L293d Motor Driver Datasheet 144228
This document was ed by and they confirmed that they have the permission to share it. If you are author or own the copyright of this book, please report to us by using this report form. Report r6l17
Overview 4q3b3c
& View L293d Motor Driver Datasheet as PDF for free.
More details 26j3b
- Words: 3,266
- Pages: 14
L293, L293D QUADRUPLE HALF-H DRIVERS SLRS008B – SEPTEMBER 1986 – REVISED JUNE 2002
D D D D D D D D D D
Featuring Unitrode L293 and L293D Products Now From Texas Instruments Wide Supply-Voltage Range: 4.5 V to 36 V Separate Input-Logic Supply Internal ESD Protection Thermal Shutdown High-Noise-Immunity Inputs Functional Replacements for SGS L293 and SGS L293D Output Current 1 A Per Channel (600 mA for L293D) Peak Output Current 2 A Per Channel (1.2 A for L293D) Output Clamp Diodes for Inductive Transient Suppression (L293D)
N, NE PACKAGE (TOP VIEW)
1,2EN 1A 1Y HEAT SINK AND GROUND
16
2
15
3
14
4
13
5
12
2Y 2A
6
11
7
10
VCC2
8
9
VCC1 4A 4Y HEAT SINK AND GROUND 3Y 3A 3,4EN
DWP PACKAGE (TOP VIEW)
1,2EN 1A 1Y NC NC NC
description The L293 and L293D are quadruple high-current half-H drivers. The L293 is designed to provide bidirectional drive currents of up to 1 A at voltages from 4.5 V to 36 V. The L293D is designed to provide bidirectional drive currents of up to 600-mA at voltages from 4.5 V to 36 V. Both devices are designed to drive inductive loads such as relays, solenoids, dc and bipolar stepping motors, as well as other high-current/high-voltage loads in positive-supply applications.
1
HEAT SINK AND GROUND
1
28
2
27
3
26
4
25
5
24
6
23
7
22
8
21
9
20
NC NC 2Y 2A
10
19
11
18
12
17
13
16
VCC2
14
15
VCC1 4A 4Y NC NC NC HEAT SINK AND GROUND NC NC 3Y 3A 3,4EN
All inputs are TTL compatible. Each output is a complete totem-pole drive circuit, with a Darlington transistor sink and a pseudo-Darlington source. Drivers are enabled in pairs, with drivers 1 and 2 enabled by 1,2EN and drivers 3 and 4 enabled by 3,4EN. When an enable input is high, the associated drivers are enabled and their outputs are active and in phase with their inputs. When the enable input is low, those drivers are disabled and their outputs are off and in the high-impedance state. With the proper data inputs, each pair of drivers forms a full-H (or bridge) reversible drive suitable for solenoid or motor applications. On the L293, external high-speed output clamp diodes should be used for inductive transient suppression. A VCC1 terminal, separate from VCC2, is provided for the logic inputs to minimize device power dissipation. The L293and L293D are characterized for operation from 0°C to 70°C.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright 2002, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date. Products conform to specifications per the of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
L293, L293D QUADRUPLE HALF-H DRIVERS SLRS008B – SEPTEMBER 1986 – REVISED JUNE 2002
block diagram VCC1 1 0 1 0
1
16
2
15 1
M
14
4
13
5
12
6
11 3
7
10 9
8
VC NOTE: Output diodes are internal in L293D. TEXAS INSTRUMENTS AVAILABLE OPTIONS PACKAGE PLASTIC DIP (NE)
TA
L293NE L293DNE
0°C to 70°C
AVAILABLE OPTIONS PACKAGED DEVICES TA
0°C to 70°C
SMALL OUTLINE (DWP)
PLASTIC DIP (N)
L293DWP L293DDWP
L293N L293DN
The DWP package is available taped and reeled. Add the suffix TR to device type (e.g., L293DWPTR).
2
POST OFFICE BOX 655303
M
4
3
2 1 0
1 0
• DALLAS, TEXAS 75265
1 0 1 0
M
L293, L293D QUADRUPLE HALF-H DRIVERS SLRS008B – SEPTEMBER 1986 – REVISED JUNE 2002
FUNCTION TABLE (each driver) INPUTS† OUTPUT A
EN
Y
H
H
H
L
H
L
X
L
Z
H = high level, L = low level, X = irrelevant, Z = high impedance (off) † In the thermal shutdown mode, the output is in the high-impedance state, regardless of the input levels.
logic diagram 1A 1,2EN 2A
3A 3,4EN 4A
2 1 7
10 9 15
ÁÁ ÁÁ ÁÁ ÁÁ ÁÁ ÁÁ ÁÁ ÁÁ ÁÁ
3
6
11
14
1Y
2Y
3Y
4Y
schematics of inputs and outputs (L293) EQUIVALENT OF EACH INPUT
TYPICAL OF ALL OUTPUTS VCC2
VCC1 Current Source
Input
Output
GND
GND
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
L293, L293D QUADRUPLE HALF-H DRIVERS SLRS008B – SEPTEMBER 1986 – REVISED JUNE 2002
schematics of inputs and outputs (L293D) EQUIVALENT OF EACH INPUT
TYPICAL OF ALL OUTPUTS VCC2
VCC1 Current Source
Output
Input
GND GND
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage, VCC1 (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 V Output supply voltage, VCC2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 V Input voltage, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V Output voltage range, VO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –3 V to VCC2 + 3 V Peak output current, IO (nonrepetitive, t ≤ 5 ms): L293 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±2 A Peak output current, IO (nonrepetitive, t ≤ 100 µs): L293D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 1.2 A Continuous output current, IO: L293 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±1 A Continuous output current, IO: L293D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 600 mA Continuous total dissipation at (or below) 25°C free-air temperature (see Notes 2 and 3) . . . . . . . 2075 mW Continuous total dissipation at 80°C case temperature (see Note 3) . . . . . . . . . . . . . . . . . . . . . . . . . 5000 mW Maximum junction temperature, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. All voltage values are with respect to the network ground terminal. 2. For operation above 25°C free-air temperature, derate linearly at the rate of 16.6 mW/°C. 3. For operation above 25°C case temperature, derate linearly at the rate of 71.4 mW/°C. Due to variations in individual device electrical characteristics and thermal resistance, the built-in thermal overload protection may be activated at power levels slightly above or below the rated dissipation.
4
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
L293, L293D QUADRUPLE HALF-H DRIVERS SLRS008B – SEPTEMBER 1986 – REVISED JUNE 2002
recommended operating conditions
Supply voltage
VCC1 VCC2
VIH
High level input voltage High-level
VCC1 ≤ 7 V VCC1 ≥ 7 V
VIL
Low-level output voltage
MIN
MAX
4.5
7
VCC1 2.3
36
2.3 –0.3†
UNIT V
VCC1 7
V
1.5
V
V
TA Operating free-air temperature 0 70 °C † The algebraic convention, in which the least positive (most negative) designated minimum, is used in this data sheet for logic voltage levels.
electrical characteristics, VCC1 = 5 V, VCC2 = 24 V, TA = 25°C PARAMETER
TEST CONDITIONS
VOH
High-level output voltage
L293: IOH = –1 A L293D: IOH = – 0.6 A
VOL
Low-level output voltage
L293: IOL = 1 A L293D: IOL = 0.6 A
VOKH VOKL
High-level output clamp voltage
L293D: IOK = – 0.6 A
Low-level output clamp voltage
L293D: IOK = 0.6 A
IIH
High level input current High-level
IIL
Low level input current Low-level
ICC1
Logic supply current
A EN A EN
MIN
TYP
VCC2–1.8
VCC2–1.4 1.2
Output supply current
IO = 0
V V V
100
0.2
10
–3
–10
–2
–100
All outputs at high level
13
22
All outputs at low level
35
60
All outputs at high impedance ICC2
1.8
0.2
VI = 0
UNIT V
VCC2 + 1.3 1.3
VI = 7 V
IO = 0
MAX
8
24
All outputs at high level
14
24
All outputs at low level
2
6
All outputs at high impedance
2
4
µA µA
mA
mA
switching characteristics, VCC1 = 5 V, VCC2 = 24 V, TA = 25°C PARAMETER
TEST CONDITIONS
tPLH tPHL
Propagation delay time, low-to-high-level output from A input
tTLH tTHL
Transition time, low-to-high-level output
Propagation delay time, high-to-low-level output from A input
CL = 30 pF, pF
L293NE, L293DNE MIN
See Figure 1
Transition time, high-to-low-level output
TYP
MAX
UNIT
800
ns
400
ns
300
ns
300
ns
switching characteristics, VCC1 = 5 V, VCC2 = 24 V, TA = 25°C PARAMETER
TEST CONDITIONS
L293DWP, L293N L293DDWP, L293DN MIN
TYP
UNIT
MAX
tPLH tPHL
Propagation delay time, low-to-high-level output from A input
750
ns
Propagation delay time, high-to-low-level output from A input
200
ns
tTLH tTHL
Transition time, low-to-high-level output
100
ns
350
ns
CL = 30 pF, pF
See Figure 1
Transition time, high-to-low-level output
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
L293, L293D QUADRUPLE HALF-H DRIVERS SLRS008B – SEPTEMBER 1986 – REVISED JUNE 2002
PARAMETER MEASUREMENT INFORMATION tf
tr
Input
5 V 24 V
Input
50%
50% 10%
Pulse Generator (see Note B)
VCC1 VCC2
10%
0
tw
A
tPLH
tPHL Y
3V
EN
Output CL = 30 pF (see Note A)
90%
90% 50%
50% 10%
tTHL TEST CIRCUIT
VOLTAGE WAVEFORMS
NOTES: A. CL includes probe and jig capacitance. B. The pulse generator has the following characteristics: tr ≤ 10 ns, tf ≤ 10 ns, tw = 10 µs, PRR = 5 kHz, ZO = 50 Ω.
Figure 1. Test Circuit and Voltage Waveforms
POST OFFICE BOX 655303
VOH
Output 10%
6
3V
90%
90%
• DALLAS, TEXAS 75265
VOL tTLH
L293, L293D QUADRUPLE HALF-H DRIVERS SLRS008B – SEPTEMBER 1986 – REVISED JUNE 2002
APPLICATION INFORMATION 5V
24 V VCC2
VCC1 16
10 kΩ
3
1,2EN 1
Control A
1A
1Y
2
3
Motor 2A
2Y
7
6
3,4EN 9
Control B
3A
3Y
10
11
4A
4Y
15
14 Thermal Shutdown
4, 5, 12, 13 GND
Figure 2. Two-Phase Motor Driver (L293)
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
7
L293, L293D QUADRUPLE HALF-H DRIVERS SLRS008B – SEPTEMBER 1986 – REVISED JUNE 2002
APPLICATION INFORMATION 5V
24 V VCC1
10 kΩ
VCC2 3
16
1,2EN 1
Control A
1Y
1A 2
3
Motor 2A
2Y
7
6
3,4EN 9
Control B
3A 10
3Y
4A 15
4Y
11
14 Thermal Shutdown
4, 5, 12, 13 GND
Figure 3. Two-Phase Motor Driver (L293D)
8
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
L293, L293D QUADRUPLE HALF-H DRIVERS SLRS008B – SEPTEMBER 1986 – REVISED JUNE 2002
APPLICATION INFORMATION VCC2
SES5001 M1
SES5001 M2
3A 10
11
4A 15
EN
3A
H
H
Fast motor stop
H
Run
H
L
Run
L
Fast motor stop
X
Free-running motor stop
X
Free-running motor stop
14 16
8
VCC1
L 1/2 L293
9
EN
M1
4A
M2
L = low, H = high, X = don’t care
4, 5, 12, 13 GND
Figure 4. DC Motor Controls (connections to ground and to supply voltage) VCC2
2 × SES5001
M
2A
1A 7
6
3
1A
2A
H
L
H
Turn right
H
H
L
Turn left
EN
2 × SES5001 2 16 8 1/2 L293
1
VCC1
FUNCTION
H
L
L
Fast motor stop
H
H
H
Fast motor stop
L
X
X
Fast motor stop
EN L = low, H = high, X = don’t care
4, 5, 12, 13 GND
Figure 5. Bidirectional DC Motor Control
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
9
L293, L293D QUADRUPLE HALF-H DRIVERS SLRS008B – SEPTEMBER 1986 – REVISED JUNE 2002
APPLICATION INFORMATION IL1/IL2 = 300 mA
C1 0.22 µF
16
L293
1 2 D5
L1
VCC2
IL1
15 +
D1
+
D8
3
14
4
13
5
12
6
11 +
D6
VCC1
D4
L2
IL2
+
7
10
8
9
D7
D3
D2
D1–D8 = SES5001
Figure 6. Bipolar Stepping-Motor Control
mounting instructions The Rthj-amp of the L293 can be reduced by soldering the GND pins to a suitable copper area of the printed circuit board or to an external heatsink. Figure 9 shows the maximum package power PTOT and the θJA as a function of the side of two equal square copper areas having a thickness of 35 µm (see Figure 7). In addition, an external heat sink can be used (see Figure 8). During soldering, the pin temperature must not exceed 260°C, and the soldering time must not be longer than 12 seconds. The external heatsink or printed circuit copper area must be connected to electrical ground.
10
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
L293, L293D QUADRUPLE HALF-H DRIVERS SLRS008B – SEPTEMBER 1986 – REVISED JUNE 2002
APPLICATION INFORMATION Copper Area 35-µm Thickness
Printed Circuit Board
Figure 7. Example of Printed Circuit Board Copper Area (used as heat sink)
17.0 mm
11.9 mm
38.0 mm
Figure 8. External Heat Sink Mounting Example (θJA = 25°C/W)
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
11
L293, L293D QUADRUPLE HALF-H DRIVERS SLRS008B – SEPTEMBER 1986 – REVISED JUNE 2002
APPLICATION INFORMATION MAXIMUM POWER AND JUNCTION vs THERMAL RESISTANCE
MAXIMUM POWER DISSIPATION vs AMBIENT TEMPERATURE
4
80
2
60
40
PTOT (TA = 70°C)
1
20
0
0 0
10
30
20 Side
40
50
P TOT – Power Dissipation – W
θJA
3
θ JA – Thermal Resistance – °C/W
P TOT – Power Dissipation – W
5 With Infinite Heat Sink 4
3
Heat Sink With θJA = 25°C/W
2 Free Air 1
0 –50
50
100
TA – Ambient Temperature – °C
– mm
Figure 9
12
0
Figure 10
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
150
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should that such information is current and complete. All products are sold subject to TI’s and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third–party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265
Copyright 2002, Texas Instruments Incorporated
This datasheet has been from: www.datasheetcatalog.com Datasheets for electronics components.
D D D D D D D D D D
Featuring Unitrode L293 and L293D Products Now From Texas Instruments Wide Supply-Voltage Range: 4.5 V to 36 V Separate Input-Logic Supply Internal ESD Protection Thermal Shutdown High-Noise-Immunity Inputs Functional Replacements for SGS L293 and SGS L293D Output Current 1 A Per Channel (600 mA for L293D) Peak Output Current 2 A Per Channel (1.2 A for L293D) Output Clamp Diodes for Inductive Transient Suppression (L293D)
N, NE PACKAGE (TOP VIEW)
1,2EN 1A 1Y HEAT SINK AND GROUND
16
2
15
3
14
4
13
5
12
2Y 2A
6
11
7
10
VCC2
8
9
VCC1 4A 4Y HEAT SINK AND GROUND 3Y 3A 3,4EN
DWP PACKAGE (TOP VIEW)
1,2EN 1A 1Y NC NC NC
description The L293 and L293D are quadruple high-current half-H drivers. The L293 is designed to provide bidirectional drive currents of up to 1 A at voltages from 4.5 V to 36 V. The L293D is designed to provide bidirectional drive currents of up to 600-mA at voltages from 4.5 V to 36 V. Both devices are designed to drive inductive loads such as relays, solenoids, dc and bipolar stepping motors, as well as other high-current/high-voltage loads in positive-supply applications.
1
HEAT SINK AND GROUND
1
28
2
27
3
26
4
25
5
24
6
23
7
22
8
21
9
20
NC NC 2Y 2A
10
19
11
18
12
17
13
16
VCC2
14
15
VCC1 4A 4Y NC NC NC HEAT SINK AND GROUND NC NC 3Y 3A 3,4EN
All inputs are TTL compatible. Each output is a complete totem-pole drive circuit, with a Darlington transistor sink and a pseudo-Darlington source. Drivers are enabled in pairs, with drivers 1 and 2 enabled by 1,2EN and drivers 3 and 4 enabled by 3,4EN. When an enable input is high, the associated drivers are enabled and their outputs are active and in phase with their inputs. When the enable input is low, those drivers are disabled and their outputs are off and in the high-impedance state. With the proper data inputs, each pair of drivers forms a full-H (or bridge) reversible drive suitable for solenoid or motor applications. On the L293, external high-speed output clamp diodes should be used for inductive transient suppression. A VCC1 terminal, separate from VCC2, is provided for the logic inputs to minimize device power dissipation. The L293and L293D are characterized for operation from 0°C to 70°C.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright 2002, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date. Products conform to specifications per the of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
L293, L293D QUADRUPLE HALF-H DRIVERS SLRS008B – SEPTEMBER 1986 – REVISED JUNE 2002
block diagram VCC1 1 0 1 0
1
16
2
15 1
M
14
4
13
5
12
6
11 3
7
10 9
8
VC NOTE: Output diodes are internal in L293D. TEXAS INSTRUMENTS AVAILABLE OPTIONS PACKAGE PLASTIC DIP (NE)
TA
L293NE L293DNE
0°C to 70°C
AVAILABLE OPTIONS PACKAGED DEVICES TA
0°C to 70°C
SMALL OUTLINE (DWP)
PLASTIC DIP (N)
L293DWP L293DDWP
L293N L293DN
The DWP package is available taped and reeled. Add the suffix TR to device type (e.g., L293DWPTR).
2
POST OFFICE BOX 655303
M
4
3
2 1 0
1 0
• DALLAS, TEXAS 75265
1 0 1 0
M
L293, L293D QUADRUPLE HALF-H DRIVERS SLRS008B – SEPTEMBER 1986 – REVISED JUNE 2002
FUNCTION TABLE (each driver) INPUTS† OUTPUT A
EN
Y
H
H
H
L
H
L
X
L
Z
H = high level, L = low level, X = irrelevant, Z = high impedance (off) † In the thermal shutdown mode, the output is in the high-impedance state, regardless of the input levels.
logic diagram 1A 1,2EN 2A
3A 3,4EN 4A
2 1 7
10 9 15
ÁÁ ÁÁ ÁÁ ÁÁ ÁÁ ÁÁ ÁÁ ÁÁ ÁÁ
3
6
11
14
1Y
2Y
3Y
4Y
schematics of inputs and outputs (L293) EQUIVALENT OF EACH INPUT
TYPICAL OF ALL OUTPUTS VCC2
VCC1 Current Source
Input
Output
GND
GND
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
L293, L293D QUADRUPLE HALF-H DRIVERS SLRS008B – SEPTEMBER 1986 – REVISED JUNE 2002
schematics of inputs and outputs (L293D) EQUIVALENT OF EACH INPUT
TYPICAL OF ALL OUTPUTS VCC2
VCC1 Current Source
Output
Input
GND GND
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage, VCC1 (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 V Output supply voltage, VCC2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 V Input voltage, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V Output voltage range, VO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –3 V to VCC2 + 3 V Peak output current, IO (nonrepetitive, t ≤ 5 ms): L293 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±2 A Peak output current, IO (nonrepetitive, t ≤ 100 µs): L293D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 1.2 A Continuous output current, IO: L293 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±1 A Continuous output current, IO: L293D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 600 mA Continuous total dissipation at (or below) 25°C free-air temperature (see Notes 2 and 3) . . . . . . . 2075 mW Continuous total dissipation at 80°C case temperature (see Note 3) . . . . . . . . . . . . . . . . . . . . . . . . . 5000 mW Maximum junction temperature, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. All voltage values are with respect to the network ground terminal. 2. For operation above 25°C free-air temperature, derate linearly at the rate of 16.6 mW/°C. 3. For operation above 25°C case temperature, derate linearly at the rate of 71.4 mW/°C. Due to variations in individual device electrical characteristics and thermal resistance, the built-in thermal overload protection may be activated at power levels slightly above or below the rated dissipation.
4
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
L293, L293D QUADRUPLE HALF-H DRIVERS SLRS008B – SEPTEMBER 1986 – REVISED JUNE 2002
recommended operating conditions
Supply voltage
VCC1 VCC2
VIH
High level input voltage High-level
VCC1 ≤ 7 V VCC1 ≥ 7 V
VIL
Low-level output voltage
MIN
MAX
4.5
7
VCC1 2.3
36
2.3 –0.3†
UNIT V
VCC1 7
V
1.5
V
V
TA Operating free-air temperature 0 70 °C † The algebraic convention, in which the least positive (most negative) designated minimum, is used in this data sheet for logic voltage levels.
electrical characteristics, VCC1 = 5 V, VCC2 = 24 V, TA = 25°C PARAMETER
TEST CONDITIONS
VOH
High-level output voltage
L293: IOH = –1 A L293D: IOH = – 0.6 A
VOL
Low-level output voltage
L293: IOL = 1 A L293D: IOL = 0.6 A
VOKH VOKL
High-level output clamp voltage
L293D: IOK = – 0.6 A
Low-level output clamp voltage
L293D: IOK = 0.6 A
IIH
High level input current High-level
IIL
Low level input current Low-level
ICC1
Logic supply current
A EN A EN
MIN
TYP
VCC2–1.8
VCC2–1.4 1.2
Output supply current
IO = 0
V V V
100
0.2
10
–3
–10
–2
–100
All outputs at high level
13
22
All outputs at low level
35
60
All outputs at high impedance ICC2
1.8
0.2
VI = 0
UNIT V
VCC2 + 1.3 1.3
VI = 7 V
IO = 0
MAX
8
24
All outputs at high level
14
24
All outputs at low level
2
6
All outputs at high impedance
2
4
µA µA
mA
mA
switching characteristics, VCC1 = 5 V, VCC2 = 24 V, TA = 25°C PARAMETER
TEST CONDITIONS
tPLH tPHL
Propagation delay time, low-to-high-level output from A input
tTLH tTHL
Transition time, low-to-high-level output
Propagation delay time, high-to-low-level output from A input
CL = 30 pF, pF
L293NE, L293DNE MIN
See Figure 1
Transition time, high-to-low-level output
TYP
MAX
UNIT
800
ns
400
ns
300
ns
300
ns
switching characteristics, VCC1 = 5 V, VCC2 = 24 V, TA = 25°C PARAMETER
TEST CONDITIONS
L293DWP, L293N L293DDWP, L293DN MIN
TYP
UNIT
MAX
tPLH tPHL
Propagation delay time, low-to-high-level output from A input
750
ns
Propagation delay time, high-to-low-level output from A input
200
ns
tTLH tTHL
Transition time, low-to-high-level output
100
ns
350
ns
CL = 30 pF, pF
See Figure 1
Transition time, high-to-low-level output
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
L293, L293D QUADRUPLE HALF-H DRIVERS SLRS008B – SEPTEMBER 1986 – REVISED JUNE 2002
PARAMETER MEASUREMENT INFORMATION tf
tr
Input
5 V 24 V
Input
50%
50% 10%
Pulse Generator (see Note B)
VCC1 VCC2
10%
0
tw
A
tPLH
tPHL Y
3V
EN
Output CL = 30 pF (see Note A)
90%
90% 50%
50% 10%
tTHL TEST CIRCUIT
VOLTAGE WAVEFORMS
NOTES: A. CL includes probe and jig capacitance. B. The pulse generator has the following characteristics: tr ≤ 10 ns, tf ≤ 10 ns, tw = 10 µs, PRR = 5 kHz, ZO = 50 Ω.
Figure 1. Test Circuit and Voltage Waveforms
POST OFFICE BOX 655303
VOH
Output 10%
6
3V
90%
90%
• DALLAS, TEXAS 75265
VOL tTLH
L293, L293D QUADRUPLE HALF-H DRIVERS SLRS008B – SEPTEMBER 1986 – REVISED JUNE 2002
APPLICATION INFORMATION 5V
24 V VCC2
VCC1 16
10 kΩ
3
1,2EN 1
Control A
1A
1Y
2
3
Motor 2A
2Y
7
6
3,4EN 9
Control B
3A
3Y
10
11
4A
4Y
15
14 Thermal Shutdown
4, 5, 12, 13 GND
Figure 2. Two-Phase Motor Driver (L293)
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
7
L293, L293D QUADRUPLE HALF-H DRIVERS SLRS008B – SEPTEMBER 1986 – REVISED JUNE 2002
APPLICATION INFORMATION 5V
24 V VCC1
10 kΩ
VCC2 3
16
1,2EN 1
Control A
1Y
1A 2
3
Motor 2A
2Y
7
6
3,4EN 9
Control B
3A 10
3Y
4A 15
4Y
11
14 Thermal Shutdown
4, 5, 12, 13 GND
Figure 3. Two-Phase Motor Driver (L293D)
8
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
L293, L293D QUADRUPLE HALF-H DRIVERS SLRS008B – SEPTEMBER 1986 – REVISED JUNE 2002
APPLICATION INFORMATION VCC2
SES5001 M1
SES5001 M2
3A 10
11
4A 15
EN
3A
H
H
Fast motor stop
H
Run
H
L
Run
L
Fast motor stop
X
Free-running motor stop
X
Free-running motor stop
14 16
8
VCC1
L 1/2 L293
9
EN
M1
4A
M2
L = low, H = high, X = don’t care
4, 5, 12, 13 GND
Figure 4. DC Motor Controls (connections to ground and to supply voltage) VCC2
2 × SES5001
M
2A
1A 7
6
3
1A
2A
H
L
H
Turn right
H
H
L
Turn left
EN
2 × SES5001 2 16 8 1/2 L293
1
VCC1
FUNCTION
H
L
L
Fast motor stop
H
H
H
Fast motor stop
L
X
X
Fast motor stop
EN L = low, H = high, X = don’t care
4, 5, 12, 13 GND
Figure 5. Bidirectional DC Motor Control
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
9
L293, L293D QUADRUPLE HALF-H DRIVERS SLRS008B – SEPTEMBER 1986 – REVISED JUNE 2002
APPLICATION INFORMATION IL1/IL2 = 300 mA
C1 0.22 µF
16
L293
1 2 D5
L1
VCC2
IL1
15 +
D1
+
D8
3
14
4
13
5
12
6
11 +
D6
VCC1
D4
L2
IL2
+
7
10
8
9
D7
D3
D2
D1–D8 = SES5001
Figure 6. Bipolar Stepping-Motor Control
mounting instructions The Rthj-amp of the L293 can be reduced by soldering the GND pins to a suitable copper area of the printed circuit board or to an external heatsink. Figure 9 shows the maximum package power PTOT and the θJA as a function of the side of two equal square copper areas having a thickness of 35 µm (see Figure 7). In addition, an external heat sink can be used (see Figure 8). During soldering, the pin temperature must not exceed 260°C, and the soldering time must not be longer than 12 seconds. The external heatsink or printed circuit copper area must be connected to electrical ground.
10
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
L293, L293D QUADRUPLE HALF-H DRIVERS SLRS008B – SEPTEMBER 1986 – REVISED JUNE 2002
APPLICATION INFORMATION Copper Area 35-µm Thickness
Printed Circuit Board
Figure 7. Example of Printed Circuit Board Copper Area (used as heat sink)
17.0 mm
11.9 mm
38.0 mm
Figure 8. External Heat Sink Mounting Example (θJA = 25°C/W)
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
11
L293, L293D QUADRUPLE HALF-H DRIVERS SLRS008B – SEPTEMBER 1986 – REVISED JUNE 2002
APPLICATION INFORMATION MAXIMUM POWER AND JUNCTION vs THERMAL RESISTANCE
MAXIMUM POWER DISSIPATION vs AMBIENT TEMPERATURE
4
80
2
60
40
PTOT (TA = 70°C)
1
20
0
0 0
10
30
20 Side
40
50
P TOT – Power Dissipation – W
θJA
3
θ JA – Thermal Resistance – °C/W
P TOT – Power Dissipation – W
5 With Infinite Heat Sink 4
3
Heat Sink With θJA = 25°C/W
2 Free Air 1
0 –50
50
100
TA – Ambient Temperature – °C
– mm
Figure 9
12
0
Figure 10
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
150
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should that such information is current and complete. All products are sold subject to TI’s and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third–party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265
Copyright 2002, Texas Instruments Incorporated
This datasheet has been from: www.datasheetcatalog.com Datasheets for electronics components.
Related Documents 171j1w
L293d Motor Driver Datasheet 144228
October 2019 48
Driver De Motor A Pasos Con L293d 5w1s25
December 2019 27
Datasheet - M542h Stepper Motor Driver 6a4738
November 2019 50
L298 Dual H-bridge Motor Driver Datasheet 3p4u5o
November 2019 101
Amc7135 Led Driver Datasheet 4a201k
November 2019 56
Sla7024m(motor Driver) 6z6v6t
May 2021 0More Documents from "Ankit Daftery" 1i24q
L293d Motor Driver Datasheet 144228
October 2019 48
Psc Box Girder(prestressing) 82g46
May 2020 4
Data Structures Wikibooks 4u1d44
December 2019 92
Steel Tables By R Agor, Birla Publications.pdf 1740p
January 2022 0
Wsh Guidelines Improvingergonomicsintheworkplace 1g401h
December 2021 0