Glaunach Silencer Handbook 6l1r34

GLAUNACH Silencer Handbook I

NOISE

II

PRODUCTS

III

ACCESSORIES FOR SILENCERS

IV

CALCULATION

V

MATERIAL CODES & STANDARDS

VI

SURFACE TREATMENT

VII

INSTALLATION

VIII

INSULATION

IX

AVOIDANCE OF FAULTS

latest edition at www.glaunach.com

NOISE - Handbook I page 2 of 67

1. NOISE LEVEL “Sound Power Level" and "Sound Pressure Level" are two commonly confused characteristics of sound. Both have the same unit of measure (the Decibel) and the term "Sound Level". However, to understand how to measure and specify sound, we must first understand the difference between these properties: Sound Power Level (abbr.: Lw or SWL or PWL) is the acoustical energy emitted by the sound source, and is an absolute value. It is not affected by the environment. Think of it like a light bulb, which radiates light in every direction. If you could measure all the energy radiated by the bulb, then this would be the equivalent of sound power. Sound Power Level rustle of leaves mosquito buzzing normal conversation bird singing vacuum cleaner street traffic air compressor jack hammer hard rock music propeller plane taking off walkman (full volume) jet plane taking off shotgun rocket during lift off cannon shot love song of blue whales navy Sonar (at 3kHz)

dB 15 45 55 60 70 80 90 100 110 120 130 140 160 170 180 190 200

100 dB Sound Power Level !

100 dB Sound Power Level !

100 m

50 m

100 dB Sound Power Level © GLAUNACH GMBH

Edition 02.2007


Sound Pressure Level (abbr.: Lp or SPL) is a pressure disturbance in the atmosphere whose intensity is influenced not only by the strength of the source, but also by the surroundings and the distance from the source to the receiver. Sound pressure is what our ears hear and what sound meters measure. Let’s have a look to the light bulb again: Brightness is more than a matter of wattage. How far is the bulb from the observer? What colour is the room and how reflective is the wall surface? Is the bulb covered with a shade? If you take all of these factors affect of how much light reaches the receiver, this would be the equivalent of sound pressure. Sound Pressure Levels normal conversation highway Traffic diesel truck freight train jet plane taking off Auto horn pneumatic riveter jet take off artillery fire firework jet take off

52 dB Sound Pressure Level !

dB 60 70 90 100 110 120 130 140 150 160 180

@ feet 3 50 33 200 1000 3 3 100 500 3 1

@m 1 15 10 60 300 1 1 30 150 1 0.3

58 dB Sound Pressure Level !

100 m

50 m

100 dB Sound Power Level

rule of thumb each doubling of the distance = 6dB noise reduction

© GLAUNACH GMBH

Edition 02.2007


2. FREQUENCIES The frequency is a measure of how frequently a vibration repeats itself (oscillates) or the number of waves ing by in a second. A hertz is the unit of frequency – 1 oscillation per second; a kilohertz (kHz) is 1000 hertz – 1000 oscillations per second. Decibels with the sound pressure scale adjusted to conform with the frequency response of the human ear. A sound level meter that measures A-weighted decibels has an electrical circuit that allows the meter to have the same sensitivity to sound at different frequencies as the average human ear. There are also Bweighted and C-weighted scales, but the A-weighted scale is the one most commonly used for measuring loud noise.

The frequency range of human hearing is about 20 hertz to 20,000 hertz

Calculation of an A weighted octave band Frequency (Hz)

Measured Lp (dB)

A-Scale Correction (dB)

Corrected LpA (dB)

31.5

94

-39

55

63

95

-26

69

125

92

-16

76

250

95

-9

86

500

97

-3

94

1,000

97

0

97

2,000

102

+1

103

4,000

97

+1

98

8,000

92

-1

91

Note: The A-scale correction factors are fixed values.

The A-weighted sound level can now be calculated by combining the corrected band levels:

LPA = 10 log10 (Σ 10LpA/10)

here: LPA = 105,5 dB(A) © GLAUNACH GMBH

Edition 02.2007


Peak Frequency For the reduction of the noise intensity, knowledge of the peak frequency is important. Strouhal's calculation method provides a simple way to find this frequency:

f = s×

w d

s = Strouhal's number w = speed in m/s d = diameter in m However, the peak frequency is not exactly in the range of Strouhal's calculation. Other components are also important. Strouhal's formula shows only, that the peak frequency increases when the diameter decreases. Shifting the Peak Frequency Since it is easier to attenuate high frequencies than deep frequencies, we use a diff pipe to change peak frequencies. This shifts low frequencies to high frequencies and as a positive side effect, the noise level is reduced too.

Blow Off Pipe

63

© GLAUNACH GMBH

125

Diff Pipe

250 500

1K

2K

4K

8K

63

125

250

500

1K

2K

4K

8K

Edition 02.2007


3. VALVE NOISE There is no international standard for the calculation of valve noise. Glaunach uses several methods to estimate the unknown noise level of a valve. In most cases however, we can use values from our database, which we have developed from many tests on site. For a rough estimation of the unsilenced noise level, we recommend two formulas: VDI 2713* "Noise reduction in thermal power stations" specifies the following formula for the determination of the sound power level: LW0 = 17 log M + 50 log To - 15

According to this formula, only the quantity and the temperature are determining factors. More recent studies of exhaust valves have shown that the difference in pressure is the decisive factor for the sound's intensity. Both methods of calculation are indirectly related, since increases of quantity and temperature cause the pressure difference to rise. However, a comparison of different calculation methods shows that figures resulting from the "VDI*-Formula" are rather too high. API RP521** Lp30m = L + 10 log (0.5 MC²)

noise from valves can be expected to be in the region of 130 to 170 dB(A) Lw

* VDI = Verein Deutscher Ingenieure (German Association of Engineers) ** API = American Petroleum Institute © GLAUNACH GMBH

Edition 02.2007


4. NOISE REDUCTION In order to meet environmental demands, noise reduction requirements continue to increase. Design and construction of valves, silencers, and piping systems are therefore constantly improved. Traditional vent silencer designs require an absorption component to attenuate high frequency noise generated at the venting valve outlet. The expanded gas travels between baffles of straight or ring shape, where noise energy is reduced through viscous friction. Such a construction is cumbersome, as it requires very large silencers. This design necessitates the addition of an expansion chamber, installed upstream of the baffles, in which the turbulent flow can be calmed. How can we reduce valve noise efficiently? a. By transferring pressure drop from the valve to a silencer. Spring-loaded safety valves functioning automatically can be subjected to a back pressure amounting to 10 - 40 % of the set pressure. This means that part of the pressure difference can be absorbed in a controlled process within the silencer. b. By using diff pipes with small holes (< ∅ 8mm), so that the peak frequency is increased. Because high frequencies are easier to attenuate than lower ones. A very high noise reduction can be achieved through several concentrically arranged pressure stages. c.

By combining diff technology with traditional absorbing

technology. Through the arrangement of absorption material immediately after the pressure stages, developing whirls and the resulting noise are reduced and partially absorbed. What are the typical noise limits ? USA: API Medical Research Report EA 7301. (Ref 2) This document dates from 1973. It set a limit of 115 dB(A) to steady sound, and 140 dB (peak) to impulsive noise. These were based on the data in the US. OSHA 1970 Act. EU: 86/188/ECC. (Ref 4) … if a maximum value of the unweighted instantaneous sound pressure level is greater than 200 Pa (140 dB) "suitable and adequate" ear protectors must be used…

noise limits, for the avoidance of hearing damage should be in the range from 100 to 125 dB(A) Lw

© GLAUNACH GMBH

Edition 02.2007

PRODUCTS - Handbook II page 8 of 67

ABSORBING SILENCER type

A

application

- any vent or blow-down application - boiler start-up and purge - turbine by

media

gas, air, steam,

pressure drop

0 dB

noise reduction

25+ dB

design

circular baffles reduce the noise and allow thermal expansion of the construction. The absorber cover is totally made from stainless steel. The inlet nozzle is connected to a diff pipe that redirects the gas flow. The silencer can be extended with additional absorbers to achieve a higher noise reduction.

GLAUNACH GMBH

Edition 02.2007


DIFF SILENCER type

D

application


media

gas, air, steam,

pressure drop

> 0,2 bar / > 3 psi

noise reduction

up to 50 dB

design

several diff stages and a fine stainless steel wire mesh are the basic principle of diff silencers. This technology s a substantial smaller and lighter construction compared to absorbing silencers.

GLAUNACH GMBH

Edition 02.2007


DIFF SILENCER type

DA

application


media

gas, air, steam,

pressure drop

> 0,2 bar / > 3 psi

noise reduction

up to 50 dB

design

the type DA diff silencer is similar to type D, except that the silencer shell is equipped with an additional insulation. The insulation is needed for temperature and noise control.

GLAUNACH GMBH

Edition 02.2007


COMBINED SILENCER (DIFF + ABSORBER) type

DAA

application


media

gas, air, steam,

pressure drop

> 0,2 bar / > 3 psi

noise reduction

50+ dB

design

the type DAA diff silencer is a combination of type A and type DA silencer. With additional absorbers almost any noise reduction can be achieved.

GLAUNACH GMBH

Edition 02.2007


INLINE DIFF SILENCER type

INLINE

application

in particular for closed systems - any vent or blow-down application - condenser injection - turbine by

media

steam, gas, air,

pressure drop

> 0,2 bar / > 3 psi

noise reduction

up to 50 dB

design

for noise control at pipes, we manufacture the Inline Silencer. This type is similar to the Diff Silencer D. Many small diff holes disengage the fluid into a fine stainless steel wire mesh.

GLAUNACH GMBH

Edition 02.2007


DUMP TUBE application

- low pressure - condenser injection - turbine by - redirection of the gas flow - pressure control - temperature control

media

steam, gas, air,

pressure drop

> 0,2 bar / > 3 psi

noise reduction

up to 35 dB

design

carbon or stainless steel dump tubes are furnished with a customized number and size of diff holes.

GLAUNACH GMBH

Edition 02.2007


DIFF type

DIFF

application

- any vent or blow-down application - condenser injection - turbine by - redirection of the gas flow - pressure control - temperature control

media

steam, gas, air,

pressure drop

0 bar / 0 psi

noise reduction

up to 50 dB

design

diffs are used for same applications as dump tubes, but with a higher noise reduction. The fluid es through several diff stages and through a fine stainless steel wire mesh.

GLAUNACH GMBH

Edition 02.2007


COLLECTING PIPE type

COLLECTING PIPE

application

to connect more than two blow-off pipes into one silencer, we recommend to use a collecting tube. Valves with different set pressures can be combined. Therefore the down stream pressure of all valves needs to be equated.

media

steam, gas, air,

pressure drop

> 0,2 bar / > 3 psi

noise reduction

up to 15 dB (without silencer)

design

silencers equipped with collecting pipes are designed for the maximum possible flow level

80 psi

40 psi

80 psi 145 psi

GLAUNACH GMBH

Edition 02.2007


RENTAL SILENCER type

DA & DAA

application

- any vent or blow-down application - boiler start-up and purge - turbine by with the construction of new boilers, equipment change, or repair work, debris may be introduced into the piping system. This must be removed before the process gas or steam is used. These contaminants are removed by “blowing free“ the piping. Often silencers are used that do not withstand the continuous stress or which become ineffective as a result of obstructions in the diff. Glaunach has developed a special Silencer which can be used repeatedly. This silencer allows the replacement of a diff cartridge in the event its performance is impeded by debris and back pressure becomes too high.

media

steam, gas, air,

pressure drop

> 0,2 bar / > 3 psi

noise reduction

up to 70 dB

design

DA or DAA Diff Silencers, but with exchangeable diff cartridge

GLAUNACH GMBH

Edition 02.2007

ACCESSORIES - Handbook III page 17 of 67

LIFTING LUGS application

all products are equipped with lifting lugs

purpose

lifting lugs are furnished on all units for ease of handling

design

carbon or stainless steel typically from the same material as silencer shell

IDENTIFICATION PLATE application

all products are equipped with an identification plate

purpose

identification and design information

design

anodized aluminium or stainless steel (extra charge)

PRESSURE GAUGE application

on customers request

purpose

connection for instruments for pressure or temperature measuring at the silencer inlet nozzle.

design

GLAUNACH GMBH

carbon or stainless steel closed with a plug (½ inch whitworth thread)

Edition 02.2007


DEWATERING PIPE application

all products are equipped with a dewatering device

purpose

drainage for condensation and rainwater

design

carbon or stainless steel typically from the same material as the silencer shell

EAVE RING application

all kinds of vent silencers

purpose

drip mould for rain water and connecting point for external insulation

design

carbon or stainless steel typically from the same material as welded on

COLLAR SHEET application


purpose

In-roof installations, drip mould for rain water and connecting point of external insulation

design


GLAUNACH GMBH

Edition 02.2007


BRACKETS application

all kinds of products

purpose

design


LEGS application

all kinds of products

purpose

design

customized from carbon or stainless steel typically from the same material as welded on

RAIN CAP (WEATHER HOOD) application


purpose

protection for heavy rain or snow fall

design

typically from the same material as silencer shell according to the required noise level, the rain hood is equipped with an absorbing face

GLAUNACH GMBH

Edition 02.2007


GOOSE NECK application


purpose

redirection of the gas flow

design

customized from carbon or stainless steel typically from the same material as silencer shell

FLANGE application

inlet nozzles, outlet pipe, dewatering

design

plain flange or flange kit including nuts, bolts, gasket and 2nd flange according requested standard

OUTLET EXTENSION application


purpose

Extension of the silencer outlet

design

customized from carbon or stainless steel typically from the same material as silencer shell

GLAUNACH GMBH

Edition 02.2007


MULTIPLE INLETS application


purpose

combination of different inlet pipes into one silencer

design

for simultaneous flow

EXCHANGEABLE DIFF CARTRIDGE application

diff silencers

purpose

for mediums with impurities which may plug the diff an affect the back pressure

design

wrapped with a stainless steel wire mesh.

ABSORBER application

all kind of vent silencers

purpose

noise reduction by absorbing materials

design

circular baffle elements made by a perforated plate from stainless steel. The internals are heat resistant glass fabrics and noise absorbing materials.

GLAUNACH GMBH

Edition 02.2007


HEATING application

all kinds of silencers and diffs

purpose

- for zones with extremely low ambient temperatures - if no temperature is transferred to the silencer

design

a heating system of 200 W will be used for silencers with outside diameter of up to 2 m. the heating capacity should be increased to 400 watts for silencers of larger diameters. the heating cartridge consists of a stainless steel pipe and a connecting shell. The pipe penetrates into a block of steel, which is welded to the silencer bottom. The connecting shell, made of aluminum is affixed at the outer end of the heating cartridge's pipe. Inside there are connection clamps and a thermostat which switches the heating cartridge on and off. No additional control device is necessary, however, a control light in the control room is recommended. The complete heating unit is fixed on the silencer with one bolt and can easily be exchanged if necessary.

GLAUNACH GMBH

Edition 02.2007


EXPANSION TS application

all kind of silencers and diffs

purpose

for vertical and/or horizontal movement of the entrance pipe caused by thermal expansion.

design

-

pressurized expansion ts (stainless steel) non pressurized expansion ts (stainless steel) sliding brackets sliding diff

BIRD SCREEN application


purpose

prevent birds from nesting inside the silencer

design

stainless steel grating at the silencer outlet

GLAUNACH GMBH

Edition 02.2007


INSULATION CLIPS* application


purpose

thermal and acoustical wool insulation

design

spikes or clamps

* See also “Handbook VIII Insulation”

GLAUNACH GMBH

Edition 02.2007

CALCULATION - Handbook IV page 25 of 67

1. REDUCED NOISE LEVEL (Lr) The required noise level Lr must be specified by the customer. This level must be conforming to the local requirements, in conjunction with the requirements of the end . If you are unsure about these requirements we recommend to limit the Sound Power Level according to US OSHA: Personnel protection-OSHA 1910.95 When employees are subjected to sound exceeding those listed in the table below, feasible istrative or engineering controls shall be utilized. If such controls fail to reduce sound levels within the levels, personal protective equipment shall be provided and used to reduce sound levels within the levels of the table. If the variations in noise level involve maxima at intervals of 1 second or less, it is to be considered continuous. ____________ PERMISSIBLE NOISE EXPOSURES ____________ | Duration per day, hours | Sound level dB(A) slow response _____________________________ __________________________ | 8 | 90 6 | 92 4 | 95 3 | 97 2 | 100 1 1/2 | 102 1 | 105 1/2 | 110 1/4 or less | 115 ________________________________________________________ When the daily noise exposure is composed of two or more periods of noise exposure of different levels, their combined effect should be considered, rather than the individual effect of each. If the sum of the following fractions: C(1)/T(1) + C(2)/T(2) C(n)/T(n) exceeds unity, then, the mixed exposure should be considered to exceed the limit value. Cn indicates the total time of exposure at a specified noise level, and Tn indicates the total time of exposure permitted at that level. Exposure to impulsive or impact noise should not exceed 140 dB peak sound pressure level. More details at: http://www.osha.gov It is important to know that if several valves open at the same time, there is an additive effect to the overall noise level. © GLAUNACH GMBH

Edition 02.2007


2. ADJUSTMENTS DETERMINED BY DISTANCE Usually the sound level is evaluated from the silencer shell at a specific distance. To calculate adjustments determined by distance, following methods can be used:

Hemispherical Radiation The noise level from silencers (installed on a roof) radiates out hemispherical into the environment. The sound pressure level decreases according to the following formula:

∆Lr = 10 log (2 π r²) Example: 5m beside the silencer exit you have measured Lp5m = 90 dB a) Calculate the Sound Power Level Lw b) Calculate the Sound Pressure Level in a distance of 20m from the outlet Lp20m a) ∆Lr = 10 log (2 π (0.5+5)²) ∆Lr = 22,7 Lw = Lp5m + ∆Lr = 90 + 22,7 Lw = 112,7 dB

r

b) 0.5m

5m

Lp20m = Lw – 10 log (2 π r²) = 113,5 – 10 log (2 π (0.5+20²) Lp20m = 79,3 dB or

NOTE the distance from the silencer axis to the silencer shell must be considered in noise calculations

© GLAUNACH GMBH

Lp20m = Lp5m – 20 log (r2/r1) = 90 – 20 log (0.5+20)/(0.5+5) Lp20m = 78,6 dB

Edition 02.2007


3. TRANSMISSION FACTORS (∆ ∆L) The sound level adjustments determined by distance are only valid within 25 m from the noise source. If the evaluation level is at a distance greater than 25 meters, the following parameters should be considered: ∆La = air reflecting measure in dB ∆LΦ = direction correction in dB ∆Ls = screen measure in dB ∆Lv = vegetation attenuation measure in dB ∆Lrx = area reflecting measure in dB ∆Lb = bottom attenuation measure in dB

Most of these can only be identified by an acoustic engineer at site. For that reason we only have a look at ∆La and ∆LΦ:

∆La Air reflection measure Sound absorption in the air depends on the frequency, temperature, and humidity. The following chart represents approximate frequency adjustments for dB/m at 10°C and an air humidity of 70%.

f(Hz) dB / m

© GLAUNACH GMBH

125 0,001

250 0,001

500 0,002

1K 0,004

2K 0,008

4K 0,021

8K 0,052

Edition 02.2007


∆LΦ Φ Direction Correction

0°

45°

80° 90°

110°

Silencer

Roof

Vertical silencers direct the sound energy up. For vertical applications, depending upon the angle of reflection, the following increases apply:

Angle of reflection Φ Correction in dB

110° - 90 ° 0

90 ° - 80 ° 80 ° - 45 ° 1

3

0° 20

Φ= angle of reflection between silencer axis and evaluation point.

Because of the higher noise level at the silencer outlet, the silencer should always blow upward. Rain caps reflect the sound, even when they have an absorbing surface. Therefore, we recommend that rain caps should only be used if absolutely necessary. Under normal circumstances, the point of noise reduction is below the horizontal axis of the silencer outlet. For such points, no correction is necessary.

© GLAUNACH GMBH

Edition 02.2007


4. UNSILENCED SOUND POWER LEVEL OF VALVES The following two calculations can be used for a rough estimation of the unsilenced sound level of a valve.

VDI 2713 Lw0 = 17 log M + 50 log To - 15

Lw0: Sound Power Level of the valve in dB M: capacity in t/h (if M < 10 t/h then M = 10 t/h) T0: gas temperature at the valve in K This formula identifies the total Sound Power emitted by a source. The Sound Power is the acoustical energy emitted by the sound source, and is an absolute value. It is not affected by the environment or distance.

ANSI/API RP 521

Lp30m = L + 10 log (0.5 MC²)

Lp30m: Sound Pressure Level 30 meters (100 feet) from stack tip in dB L: noise intensity at 30 meters (100 feet) from stack tip dB M: capacity in in kg/s C: Speed of sound in the gas at he valve in m/s This formula identifies the total Sound Pressure emitted by a source. Sound Pressure is a pressure in the atmosphere whose intensity is influenced not only by the strength of the source, but also by the surroundings and the distance from the source to the receiver. Sound Pressure is what our ears hear and what sound meters measure.

© GLAUNACH GMBH

Edition 02.2007


Example: Calculate the Sound Power Level of a Safety Valve: Medium: H2O Steam Capacity: 100 t/h Upstream Temperature: 500 °C Upstream Pressure: 50 bar Downstream Pressure: 8 bar

VDI 2713 M = 100 t/h T0 = 500°C + 273,15 = 773.15 K Lw0 = 17 log (100) + 50 log (773.15) – 15 ≈ 163 dB

ANSI/API RP 521 PR = 50/8 ≈ 6 You have to refer to ANSI/API RP 521 (Guide for Pressure-Relieving and Depressuring Systems) to get the noise intensity from the L/PR diagram. L = 60 dB M = 100 t/h = 27.8 kg/s C =

664 m/s (from “properties of water and steam”)

Lp30m = 60 + 10 log (0.5 * 27.8 * 664²) = 128 dB ∆Lr = 10 log (2 π 30²) = 38 Lw0 = Lp30m

© GLAUNACH GMBH

+

∆Lr = 128 + 38 ≈ 166 dB

Edition 02.2007


5. DETERMINATION OF DYNAMIC INSERTION LOSS (DIL) in order to obtain a correct result for the calculation of the sound power level of silencers (LW), the required evaluation level (Lr) of the silencer needs several adjustments (∆lr ) and transmission factors ∆La, ∆Lrx, ∆Ls, ∆Lv, ∆Lb Lw

= Lr + ∆Lr - ∆LΦ + ∆La

The transmission factors . ∆Lrx, ∆Lrs, ∆Lrv, ∆Lrb.are not considered here as their calculations are very difficult.

DIL = Lw0 - Lw

Example 1: Valve capacity M = 100 t/h Temp. in front of the valve t0 = 500°C Pressure in front of the valve p0 = 100 bar The required evaluation level Lr is 85 dB(A) at a distance of 7 meters Calculate the necessary dynamic insertion loss (DIL) for a silencer:

7m

The noise source is rather close (<25m), a distance depending noise reduction can be made without corrections. Lw0 = 17 log 100 + 50 log (273 + 500) - 15 = 163,4 dB(A) ∆Lr = 10 log (2 π 7²) = 24,9 dB Lw = 85+24,9 = 110 dB(A) DIL = Lw0 - Lw = 163,4 - 110 = 53,4 dB

© GLAUNACH GMBH

Edition 02.2007


Example 2: Valve capacity M = 100 t/h Temp. in front of the valve t0 = 500°C Pressure in front of the valve p0 = 100 bar The required evaluation level Lr is 50 dB(A) at a distance of 300 meters on a hill, 50 meters above the steam outlet. The maximum noise level was measured at a frequency of 2000 Hz Calculate the necessary dynamic insertion loss (DIL) for a silencer:

Φ 300m

50m

Lw0 = 17 log 100 + 50 log (273 + 500) - 15 = 163,4 dB(A) ∆Lr = 10 log (2 π 300²)

= 57,5 dB

direction correction (see page 5) Φ = 80° ∆LΦ = 3 dB air reflection (see page 4) ∆La = 0,008 × 300 = 2,4 dB Lw = 50 + 57,5 - 3 + 2,4

=

106,9 dB(A)

DIL = Lw0 - Lw = 163,4 - 106,9

© GLAUNACH GMBH

=

56,5 dB

Edition 02.2007


6. THERMAL EXPANSION

α

Thermal expansion α in 10-6 m /m°C between 20° and ... 100 °C 200 °C 300 °C 400 °C 500 °C 11.1 12.1 12.9 13.5 13.9

600 °C 14.1

Example: A pipe-line made of carbon steel has a length of 12 m and is loaded with a max. operating temperature of 490 °C. A sliding diff shall be provided to allow thermal expansion. For the temperature range 20°C to 500°C

α is 13.9

∆l = l × α × t × 10-6

∆l = 12 × 13.9 × 490 × 10-6 = 0.0817 m An expansion t for vertical movement of 81.7 mm is required

7. REACTION FORCES Reaction force from the vertical blow-off are calculated as follows:

R = wa² x Sa / va

R = Reaction force in N Sa = Outlet surface in m² wa = Blow off velocity of the expanded gas in m/s va = Specific volume of the expanded gas in m³/kg

© GLAUNACH GMBH

Edition 02.2007


Example: The outlet of a steam silencer has an open area of 0,7854 m² The capacity of the silencer is 20 kg/s, the temperature of the steam at the silencer outlet is 300°C at atmospheric pressure. You will need a Steam Table to read out the specific volume (va) of steam at 300°C and atmospheric pressure Sa

= 0,7854m²

M = 20 kg/s refer to steam table: va(300°C) = 2,63887 m³/kg Qa = M * va(300°C) = 52,8 m³/s Wa = Qa / Sa = 67,2 m/s

R = w a² * Sa

/ va

= 1344 N

R

NOTE due to the restricted velocity inside of vent silencers, the reaction forces are rather low and can be neglected

© GLAUNACH GMBH

Edition 02.2007


8. WIND AND EARTHQUAKES GLAUNACH silencers are built so compact that the wind forces can be led off over the shell without any problems. The of GLAUNACH silencers, e.g. brackets or legs are designed to withstand any possible loads from wind or earthquakes. Nevertheless, the ing structure, which is not scope of supply, should be examined by a stress analyst.

9. BACKGROUND NOISES ISO/DIS 11820.2 - Acoustic-Measurements This standard specifies how silencers are to be measured in specific applications. This standard cannot be used as the sole guideline for noise measurements, as it only provides for the measurement of ducted silencers. In chapter 1.2-b) Blow-down silencers are expressly mentioned. Table „Corrections for background noise“ shows that the background sound pressure level alone must be more than 3 dB lower than the measured operating sound source during the test. During the control measurement at a silencer all ambient noise, noise reflection of the valve and piping, must be accordingly lower. Under ideal conditions, it is often required that silencers meet extremely low silenced levels, e.g. 85 dB(A) at 1 meter from the silencer opening. Actual site visits reveal that the blow-off pipe between silencer and roof or valve is not damped, or the valve is outside and radiated noise levels from these sources are often overlooked. According ISO/DIS 11820.2 the control measurement is invalid! In the standard for different installation conditions, recommendations for the arrangement of the measuring points are given. The standard requires that measuring points be arranged on the silencer axis in front of the blow-off outlet. With blow-off silencers, however, the medium flows out of the silencer outlet at high velocities and high temperatures. As a result, it is not recommended that microphones be arranged in the gas path at the silencer outlet. ∆LΦ Direction Correction. Generally one point of reference is arranged laterally, beside or under the silencer opening. If the customer requires a point of reference over the silencer opening, a direction correction is to be made.

© GLAUNACH GMBH

Edition 02.2007


SYMBOLS SYMBOL

UNIT °

Φ -6

10

DESCRIPTION angle of reflection

m /m°C

expansion factor

m/s

speed of sound

DIL

dB

dynamic insertion loss

f

Hz

frequency

L

dB

noise intensity – API RP 521

∆l

m

thermal expansion

∆LΦ

dB

direction correction

∆La

dB

air reflecting measure

∆Lb Lp

dB

bottom attenuation measure

dB

sound pressure level

Lr

dB

required evaluation level of the silencer

∆Lr

dB

noise level reduction by distance

∆Lrx

dB

area reflecting measure

∆Ls

dB

screen measure

∆Lv Lw

dB

vegetation attenuation measure

dB

sound power level

M

kg/s

p0

bar(g)

PR

-

Qa

m³/s

r

m

distance

R

N

reaction force

Sa

m²

free area at silencer outlet

t0

°C

temperature upstream of valve

T0

K

temperature upstream of valve

va

m³/kg

wa

m/s

α C

© GLAUNACH GMBH

capacity (mass-flow of moving fluid) pressure upstream of valve pressure ratio quantity (volume-flow of moving fluid)

specific volume velocity (speed of moving fluid)

Edition 02.2007

MATERIALS, CODES & STANDARDS - Handbook V page 37 of 67

NOTE Materials used in the construction of silencers follow European standards and are stated on the following pages. In some cases, we will substitute higher grade materials in place of lower grade materials. Upon request, ASTM-materials and others can be used. Since blow-off silencers are normally loaded for short durations of time, maximum actual working time is based on 10,000 hrs.

1. SILENCER MATERIALS 1 2 3 4 5 6 7 8 9 10

Item No.

Part up to 400°C

Material up to 510°C

up to 540 °C

1

Jacket sheet

FE360B

P265GH

16Mo3

2

Perforated plate

1.4301

1.4301

1.4541

3

Absorption material

4

Diff plate

5

Perforated plate

6

Mineral wool and long strand glass lining P265GH

16Mo3

16Mo3

P265GH, 16Mo3

16Mo3

16Mo3

Diff tube

St35.8 I

16Mo3

16Mo3

7

Diff material

1.4301

1.4301

1.4541

8

Dewatering pipe

St35.8 I

St35.8 I

St35.8 I

9

Entrance pipe

St35.8 I

16Mo3

13CrMo4-5

10

Flange

C 22

16Mo3

13CrMo4-5

© GLAUNACH GMBH 2005

Edition 06.2005


2. MATERIAL ANALYSIS DIN

Chemical composition

Mat. No.

No.

Symbol

%C

%Si

%Mn

%P

%S

%Mo

%Cr

%Ni

%Ti

DIN EN 10025

1.0037

FE360B

≤0,17

-

-

≤ 0,045

≤ 0,045

-

-

-

-

DIN EN 10028 T2

1.0425

P265GH

≤ 0,20

≤ 0,40

0,50 - 1,40

≤ 0,030

≤0,025

≤0,08

≤0,30

-

-

DIN EN 10028 T2

1.5415

16Mo3

0,12 0,20

≤0,35

0,40 - 0,90

≤0,030

≤0,025

0,25 - 0,35

≤0,30

-

-

DIN EN 10028 T2

1.7335

13CrMo45

0,08 0,18

≤0,35

0,40 - 1,00

≤0,030

≤0,025

0,40 - 0,60

0,70 -1,15

-

-

DIN 17175

1.0305

St35.8 I

≤0,17

≤0,35

0,40

≤0,05

≤0,05

-

-

-

-

DIN 17441

1.4301

X5CrNi 1810

≤0,07

≤1,0

≤2,0

≤0,045

≤0,03

-

17,0-19,0

8,5-10,5

-

DIN 17441

1.4541

X6CrNiTi 1810

≤0,08

≤1,0

≤2,0

≤0,045

≤0,03

-

17,0-19,0

9,0-12,0

≥5x%C≤ 0,8

3. TENSILE TEST Material

Yield stress

Proof stress

Tensile strength

Elongation

Symbol

N/mm2

0,2 %

1%

N/mm2

%

P265GH

≥255

130 (400°C)

-

410-530

≥23

16Mo3

≥275

140 (500°C)

-

440-590

≥24

13CrMo4-5

≥300

165(500°C)

-

440-590

≥19

St35.8 I

≥240

-

-

350-450

≥25

1.4301

-

195

230

500-700

≥40

1.4541

-

200

235

500-730

≥35

4. LOWER LIMITING VALUE - CREEP RUPTURE STRENGTH DEPENDENT ON THE TEMPERATURE ACCORDING TO DIN EN 10028 T2 (DIN 17175) Material

380

390

400

410

420

430

440

450

460

470

480

490

500

510

520

530

540

550

560

570

P265GH, (St35.8 I) 10000 h

N/mm²

183

169

153

139

126

114

102

90,4

80

68,8

60

100000 h

N/mm²

132

118

106

94,4

82,4

72,8

63,2

55,2

47,2

40

33,6

16Mo3 10000 h

N/mm²

238

218

198

178

157

137

118

100

81,,6

100000 h

N/mm²

196

167

139

114

93,6

74,4

59,2

47,2

37,6

13CrMo4-5 10000 h

N/mm²

296

278

262

243

218

191

167

143

123

103

87

73

61

100000 h

N/mm²

228

201

176

152

130

110

92,8

75,2

62,4

48,4

39

32

26

tension applied to the original cross section which leads to rupture after 10000 or 100000 hrs. © GLAUNACH GMBH 2005

Edition 06.2005


5. COMPARISON OF INTERNATIONAL STANDARDS W-Nr. DIN 1.0425

P265GH

AFNOR A 42 ; AP

Great Britain B.S. 1501 Gr. 161-400; 151-400 1501 Gr. 164-360; 161-400 1501 Gr. 164-400; 154-400

Italy UNI

Sweden SS

USA AISI/SAE/ASTM

Fe4101KW;KG;KT Fe 410 2 KW; KG

1430 1432

A 516 Gr. 60 1)

1.5415

16 Mo 3

15 D 3

---

16 Mo 3 (KG; KW)

2912

A 204 Gr. A 4017

1.7335

13 CrMo 4-5

15 CD 3.5 15 CD 4.5

620-440 620-470 620-540 1501-620; 621

14 CrMo 3 16 CrMo 3

2216

A 182-F11; F12 A 387 Gr. 12 Cl.2

1.0305 1)

St 35.8 I

---

---

C14

---

A106Gr.A

C 22

AF 42 C 20 XC 25 1 C 22

C 20 C 21 C 25

1450

(M) 1020 M 1023

1.4301

X 5 CrNi 18 10

Z 4 CN 19-10 FF Z 5 CN 17-08 Z 6 CN 18-09 Z 7 CN 18-09

X 5 CrNi 18 10

2332 2333

304 304 H

1.4541

X 6 CrNiTi 18 10

Z 6 CNT 18-10

055 M 15 070 M 20 1449 22 HS, CS 304 S 15 304 S 16 304 S 17 304 S 18 304 S 25 304 S 31 321 S 18 321 S 22 321 S 31 321 S 51 (490; 510) 321 S 59 LWCF 24

X 6 CrNiTi 18 11

2337

321

1.0402

Source: Key to Steel, 16th Edition (1992) / P265GH included as H II; 16Mo3 as 15Mo3; 13CrMo4-5 as 13CrMo44 1) not included in the international comparison of norms of the Key to Steel.

6. QUALIFICATIONS We are qualified to manufacture silencers according to PED or ASME


Edition 06.2005


7. APPLICABLE CODES FOR VENT SILENCERS EU Certified Quality Assurance ISO 9001 : 2000, EN 729-2 Code / Guidline PED 97/23/EC Harmonized Standards AD-2000, TRD, EN 13480

US ISO 9001 : 2000 ASME Section VIII Div.1; B31.1 NBEP NA

Welder Performance Qualific. EN 287-1/ A1

ASME Section IX

Welding Procedure Specification EN 288-3 / A1

ASME Section IX

Approval of welding procedures ÖNORM 7812, AD2000-HP0, TRD 201 Marking PED 97/23/EC Kat I,II,III Inlet Pipe Matetrials EN, DIN Non Destructive Testing ISO-EN 473 VT, PT, RT, MT, UT Sandblasting ISO 12944/4- SA 2½


NA NA ASTM, ASME ASNT SNT-TC-1A-VT, PT, RT, MT, UT SSPC-SP 10

Edition 06.2005


8. QUALITY CONTROL Quality Assurance covering construction and production of ventsilencers follows standards and rules of (ISO, TRD, TRB, AD-instructional pamphlets) or purchaser's own specified quality assurance procedures and quality assurance system. Quality of Materials: The quality of the materials for pressure leading parts is determined by Inspection Certificates according. to DIN 50049 (DIN EN 10204): •

3.1A

for pre material 16Mo3, 13CrMo4-5

•

3.1B

for pre material P265GH, St35.8 I or ASTM materials

•

2.2 for all other materials

Quality check of the welded ts: Our company furnishes proof that conditions according to AD-brochure HP 0 are fulfilled. Conditions related to appropriate production according to the general principles for materials are given. We have appropriate: • • • •

production and welding equipment, welding personnel and welding supervision personnel, testing facilities, test personnel and test supervision personnel.

If necessary, welding qualification can be supplied in accordance with ASME SEC.IX. If a “Code“ stamp according to ASME is prescribed, the inspection is made by the “Authorized Inspection Agency“ Quality Management: GLAUNACH’s Quality Management System is in accordance with ISO 9001. Our Quality System was first certified in 1993 by Lloyd’s and continues to be constantly supervised and recertified annually.


Edition 06.2005



Edition 06.2005

SURFACE TREATMENT - Handbook VI page 43 of 67

GENERAL INFORMATION Attention to details while applying corrosion protection extends the service life of silencers substantially. For parts, that are particularly corrosion endangered, (e.g. thin perforated plates and flowed through absorbing materials), stainless steel is used. All carbon steels are sand-blasted and get a heat resistant protective coating. The flow-loaded internals are covered with a single and the exterior surface with a double primer. During transport and assembling the coating might be damaged. Therefore a repairing kit is supplied with Glaunach silencers. The repair kit includes a can of original painting and a roll-brush. You’ll find the repair kit at the silencer inlet. The internals of the inlet pipe and the diff don’t get a coating, since it would not survive the first blow-out. For transport the silencer inlets are closed with a plastic cap.

GLAUNACH GMBH

Edition 02.2007


1. SURFACE TREATMENT FOR CARBON STEEL According to standard for the silencers the following surface treatment is provided:

Silencer Inlet Pipe and Diff - Hand tool cleaning - slightly coated with oil

Silencer Shell Internals - Blast clean by compressed air with cast iron grit - Surface preparation grade SA2 1/2 according to DIN 55928T4 - Single coating with ethyl silicate zinc rich primer

Silencer Shell Exterior < 400°C (750°F) temperature load - Blast clean by compressed air with cast iron grit - Surface preparation grade SA 2½ according to DIN 55928T4 - Double coating with ethyl silicate zinc rich primer At a temperature load of approximately 450°C (840°F), this coating loses its corrosion resistance since the zinc particles melt. Nevertheless, pure aluminium silicon coatings with a temperature resistance of more than 500°C (932°F) offer less corrosion protection, since the mechanical resistance is very poor. Even without temperature load, pure aluminium silicon coatings may not prevent corrosion. Silencer Shell Exterior > 400°C (750°F) temperature load - Blast clean by compressed air with cast iron grit - Surface preparation grade SA3 according to DIN 55928T4 - Coating with aluminium in an electric arc spraying process - Sealer with aluminium silicon paint.

GLAUNACH GMBH

Edition 02.2007


2. SURFACE TREATMENT FOR STAINLESS STEEL Degreasing Grease, oil, cutting fluids, drawing compounds and other lubricants must be removed from the surface of stainless steel components before heat treatment (to prevent carbon pick-up) or final ivating treatments (to enable full access by the treatment). Parts must also be degreased prior to further assembly by welding, again to prevent pick-up of carbon at high temperature. Problems associated with chemical cleaning processes can be avoided by using mechanical cleaning. With all mechanical cleaning processes great care must be taken to prevent the stainless steel surface from becoming contaminated by iron, steel or iron oxide particles. Wire Brushing Wire brushing is useful to remove light heat tint, but again brushes must be of stainless steel, and these must never be used on materials other than stainless steels. Pickling and ivation Pickling is an acid treatment to remove high temperature scale produced in welding, heat treatment or hot working. It also removes red rust from corrosion of the steel or from corrosion of contaminant iron or steel particles. Note that ivation is not sufficiently aggressive to remove this corrosion product after the free iron has begun to rust. High temperature dark scale is not only undesirable for aesthetic reasons - it also results in a reduced corrosion resistance of the underlying steel surface layer.

GLAUNACH GMBH

Edition 02.2007


3. SAMPLES Sandblasting

Iron Grit Blasting: SA 2 ½ Blasting: SA 3

Iron Grit

Colours

Ethyl Silicate Zinc Carboline 11

GLAUNACH GMBH

Aluminium Coat Thermaline 4700

Edition 02.2007

INSTALLATION - Handbook VII page 47 of 67

1. INSTALLATION OF VENT SILENCERS

-

Vent Silencers should be installed as high as possible.

-

The inlet pipe downstream of the silencer, should be sized sufficiently to keep gas velocities low.

-

Bends should be avoided since they generate turbulences and flow noise.

-

Some back pressure at the silencer inlet should be allowed.

RULE OF THUMB higher inlet pressure = smaller and cheaper construction

Glaunach Vent Silencers are of such a light and compact construction, that in some cases the silencer is carried by the blow-off pipe without any other .

GLAUNACH GMBH

Edition 02.2007


2. ING STRUCTURE UNDER THE ROOF

The silencer is mounted at the blow-off pipe which is ed under the roof. In case of elongations due to temperature, the silencer moves upwards. The only precaution to be taken is the fitting of a suitable seal at the roof's age. Wall thickness of the blow-off pipe must be thick enough to withstand wind forces.

3. ING STRUCTURE IN THE ROOF Fixation of the silencer by brackets which are bolted to girders.

GLAUNACH GMBH

Edition 02.2007


4. ING STRUCTURE ON THE ROOF The silencer is mounted on brackets which are fixed on the roof. The blow-off pipe must be allowed to move sufficiently downwards or upwards, otherwise a compensator should be provided. If requested the diff of the silencer can be arranged “sliding” in the silencer shell. With this construction, the addition of an impact sound separation between diff and silencer is supplied.

5. FLEXIBLE INSTALLATION OF THE SILENCER The silencer can be mounted on balancing bearings to aide in the expansion process. In this case residual powers are permanently exerted on the pipe nozzles.

GLAUNACH GMBH

Edition 02.2007


6. DEWATERING In each diff silencer, rain water and must be drained by an unpressurized dewatering pipe at the bottom of the silencer. During starting up of the silencer, condensation of steam in the silencer is possible and hot water can come out. In such cases, especially in cold climatic zones, we recommend that the dewatering pipe is arranged close to the insulation. This will prevent the drain from freezing.

Please note that hot water may flow to the roof. For this reason, we recommend to arrange a plate beneath the dewatering pipe to avoid damages of the roof. Dewatering of rain-water through the diff inlet into the blow-off pipe or by a by- has to be avoided for the following reasons: •

Pollution caused by sand, dust, birds, etc., may penetrate into the pressurized pipe system and could plug the system.

•

Due to the back pressure in front the diff, steam will escape through the drain and considerably impair the effectiveness of the silencer.

GLAUNACH GMBH

Edition 02.2007


7. STORAGE If the silencers are stored outdoors, the inlet pipe and dewatering pipe must be directed upwards, to prevent rainwater from entering the silencer. Plastic covers are used to close the entrance and dewatering pipe. For long-term storage, the silencers must be placed under a roof.

8. FIRST BLOW OFF Before the first blowing off process, please remove all covers and shipping brackets. Before start-up, the blow off pipes should be cleaned without a silencer. Impurities such as ferric-oxide and organic materials may block the silencer. Silencers should not be installed close to facades, as the jet of steam could cause damage. Furthermore, sound reflection off walls can intensify the level of sound by about 10 dB

9. SLIDING DIFF On delivery of the silencer with sliding diff, the sliding diff is fixed with 3 bolts in the required position. After installation, the bolts must be removed. After the first blow off process we recommend to adjust the tension of the stuffing box, so tightness is guaranteed. If insulation above the stuffing box is provided, tension should be made and lock washers should installed.

10. SPARE PARTS Spare parts are not needed for a two-year operation or longer unless the silencer is provided with a heating element.

NOTE Please also refer to the installation manual which is part of any project documentation.

GLAUNACH GMBH

Edition 02.2007

INSULATION - Handbook VIII page 52 of 67

1. NOISE REFLECTION OF BLOW-OFF PIPES The blow-off silencer reduces the sound power level of a valve. Each valve and associated discharge piping radiates noise, which is not attenuated by the silencer. In VDMA* 24.422, regulations for the calculation of the noise reflection of relieving valves are mentioned. In VDI** 3733, calculation methods for the calculation of noise reflection of blow-off pipes is discussed. By means of these regulations we provide in the following a simplified table, where the noise reflection of a blow-off pipe can be determined. DN

“

4bar

9bar

14bar

19bar

24bar

29bar

40

1 1/2“

56

53

52

50

49

48

50

2“

54

51

50

48

47

47

1

65

2 /2“

52

49

48

46

45

45

80

3“

51

48

46

45

44

43

100

4“

49

46

45

43

42

42

150

6“

46

43

41

40

39

38

200

8“

45

42

40

39

38

37

250

10“

45

42

40

39

38

37

300

12“

45

42

40

38

36

37

350

14“

44

41

40

38

37

37

400

16“

44

41

39

37

36

36

450

18“

44

41

39

38

37

36

500

20“

44

41

39

38

37

36

600

24“

43

40

38

37

36

35

700

28“

42

39

37

36

35

34

800

32“

41

38

36

35

34

33

With formula 1a and 1b (see Handbook I) the inside sound power level of a valve can be calculated. According to this formula, only the steam quantity and the steam temperature is decisive for the intensity of the inside sound power level LW0. For the calculation of the attenuation of the blow-off pipe behind the valve, the following parameters are important. • • • • •

inside diameter of the pipe wall thickness of the pipe length of the transmission area pressure inside the pipe density

There are two methods of insulation: Acoustic Insulation & Thermic Insulation

*

VDMA = Verein Deutscher Maschinenbau-Anstalten

GLAUNACH GMBH

**

VDI = Verein Deutscher Ingenieure

Edition 02.2007


With the parameters from Tab.1 the noise reduction can be determined. Practically an approximate value with an exactness of ± 2dB is enough. With the following table, the noise pressure level of an 11 meter long blow-off pipe, in 1 meter distance from the uninsulated blow-off pipe, can be determined (Fig.1). The precondition of this example is that the valve and the total blow-off pipe is situated inside of a boiler house. If the valve and the blow-off pipe are located outside the noise reduction Di reduces for 10 dB (Fig.2). closed boiler house house

open

100° 1m LP 1

boiler

100° Lr 1m

Lr

1m 1m

11m

10m

Lwv

Lwv

Fig. 1 Fig.2

GLAUNACH GMBH

Edition 02.2007


Example: • • • •

valve capacity 50 t/h temperature in front of the valve 500°C pressure in front of the valve100 bar issible sound pressure level of the silencer in 1m distance is 96 dB(A)

according to formula from Handbook “Noise” : LW0 = 17 log 50 + 50 log (273 + 500) - 15 = 158.3 dB(A) • •

pressure in the blow-off pipe 9 bar blow-off pipe DN 300 / 12” noise reduction according Tab. 1 Di ≈ 42 dB

Sound pressure level 1m beside the blowoff pipe: LP1 = LW0 - Di = 158.3 - 42 = 116.3 dB(A) Beside the uninsulated blow-off pipe, the sound pressure level is about 20.3 dB higher than at the silencer outlet.

The uninsulated blow-off pipe beneath the silencer requires acoustic insulation, to meet the noise requirement !

GLAUNACH GMBH

Edition 02.2007


2. INSULATION OF BLOWOFF PIPES Figure 3 shows, a recommendation, as to how noise reduction of 20 to 30 dB can be obtained. In most of the cases, both the silencers and blow-off pipe are influenced by temperatures. The insulation must be selected and installed such that it can withstand thermal growth and environmental changes. The strength of the insulation should depend on the pipe diameter. A total thickness of 100-120 mm is sufficient, thicker layers may not improve the noise reduction. Our quotes will indicate whether the silencer must be insulated or not. Our silencer design will determine if the insulation must extend from the eave ring or the collar sheet (see Handbook III) down to the roof or blow off pipe penetration. The plate thickness of the silencer body is usually 5 mm. If the silencer must be installed in a climatic zone where danger of freezing exists, the dewatering pipe should be made to protrude only a few centimetres out of the insulation, or it should be connected to the boiler house. The blow-off pipe represents a temperature bridge. The temperature of the boiler house will be transmitted to the diff over the blow-off pipe. A long and non-insulated dewatering pipe is especially endangered to freeze !

Insulation between eave ring and the roof Design for the insulation of a silencer with under roof.

Fig.3

GLAUNACH GMBH

Edition 02.2007


Insulation between the collar sheet and the roof Design for the insulation of a silencer with very high noise reduction and over roof.

Fig.4

Design for the insulation of a silencer with very high noise reduction and in the roof.

Fig.5

GLAUNACH GMBH

Edition 02.2007


3. RECOMMENDATIONS FOR ACOUSTIC INSULATION The area of the blow-off pipe between the age through the roof and the bottom of the silencer - eave ring or collar sheet - should get absorbing sound insulation. This will prevent radiated noise emissions from the blow-off pipe and will prevent rainwater from entering the building through the roof opening Description of the construction A combined steel aluminium covering is used for the construction. This cover is to be constructed such that it does not come in with the steel aluminum connections. At these points suitable protective agents are to be used. Materials and materials quality Spacer, resp. ing structure These must be made of material St37.2 or equivalent. The sub-construction consists of spacer rings made of hoop steel 30 x 3 mm, with springy spacers which can take up all the thermal expansion of the ducts.The spacer rings must be fixed at a maximum distance of 940mm or 37”in an axial direction. Insulating materials The only material allowed are mineral wool mats with a minimum specific weight of 100 kgs/m³, with one side quilted on galvanized wire mesh. The area between pipe and outside insulation should not be filled-in except in case a mat insulation is not feasible. Mineral wool mats which have suffered a change of thickness because of moisture or of mechanical influences must be excluded. These mineral wool mats must be able to withstand long storage periods without change of their quality. The mineral wool mats must be cut to size and be fixed firmly around the pipe. The fixation of the mats is made with wire pins (at least 4 pieces /m²) and clips. The wire pins are welded on the blowoff pipe. Minimum thickness of the mineral wool 2 x 60 mm. External lining Seawater resistant aluminium sheet accord. to DIN1745 must be used for the external lining of thermal insulation and the combined thermal-sound insulation. Al Mg 3 Al Mg Mn Al Mg Mn

F 23, half hard F 23, half hard F 23, half hard

DIN1725Bl.1,W.Nr.3.3535 DIN1725/Bl.1,W.Nr.3.3527 DIN1725/Bl.1,W.Nr.3.3528

For the acoustic insulation galvanized steel plate is to be used as an intermediate layer. The steel plate must be deadened. The sound absorbing material may not consist of bitumen mass, since a temperature load is present. At the piping, each second seam is to be made as a stretch seam in order to ensure the stretch ability. The aluminium sheet of the external lining must be overlapped as shown in The external lining must be absolutely secured against slipping.

GLAUNACH GMBH

Edition 02.2007


Sheet metal screws thread-forming screws DIN 7513, material no. 1.4300 (V2A) and cylindrical sheet metal screws B oder BZ DIN 7971, material no. 1.4300 (V2A). protection As protection strips from KlingeritTM or a glass fabrics are to be used. rigid spacer ring In distances from max. 940mm

Screw connection M8x40 Flat steel welded on here

40 x 4 rivet

40 x 4

5

Klingerit-intermediate layer*)

rigid spacer ring made of hoop-steel 30x3

GLAUNACH GMBH

Edition 02.2007


Silencer

Eav es (firmly welden to ring, the bottom of the s ilencer)

Intermediate lay er for separation of Impact sound and thermal ins ulation min. Thicknes s 5 mm of material glas s fabric*) Klingerit or Fixingclamps required for more than OD 200 In cas e of temperatures over 200°C mmmmmmmmmmmmmmmmm S-Clamps shaped are to be us ed in order to stop the ex compens atetension. Distance from clamp to clamp 300 - 400 mm Mineral wool mats with s pecific weight Of min. 100 kg/m³, quilted on galvaniz ed wire mesh a min. 2 x 60 mm s pace ring Ex pansion s eam with permanent-elas tic s eal W ire nail with clips for fixing mineral wool min. 4 pcs . per m² the

Aluminium Rock wool mat plate Sound absorbing material* *) s teel Galv anized Rock wool plate* *) mat Entrace pipe

GLAUNACH GMBH

Edition 02.2007

AVOIDANCE OF FAULTS - Handbook IX page 60 of 67

In order to reach a satisfactory function and attenuation of the silencer, attention should be paid to some aspects which, if neglected, could cause malfunctions.

1. INSTALLATION OF VENT SILENCERS It does not make sense to determine the dimension of the blow-off pipe according to that of the valve outlet and then increase it shortly in front of the silencer. The high blow-off speed leads to pressure losses in the blow-off pipe and to an increase in sound emission from the pipe.

proper insulation of the blow-off pipe

the blow-off pipe is not insulated and too small

If the flow rate in the blow-off pipe is kept low and the permissible pressure loss in the silencer is diminished, then it comes to a more economical and acoustical efficient solution.

© GLAUNACH GMBH

Edition 02.2007


Unfortunately it happens quite often that very high noise reductions are required, but uninsulated pipes or valves are arranged nearby the silencer. In such a case, the noise level will be determined by the blow-off pipe or the valve, and not by the silencer.

130 dB 90 dB

the noise level emitted by the blow-off pipes is higher then the reduced noise level of the silencer

80 dB

90 dB the blow-off pipe is insulated, but the valve is not

© GLAUNACH GMBH

Edition 02.2007


Vent Silencers should not be installed in front or nearby a building. This causes noise reflections which increases the sound level.

silencers installed on the roof with optimum noise and safety performance

lethal installation inside a building

WARNING

- steam at the silencer outlet is extremely hot vent silencers must be installed in such a way, that no person can be exposed to the steam flow during blow off at any time

© GLAUNACH GMBH

Edition 02.2007


2. DEWATERING OF VENT SILENCERS

to avoid damage of the roof use a plate or a cup beneath the silencer drainage

don’t by- the drain the silencer may be damaged and the noise level will increase

the uninsulated dewatering pipe should be as short as possible

don’t elongate the drain pipe ice plugs may prevent dewatering

© GLAUNACH GMBH

Edition 02.2007


4. DIFF DESIGN GLAUNACH

OTHER

seamless diff pipes are used stainless-steel wire mesh reduce swirls

perforated plates are used as diff the absence of wire mesh cause flow noise

small borings achieve a higher noise reduction

perforated holes have a larger diameter with less noise reduction

for safety reasons all pressurized welds are tested

other manufacturer don’t care

© GLAUNACH GMBH

Edition 02.2007


5. ABSORBER DESIGN GLAUNACH

OTHER

strong and heat resistant glass fabrics cover absorbing materials

cheaper fleece materials are blown out shortly

absorbers are totally made from stainless steel

absorbers made from carbon steel will rust out shortly

continuous welding on all parts guarantees long service life

cheaper spot welding results in vibrations and early fatigue

© GLAUNACH GMBH

Edition 02.2007


6. CATASTROPHIC FAILURES BY POOR DESIGN In the last years, we’ve repaired and replaced many silencers from other manufacturers. At the following example, the steam jet hits the head of the diff with sonic speed and high temperature. This destroyed the diff immediately and furthermore destroyed the core of the absorber and blew it away.

poor design

destroyed diff

absorber blew out

The diff cage and absorber was removed and replaced by a Glaunach Diff. Now the silencer works without any problems.

silencer repaired by Glaunach © GLAUNACH GMBH

replacement of diff

installation of the repaired silencer Edition 02.2007


Another example of a catastrophic failure caused by a cost saving design. The absorber blew out of the silencer and hit the ground.

© GLAUNACH GMBH

Edition 02.2007

Glaunach Silencer Handbook 6l1r34

Overview 4q3b3c

More details 26j3b

Related Documents 171j1w

Glaunach Silencer Handbook 6l1r34

Aqua Silencer 5m2e3k

Aqua Silencer 5m2e3k

Silencer Application 3j6y4t

Homemade Silencer 472k2c

Vent Silencer Spec Sheet 3m3425

More Documents from "riff" 2v4b1c

10 Steps In Compost Production 6h1l46

Canonipf - Reset Maintenance Tank 5h4x73

Glaunach Silencer Handbook 6l1r34

Contoh Label High Alert 563g4j

Whittling Is Easy 11b4k