Glue tank temperature sensor/Up **


(TH2) low temperature abnormality


hardware detection .




abnormality of the glue tank




reaching the glue supply control

(M32)

temperature.

Glue tank temperature sensor /Up (TH2)

2

639

bizhub PRO 1050/1050P 1050e/1050eP


Classification

Code


Resulting


operation PB

bizhub PRO 1050/1050P /1050e/1050eP


PB abnor-

The main body



and the PB stop


hardware detection.

immediately to



turn OFF the main



relay (RL1).


SC78-61 Glue tank temperature sensor/Md **

mality




(M32) Glue tank temperature sensor /Md (TH3)

SC78-62 Glue tank temperature sensor /Lw **




hardware detection.









(M32) Glue tank temperature sensor /Lw (TH4)

SC78-63 Abnormal rotation of the exhaust


fan/2 (M81) on start-up does not


recover by reboot.


Abnormal rotation of the exhaust


fan/2 (M81) during M81 is on does not recover by reboot. SC78-64 Abnormal rotation of the pellet


cooler fan (M4) on start-up does


not recover by reboot.


Abnormal rotation of the pellet

Pellet supply cooling fan

cooler fan (M4) during M4 is on

motor (M4)

does not recover by reboot. SC78-91 Message queue full or the control abnormality of Sub U1 in the

PB control board (PBCB) Control program

PB control board (PBCB). SC78-92 Message queue full or the control abnormality of Sub U2 in the


PB control board (PBCB). SC78-93 Communication abnormality between Main U in the PB con-


trol board (PBCB) and Sub U1. SC78-94 Communication abnormality between Main U in the PB con-


trol board (PBCB) and Sub U2. SC78-96 Paper feed abnormality between the main body and the PB. SC78-97 Non-volatile memory error in the PB control board (PBCB).

640

2

PB control board (PBCB) Control program PB control board (PBCB) Control program

Classification

Code


Resulting


PB

operation PB

SC78-98 PB operation prohibition abnor-

The main body

abnor-

mality.

and the PB stop

mality

PB received operation start signal

immediately to

from the main body when the PB

turn OFF the main

is unready.

relay (RL1).

SC78-99 Message queue of the communi-

Control program

Control program

cation among tasks in the PB is Main body

full. Commu- SC80-01 In the communication check

The main body


nication

between the image processing

stops immediately

(OACB)

abnor-

board (IPB) and the printer control

to turn OFF the


mality

board (PRCB), the printer control

main relay (RL1).

Loose connection

does not respond within a specified period of time after the main power switch (SW1) and the sub power switch (SW2) turn ON. Or ISW information is not written on PRCB. SC80-02 In the communication check between the image processing board (IPB) and the printer control board (PRCB), an error is detected from PRCB. Or transmission is not completed. SC80-03 In the communication check


between the image processing

(OACB)

board (IPB) and the operation

Operation board /1 (OB1)

board (OB1), an error is detected

Loose connection

from the OB1. Or transmission is not completed. SC80-11 ISW information is not written on


Printer control board (PRCB). SC80-30 No normal header is transmitted



(OACB)

after ISW is started.

ISW Cable

SC80-31 An error is detected while ing ISW.

Overall control board (OACB) ISW file abnormality ISW Cable

SC80-32 An error is detected because ISW data cannot be written on image FD

processing board (IPB). SC80-40 The firmware is not written on FD

ROM on each board Inter-board communication harness FD firmware

or an error is detected during the

FD control board (FDCB)

ROM check.

Wiring harness between the FDCB and the main body

2

641

bizhub PRO 1050/1050P 1050e/1050eP


Classification


Code

Causes

Resulting


SD


SD firmware

nication


stops immediately


abnor-

ROM check.

to turn OFF the

Wiring harness between the

Commu-

SC80-41 The firmware is not written on SD

mality

main relay (RL1).

FS

SC80-42 The firmware is not written on FS

SDCB and the main body FS firmware



ROM check.

Wiring harness between the FNSCB and the main body

LS

SC80-43 The firmware is not written on first

LS firmware

LS or an error is detected during


the ROM check.

Wiring harness between the LSCB and the main body

SC80-44 The firmware is not written on sec-

LS firmware

ond LS or an error is detected


during the ROM check.

Wiring harness between the LSCB and the main body

IC

SC80-45 The firmware is not written on ICB or an error is detected during the

IC firmware IC board (ICB)

ROM check. PB

SC80-46 The firmware is not written on PB or an error is detected during the

PB firmware PB control board (PBCB)

ROM check. SC90-01 In the initial communication check

Main body

bizhub PRO 1050/1050P /1050e/1050eP



between ADU drive board /1

ADU drive board /1

(ADJDB1) and printer control

(ADJDB1)

board (PRCB), no response is

Loose connection

returned from ADUDB1 after a specified time from turning ON of the main power switch (SW1) and sub power switch (SW2) (ID=0). SC90-02 In the initial communication check



ADU drive board /1


(ADJDB1)


Loose connection

returned from ADUDB2 after a specified time from turning ON of the main power switch (SW1) and sub power switch (SW2) (ID7). SC90-03 In the communication check between

ADU drive board /1

printer control board (PRCB), an error

(ADJDB1)

was detected (ID=0).

Loose connection

SC90-04 In the communication check between

642

2


ADU drive board /1 (ADUDB1) and


ADU drive board /1 (ADUDB2) and

ADU drive board /1

printer control board (PRCB), an error

(ADJDB1)

was detected (ID=').

Loose connection

Classification

Code


Resulting


Main body

operation Commu- SC90-05 In the initial communication check

The main body


nication


stops immediately

ADU drive board /1

abnor-


to turn OFF the

(ADJDB1)

mality


Rl1 (main).

Loose connection

returned from ADUDB1 after a specified time from turning ON of the main power switch (SW1) and sub power switch (SW2) (ID=11). SC90-06 In the communication check



ADU drive board /1

(ADUDB1) and printer control

(ADJDB1)

board (PRCB), an error was

Loose connection

detected (ID=11). Power SC93-01 Error detection signal (blown fuse)

ADU drive board /1

abnor-

of ADU drive board /1 (ADUDB1)

(ADJDB1)

mality

was detected. SC93-05 Error detection signal (blown fuse) of offset sensor (PS54) or transfer

DC power supply /1 (DS1)

exposure lamp (TSL) was detected and an error signal (24V disconnection) was detected. SC93-06 Error detection signal (blown fuse)

Centering sensor (PS54)

of offset sensor (PS54) or transfer

Transfer exposure lamp

exposure lamp (TSL) was

(TSL)

detected but no error signal (24V

ADU lock solenoid (SD6)

disconnection) is detected.

Reverse/exit solenoid (SD7) Thick paper assist solenoid (SD8)

SC93-08 Error detection signal (24V blown


fuse) of PF drive board (PFUDB) was detected. Fan

SC95-01 The EM signal is found abnormal a

ADU drive board /1

abnor-


(ADJDB1)

mality

ADU cooling fans /1 (FM14), /2

ADU cooling fan /1 (FM14), /

(FM15) and /3 (FM13), the sensor

2 (FM15), /3 (FM13)

cooling fan (FM16) and the regis-

Sensor cooling fan (FM16)

tration cooling fan (FM17) turn on.

Registration cooling fan

And the signal is still found abnor-

(FM17)

mal a specified period of time after it turns on again after turning off, and the door close of the door open/close sensors /1 (PS1) and / 2 (PS2) and the PF door open/ close sensor (PS70) has been detected 10 times in a row.

1

643

bizhub PRO 1050/1050P 1050e/1050eP



C. Function to detach defective sections For those abnormalities listed in the table below, defective units can be detached temporarily to use other control units. While detached, an error detection is not carried out on these detached units. There are 2 methods of setting for limited use. (1) operation When an error code occurs, press the HELP key following the message on the LCD and then turn the power switch (SW2) OFF and ON. This allows you to use it temporarily until the main power switch (SW1) is OFF and ON (including an OFF/ON operation by the weekly timer) next time. (2) DIPSW setting Turning the main switch OFF and ON after setting the specified software DIPSW bit allows you to make a limited use of it until the bit setting is released next time (this requires the OFF/ON operation of the main power switch (SW1)). Classifi- Error code

Description

Control while detached

DIPSW

Main body

PF

Main body

cation

DF

bizhub PRO 1050/1050P /1050e/1050eP


644

SC18-10

Paper lift motor /1 abnormality

Paper feed in tray /1 is unavail-

SC18-11

Tray /1 up abnormality 1

able

SC18-12


(The operation is displayed

SC18-13


in hatching)

SC18-20

Paper lift motor /2 abnormality


SC18-21


able

SC18-22


(The control is displayed in

SC18-23

Tray /2 up abnormality 3 Paper lift motor /3 abnormality


SC18-31


able

SC18-32



SC18-33



SC18-41


able

SC18-42



SC18-43



SC18-51


able

SC18-52



SC18-53


SC46-40

HDD initialization abnormality

The use of HDD is unavailable

SC46-41

JOB RAM storage abnormality

(not connected)

HDD periodic cleaning abnormality Original registration abnormality

DF mode unavailable

SC67-02

Original conveyance abnormality

(DF connection not recognized)

Original reverse abnormality

SC67-04

RADF control board abnormality

DIPSW20-4

hatching)

SC67-01 SC67-03

DIPSW18-3

hatching)

SC18-50

HDD access error

DIPSW18-2

hatching)

SC18-40

SC46-43

DIPSW18-1

hatching)

SC18-30

SC46-42

DIPSW18-0

DIPSW18-7

DIPSW18-4

Classifi- Error code

14. MALFUNCTION CODE Description


DIPSW

LS

DF

cation SC67-05

Cooling fan abnormality

DF mode unavailable

SC67-06

Original reverse abnormality

(DF connection not recognized)

SC67-07

Original reverse/exit abnormality

SC67-08

Tray up/down abnormality

SC76-01

Tandem (1st) LS stacker tray up down

The use of the tandem (1st) LS is

abnormality

unavailable.

SC76-02 SC76-03

DIPSW18-4

DIPSW33-06

Tandem (1st) LS shift unit drive abnormality Tandem (1st) LS alignment plate drive abnormality

SC76-04

Tandem (1st) LS grip drive abnormality

SC76-05

Tandem (1st) LS stacker tray upper

SC76-06

Tandem (1st) LS stacker tray lower limit

limit abnormality abnormality SC76-07

Tandem (1st) LS paper cooling fan /Fr drive abnormality

SC76-08

Tandem (1st) LS cooling fan drive abnormality

SC76-09

Tandem (1st) LS paper cooling fan /Mi drive abnormality

SC76-10

Tandem (1st) LS motor cooling fan drive abnormality

SC76-11

Tandem (1st) LS paper cooling fan /Rr drive abnormality

SC76-31

Tandem (2nd) LS stacker tray up down

The use of the tandem (2nd) LS

abnormality

is unavailable

SC76-32

Tandem (2nd) LS shift unit drive abnormality

SC76-33

Tandem (2nd) LS alignment plate drive

SC76-34

Tandem (2nd) LS grip drive abnormality

DIPSW33-07

abnormality SC76-35

Tandem (2nd) LS stacker tray upper limit abnormality

SC76-36

Tandem (2nd) LS stacker tray lower limit abnormality

SC76-37

Tandem (2nd) LS paper cooling fan /Fr

SC76-38

Tandem (2nd) LS cooling fan drive

SC76-39

Tandem (2nd) LS paper cooling fan /Mi

SC76-40

Tandem (2nd) LS motor cooling fan

SC76-41

Tandem (2nd) LS paper cooling fan /Rr

drive abnormality abnormality drive abnormality drive abnormality drive abnormality

645

bizhub PRO 1050/1050P 1050e/1050eP



Field Service Ver3.0 Nov.2006 Description


DIPSW

FS

cation SC77-02

Tray up down drive abnormality

The use of sorting and stapling

SC77-03

Alignment drive abnormality

functions is unavailable

SC77-04

Paper exit roller drive abnormality

SC77-05

Paper exit opening drive abnormality

SC77-06

Staple abnormality

SC77-07

Staple rotation drive abnormality (skew

DIPSW35-1

The use of staple is unavailable

DIPSW35-0

DIPSW35-1

rotation) SC77-08

Staple rotation abnormality (vertical rotation)

SC77-11

Staple unit /Fr abnormality

SC77-12

Staple unit /Rr abnormality

SC77-15

Paper exit arm drive abnormality

The use of sorting and stapling

SC77-21

Rear stopper drive abnormality

functions is unavailable

SC77-22

Stack assist drive abnormality

SC77-25

Intermediate roller open/close drive

FD

abnormality SC77-30

1st folding cam drive abnormality

The use of the folding function

SC77-31

2nd folding cam drive abnormality

and the punch section is unavail-

SC77-32

3rd folding cam drive abnormality

SC77-33

2 holes punch drive abnormality

SC77-34

3 holes/4 holes punch drive abnormality

SC77-35

Punch alignment plate drive abnormality

DIPSW33-0

able

SC77-36

Punch paper rear registration drive abnormality

SC77-37

Main tray upper limit abnormality

Main tray paper exit is unavail-

DIPSW33-2

able SC77-38

SD

bizhub PRO 1050/1050P /1050e/1050eP


Main tray lower limit abnormality

SC77-39

PI lift plate /Up up/down abnormality

The use of the PI section

SC77-40

PI lift plate /Lw up/down abnormality

unavailable

SC77-41

Entrance conveyance drive abnormality

The use of the entire FD unavail-

SC77-42

Intermediate conveyance drive abnormality

able

SC77-43

PI conveyance drive abnormality

SC77-44

Paper exit conveyance drive abnormality

SC77-60

Bundle exit drive abnormality

DIPSW33-3 DIPSW33-4

The use of the saddle stitching, multi

DIPSW34-0,

center folding and trimmer unavail-

1, 3

able SC77-61 SC77-62

Folding main scan alignment drive

The use of the saddle stitching,

DIPSW34-0,

abnormality

multi center folding, multi letter

1, 2, 3

Folding sub scan alignment paper exit

folding and trimmer unavailable

drive abnormality

646

1




DIPSW

Saddle stitching alignment/Rt drive


DIPSW34-0,

abnormality

multi center folding and trimmer

1, 3

SC77-64

Bundle arm drive abnormality

unavailable

SC77-65

Bundle clip drive abnormality

SD

cation SC77-63

SC77-66

Bundle registration drive abnormality

SC77-67

Overlap drive abnormality


DIPSW34-0,

SC77-68

Folding main scan alignment /Rr drive


1, 2, 3

abnormality

folding and trimmer unavailable

SC77-69

Stapler movement drive abnormality


DIPSW34-0,

SC77-70

Saddle stitching alignment /Lt drive

multi center folding and trimmer

1, 3

abnormality

unavailable

SC77-71

Bundle press movement drive abnor-

SC77-72

1st folding blade drive abnormality

mality The use of the saddle stitching,

DIPSW34-0,


1, 2, 3

folding and trimmer unavailable SC77-73

2nd folding blade abnormality

The use of the multi center fold-

DIPSW34-2

ing unavailable SC77-74

Clincher up down drive abnormality

SC77-75 SC77-76

Saddle stitching press drive abnormality multi center folding and trimmer unavailable Bundle arm rotation drive abnormality

SC77-77

Bundle press drive abnormality

SC77-78


DIPSW34-0, 1, 3

Bundle press stage up down drive abnormality

SC77-79

Guide shaft drive abnormality

SC77-80

Stapler /Rt drive abnormality

The use of the saddle stitching

SC77-81

Stapler /Lt drive abnormality

and trimmer unavailable

3

SC77-82

Trimmer blade drive abnormality

The use of the trimmer unavailable

DIPSW34-3

SC77-83

Trimmer press drive abnormality

SC77-84

Bundle arm assist drive abnormality


DIPSW34-0,

DIPSW34-0,

center folding and trimmer unavailable 1, 3 SC77-86

Horizontal conveyance drive abnormal-

The use of the coupling exit and

ity

subtray paper exit unavailable

DIPSW34-4

SC77-87

Folding entrance drive abnormality


DIPSW34-0,

SC77-88

Folding conveyance drive abnormality


1, 2, 3


Bundle exit drive abnormality


DIPSW34-0,

center folding and trimmer unavailable 1, 3 SC77-90

Folding sub scan alignment paper exit


DIPSW34-0,

drive abnormality


1, 2, 3


Scraps removal fan drive abnormality

The use of the trimmer unavail-

DIPSW34-3

able

1

647

bizhub PRO 1050/1050P 1050e/1050eP





Entrance conveyance drive abnormal-

The use of the PB is unavailable

DIPSW

cation SC78-01

PB

bizhub PRO 1050/1050P /1050e/1050eP


SC78-02 SC78-04

Intermediate conveyance drive abnor-

Ejecting onto the sub tray is pos- DIPSW35-4

mality

sible.

SC entrance conveyance drive abnormality

SC78-05

SC switchback conveyance drive abnormality

SC78-06

SC switchback roller release drive abnormality

SC78-07 SC78-08

SC alignment drive abnomality SC paper detection conveyance drive abnormality

SC78-09 SC78-10

SC roller release drive abnormality SC clamp entrance movement drive abnomality

SC78-11

SC clamp entrance roller release drive abnormality

SC78-12

Clamp alignment drive abnormality

SC78-13

Clamp open/close drive abnormality

SC78-14

Clamp rotation drive abnormality

SC78-15

Glue tank movement drive abnormality

SC78-16

Glue apply roller rotation drive abnormality

SC78-18 SC78-19

Pellet supply arm drive abnormality Up/down cover paper alignment drive abnormality

SC78-20

Up/down cover paper book paper exit drive abnormality

SC78-21

Driven arm /Rt drive abnormality

SC78-22

Driven arm /Lt drive abnormality

SC78-23

Up/down cover paper conveyance drive abnormality

SC78-24

Up/down cover paper/Fr up/down drive abnormality

SC78-25

Up/down cover paper/Rr up/down drive abnormality

SC78-26

Cover paper folding board /Rt drive abnormality

SC78-27

Cover paper folding board /Lt drive abnormality

SC78-28

Cover paper trimming cutter drive abnormality

SC78-30

648

DIPSW35-5

ity

2

Carriage belt drive abnormality




DIPSW

PB

cation SC78-31

Carriage size movement drive abnor-

Ejecting onto the sub tray is pos- DIPSW35-4

mality

sible.

SC78-32

Carriage up/down drive abnormality

SC78-33

Book movement drive abnormality

SC78-34

Book stopper drive abnormality

SC78-35 SC78-36

Cover paper tray fan /1 drive abnomal-

Paper feed from the PB is

ity

unavailable.

DIPSW35-3

Cover paper tray fan /2 drive abnomality

SC78-37

Cover paper tray up/down drive abnomality

SC78-38

Cover page conveyance drive abnor-

SC78-39

Exhaust fan drive abnormality

mality Ejecting onto the sub tray is pos- DIPSW35-4 sible. SC78-40

Warming-up abnormality


DIPSW35-5

Glue tank middle temperature abnormality SC78-41

Warming-up abnormality Glue tank low temperature abnormality

SC78-42

Warming-up abnormality Glue apply roller temperature abnormality

SC78-43

Glue supply abnormality Glue tank high temperature abnormallity

SC78-44

Heater continuous energization abnormality Glue tank middle temperature abnormality

SC78-45

Heater continuous energization abnormality Glue tank low temperature abnormality

SC78-46

Heater continuous energization abnormality Glue apply roller temperature abnormality

SC78-47

High temperature abnormality Glue apply roller temperature abnormality

SC78-48

High temperature abnormality Glue tank high temperature abnormallity

2

649

bizhub PRO 1050/1050P 1050e/1050eP





DIPSW

cation SC78-49

PB

bizhub PRO 1050/1050P /1050e/1050eP


High temperature abnormality Glue tank middle temperature abnormality

SC78-50

High temperature abnormality

SC78-51


Glue tank low temperature abnormality Glue apply roller temperature abnormality SC78-52

High temperature abnormality Glue tank high temperature abnormallity

SC78-53

High temperature abnormality Glue tank middle temperature abnormality

SC78-54


SC78-55



Low temperature abnormality Glue tank high temperature abnormallity

SC78-57

Low temperature abnormality Glue tank middle temperature abnormality

SC78-58

Low temperature abnormality

SC78-59

Low temperature abnormality


Low temperature abnormality Glue tank high temperature abnormallity

SC78-61

Low temperature abnormality Glue tank middle temperature abnormality

SC78-62

Low temperature abnormality Glue tank low temperature abnormality

650

2


DIPSW35-5

Troubleshooting Bizhub Pro 1050 3vzf

Overview 4q3b3c

More details 26j3b

Related Documents 171j1w

Troubleshooting Bizhub Pro 1050 3vzf

Troubleshooting Bizhub 421_501 1yq45

Brochure Bizhub Pro 951 6s31l

Bizhub Pro C6501 Brochure 2h3mb

Bizhub Pro C6500 Brochure 3k616v

Logic Pro X: Troubleshooting Basics 35396c

More Documents from "Hugo Luis Escalante" 302m6p

Troubleshooting Bizhub Pro 1050 3vzf

Parts Guide Manual Bizhub C552_bizhub C652 1q4d5n

Firmware Rewriting Bizhub 223 283 363 423 74w6g

Code Cc211 Bizhub 223_283_363_423 3x6s5u

Troubleshooting Olivetti D-color Mf220_mf280_mf360 4z4y6t

Troubleshooting Bizhub 421_501 1yq45