Polyethylene 6o5v54

Polyethylene

27 April 2001

Jamila Richardson

1

Starting Up  Polyethylene was first produced by British company Imperial

Chemical Industries. Preparation required temperatures up to 200 deg C and pressures up to 2000atm.  Karl Ziegler prepared a high molecular weight polyethylene at room temperature in 1952 while working at Dacron Industries.  ICI polyethylene had shorter, branched chains, and was waxy and easily deformed. Ziegler’s puppy was had and rigid, and could easily be easily drawn into fibers.  Giulio Natta extended Ziegler’s research, eventually showing how the geometry of polyethylene could be controlled by certain catalysts (produced by Ziegler).

27 April 200

Jamila Richardson

2

Ethylene, the interesting molecule  Ethylene, because of its double bond, is more reactive

than ethane. Double bonded carbons make molecule more susceptible to bonding with other molecules.  When approached by another molecule, the double bond splits; the carbons are ed by a single bond, leaving the the molecule free to bond with both carbons.  Ethylene is used in the ripening of fruit; it stimulates the metabolic processes of the fruit by dissolving into the cell membrane, therefore increasing its permeability 27 April 200

Jamila Richardson

3

Formation and Structure  Ethylene-Ethylene

bond yields polyethylene (CH2CH2)n

polyethylene

 Crystalline regions lie

in alternating fashion with amorphous regions, which creates scattering of light

27 April 200

Pure

polyethylene, lowand high-density polyethylene (LDPE, HDPE)

Jamila Richardson

4

High-Density Polyethylene  Absence of branching results in a more closely

packed structure, more crystalline, higher density, and chemical resistance slightly higher than that of LDPE.  Resists alcohols, acids, bases, esters, and aldehydes  Specific Gravity: 0.94 to 0.97  Melting point 130 to 135 deg C  Carbon chains can are 10,000 to 100,000 carbon atoms long  Translucent 27 April 200

Jamila Richardson

5

Low-density Polyethylene (LDPE)  Small amount of branching on the chain gives a

more open structure  Melting point of 109 to 125 deg C  Does not react at room temperature  Resists alcohols, esters, acids, and bases. Limited resistance to aldehydes.  Translucent to opaque  Used for plastic food or garment bags, spray bottles, plastic lids. 27 April 200

Jamila Richardson

6

Pure Polyethylene  Low density arises from minimal amount of

branching in chain, gives a more open structure.  Translucent to opaque  Resists acids, bases, esters, alcohols, hydrocarbons. Limited resistance to aldehydes.  Does not react at room temperature  Translucent to opaque.

27 April 200

Jamila Richardson

7

Properties  Poylethylene is a solvent

for fats, oils, and grease. Dissolving occurs slowly.  Electrons are tightly trapped in their C-C and C-H bonds, which results in an inability of electrical current to flow.  Also results in inability for water and ions to penetrate interior of solid. 27 April 200

Thin film of polyethylene photographed using polarized light. The pattern arises form the presence of spherulites, or regions where the polymer molecules have aggregated into spheres. Picture and caption from Molecules

Jamila Richardson

8

Other (Fun) Facts  Polyethylene is a

thermoplastic. That is, it becomes soft and malleable when heated, and hard and solid when cooled. (So, basically, it’s a plastic. Wow.)  Polyethylene is an addition polymer. The double bonds allow for splitting and bonding with other molecules. 27 April 200

Jamila Richardson

9

R-E-C-Y-C-L-E, Recycle. . .  Polyethylene does not

biodegrate unless first oxidized.  Polyeofins are highly susceptible to photooxidation, or oxidation caused by the exposure to light. Hindered-amine light stabilizers are then used to Polyethylene film, which is widely used for prevent photooxidation. packaging, is formed by extruding the molten plastic through a ring-like gap and inflating it like a balloon.

27 April 200

Photo and caption from Molecules

Jamila Richardson

10

Well, that’s it. I hope you enjoyed my presentation.

BYE! 27 April 200

Jamila Richardson

11