Application Form 5z4mo

Table of Contents

TABLE OF CONTENTS Pages Surface Preparation Paint Problem Defects Estimating Paint Requirements Painting Specification Product Information

.............................................................. .............................................................. ..............................................................

Acrylic Water-Based Paint ........................................................ Boysen Decore .............................................................. Boysen Permacoat Wallguard Dirt Resisting Latex #5715 ................ ....................... ................ Boysen Permacoat Lo-Odor Latex Boysen Skimkote #7750 .............................................................. Boysen Permacoat Flat Latex .................................................... Boysen Permacoat Semi-Gloss Latex #7l5 ................................. Boysen Permacoat Gloss #710 ................................................ Boysen Roofgard .............................................................. Boysen Permatex #3101 ........................................................ Boysen Multi-fleck Technicolor Paint ........................................... Boysen Primeguard .............................................................. Boysen Clear Acrylic Emulsion #700 ........................................ Boysen Masonry Putty #7311 ............................................... Boysen Plexibond #7760 ........................................................

:

Enamel Paint .............................................................. Boysen Flatwall Enamel M O O .................................................. Boysen Semi-Gloss Enamel #200 ............................................. Boysen Quick Drying Enamel ................................................... Boysen School Board Slating, Green #655 .................................. Boysen Plasolux Glazing Putty #31 1 ......................................... Boysen Plasolux Primer Surfacer #307 ...................................... Boysen Red Oxide Primer #3lO ............................................... ........................................ Boysen Zinc Chromate Yellow #320 ............................................. Boysen Red Lead Primer #37O Boysen Aquaseol #99 ............................................................ .................................. Boysen Silver Finish Aluminum Paint #75 ............................... Boysen Heat Resisting Aluminum Paint #95 Boysen Heat Resisting Aluminum Paint #83 ................................ Boysen Bridge and Tank Aluminum Paint #85 ............................. Boysen Reflectorized Traffic Paint .............................................. Boysen Alkyd Traffic Paint .......................................................

Table of Contents

3 6 7 9 17

....................................................................................

Stains Boysen Xyladecor ................................................................... Boysen Oil Wood Stain ...........................................................

Lacquer Paint ............................................................................. Boysen Lacquer Primer Surfacer #305 ....................................... Boysen Lacquer Spot Putty #306 ............................................... Boysen Gloss Lacquer Enamel #I200 ........................................ Boysen Clear Gloss Lacquer #I250 .......................................... Boysen Clear Dead Flat Lacquer #I253 ................................... Boysen Lacquer Sanding Sealer #I254 .................................... Boysen Water White Clear Gloss Lacquer #I258 ......................... Boysen Automotive Lacquer #I300 ........................................... Acrylic Solvent-Based Paint ........................................................... Boysen Actytex Clear Coat #I700 ............................................ Boysen Actytex ...................................................................... Boysen Actytex Cast #171 1 ..................................................... Boysen Actytex Primer #I705 ................................................. Epoxy Paint .............................................................................. Boysen Epoxy Primer .............................................................. Boysen Epoxy Enamel ............................................................ Boysen Acqua Epoxy ............................................................. Polyurethane Paint ........................................................... Boysen Poly-U 2K Paint ......................................................... Boysen Poly-U Reducer #I805 ................................................ Hudson Polyurethane Floor Varnish Sealer ................................. Hudson Polyurethane Floor Varnish Topcoat ................................

...........................................................................

Allied Products Boysen Masonry Neutralizer #44 ............................................... Boysen Metal Etching Solution #71 ........................................... Boysen Paint and Varnish Remover # I 4 1 ................................... Boysen Masonry Surface Conditioner #304 ................................. Nation Wood Bleach 1 & 2 ...................................................... Boysen Spar Varnish #58 ........................................................ Boysen Tinting Products Boysen Latex Color .......................................................... 8oysen Oil Tinting Color ................................................... Boysen Acryiex Tinting Color .............................................. Boysen Automotive Tinting Color .........................................

Table of Contents

SURFACE PREPARATION

Table of Contents

A. Surface Preparation Prepare surfaces in a skillful manner to produce finished work of first class appearance and durability. Surfaces must be free of dust, dirt, oil grease and other foreign matter prior to the primer coat. Be sure surface is clean and dry. Repair all voids, nicks, cracks, etc., with suitable patching material. O n puttying: - Use Boysen Masonry Putty for interior latex systems, Boysen Acrytex Cast for exterior surfaces. Use Boysen Plasolux Glazing Putty for alkyd oil-based systems. - Use Boysen Lacquer Spot Putty for lacquer-based systems. Apply at least a coat of anti-corrosive paint on ferrous metal. Take note that their effectiveness is directly related to film thickness. Use the appropriate metal primer. Remove all foreign matter. For very smooth metal surfaces, lightly sand to provide paint film anchorage. Clean entire surface of galvanized metal with paint thinner or soap and water. Rinse thoroughly and let dry. Apply a coat of desired primer on the same day.

0

a a

-

a

a

The following are surface preparation specifications for different surfaces: ALUMINUM Remove corrosion by wire brushing, oil, grease and other foreign matter with solvent or steam. BRASS, BRONZE, COPPER, LEAD Remove contaminants with a combination of water detergent and solvents. Allow the metal to dry and remove oxides by power or hand abrade. BRICK- EXTERIOR OR INTERIOR Remove dirt, dust, loose or excess mortar by brush, air or steam cleaning. Remove efflorescence on bricks exposed for some time by wire brushing, followed by a water rinse. Allow to dry. CHISELED, SANDBLAST AND RUBBLEWORK Remove loose materials used. Surfaces should be clean, dust free and thoroughly dr/ for excellent absorption and adhesion of Boysen Aquaseal #99.

-

CONCRETE EXTERIOR AND INTERIOR (Poured, Plastered, Stucco, Hollow Blocks) Remove all loose grit, mortar, dust, dirt, grease, oil and any other foreign matter. Allow new plastered wall to cured for 14 to 28 days before neutralization. Treat new masonry with 1 :16 mixture of Boysen Neutralizer #44 and water respectively. Allow to dry overnight before sanding or rinsing with water to remove white residue. For chalking old latex paint, use Boysen Masonry Surface Conditioner #304. Treat any mould or fungus infestation with Boysen Fungicidal Wash Solution #74 or Bleaching Solution (1 :3).

3 Table of Contents

GALVANIZED IRON Clean thoroughly to remove dust, foreign matter, oil or grease using Boysen Paint Thinner or Boysen Lacquer Thinner. For new galvanized iron, treat with 10% Boysen Metal Etching Solution (1 part Boysen Metal Etching Solution to 9 parts of water). Then wipe off with rag soaked in Boysen Paint Thinner. Immediately apply Boysen Metal Primers before rusts sets in. METAL Metal must be free from oil, grease, dust and st. The most ideal surface preparation for rusty metal is sandblasting. Thin films of rust may be removed by wire brushing, sanding or scraping. Thicker layers of rust can be removed with the use of Boysen Metal Etching Solution. Metal surfaces cleared of rust must be immediately primed with Boysen Metal Primers. Do not allow bright metal to be exposed to the weather as rust will set in fast. WOOD Use only kiln dried (12% moisture) wood. If wood is stained, seal using Boysen Lacquer Sanding Sealer #1254. Sand rough wood until smooth. Countersink nailheads for putty application. Dust off surfaces completely and wipe with clean rag.

B. Application 8 Use either brush, roller or spray unless otherwise specified. Apply paints evenly, free from sags, runs, crawls and defects. Apply thin coats at a time, leaving a minimum number of brush marks. The number of coats specified is the minimum number acceptable. If full coverage is not obtained with the specified coats, apply additional coats as necessary to produce the required finish. C. Painting Schedule 8 Always start at the top and work downwards. 0 Finish surfaces in accordance with manufacturer's recommendation. Do not intermix paints of different types. 0 Be sure painting area is properly ventilated. For outdoors, paint only when the weather allows it. Do not paint under direct sunlight, on rainy days or during a very windy day.

Simple Guidelines for Repainting Inspect Painted Surfaces It is necessary to have o periodic inspection of interior and exterior surfaces by anyone familiar with paints and good painting practice. Experience indicates that considerable savings may be attained provided that maintenance painting is scheduled at the right time. By spot painting before any real damaged is done, the life of a paint job can be prolonged and maintenance painting costs are reduced substantially. 0

Table of Contents

* Surface Conditions and Preparation The most important in any repainting job is the surface preparation. This is because most of the problem in repainted jobs are caused by faulty surface conditions, inadequate preparation and moisture entry. Preparing surfaces properly will give you a much better final result. The extra time invested is worth it. It i s not advisable to simply apply a fresh coat of paint over a surface that already has a thick paint build-up. The adhesion between the new and old layers of paint coatings maybe weakened as the new paint expands and controls with changes in temperature. The old paint underneath will lose its elasticity and peel-off causing a paint failure. Better check if the existing paint is in good condition, its adhesion is of utmost importance. Do a test coot on a small area to establish suitability for recoating. Beware of peeling or flaking in the existing paint film. Cut a small cross-section in the old paint with a sharp blade. Apply masking tape over it and then remove, if the old paint comes off, the old paint film needs to be stripped. Scraping, wire brushing and sanding will remove lose paint in most areas. Applying a paint and varnish remover to facilitate scraping of old paint may be useful. In some cases, sandblasting may be necessary. Next, clean the surface thoroughly using the gentlest means possible yet achieving the level of cleanliness required. Water, chemical and mechanical methods are available for this purpose. Surface must be rid of dirt, dust, chalk, grease, wax polishes, alkali, soap films, etc. After the surface preparation, complete the priming operation as soon as possible. Use a suitable primer for a particular surface which is also compatible with the desired finish. , when painting never try to put too much paint on at once. Two coats at the recommended coverage rate are better than one overly thick coat.

Table of Contents

PAINT PROBLEM DEFFECTS ALLIGATORING An incomplete form of peeling, where the paint cracks into large segments. The edges of which break away from the surface while the center remains attached. Usually due to repeated application of new coats over old coats no longer adherent. BLEEDING Discoloration of a coating caused by soluble color in the underlying surface. May be prevented by applying an impermeable undercoating. BLISTERING Formation of blisters or pustules on a coating. May be due to underlying spots of grease, sap or moisture, to excessive heat or direct exposure to the sun during the process of drying. CHALKING Progressive powdering from the surface inward. Always choose the right type of paint for exterior purposes. DEADENING Loss of luster. May be due to insuificient or defective under coats, most frequently to improper filling of wood. MOISTURE BLUSH Clouding of the lacquer film through precipitation of moisture in the film. Constant temperature and constant low humidity in the finishing room will prevent much trouble. PEELING Indicates imperfect attachment to the surface. Common causes of peeling are due to dampness, greasy surfaces and moisture. PINHOLING The term describes the appearance. Causes are changes in atmospheric conditions during drying, application over sweating or incompletely dried undercoats, spots of grease or soap and cold draught. RUNS AND SAGS Irregularities of surface due to uneven flow of varnish or paint. Most frequenf causes are too much varnish, incomplete brushing and inelastic brush. TACKINESS The adhesive property of incompletely dried coating. Tackiness is caused especially in the refinishing of old work, by applying a coating over a greasy or unclean surface. WRINKLING Condition appears chiefly to application of few heavy coats for more thin ones. Also may be due to cold weather. Removal of the coats is the remedy.

6

Table of Contents

ESTIMATING PAINT REQUIREMENTS 1. How to estimate quantity of paints, enamels and thinners especially on new large surface areas:

Area W e r s Coverage area per gallon per coat

= Quantity of Paints needed

Total Quantity of Lacquers or Enamel in aallon

4

= Quantity of lacquer thinner and paint thinner needed

2. How to estimate labor needed: A skilled painter can brush on two (2) 4 liter cans in a day's work (8 hours). This estimate includes surface preparation and application of putty for minor surface imperfections. O n the average a skilled painter will ask P 250.00 for solar/ (plus P 50 for ECOLA) for a day's work.

Table of Contents

PAINTING SPECIFICATION

Table of Contents

MASONRY SURFACES I. INTERIOR SURFACES A. PLAIN FINISH Acrylic water-based type 1st coat Boysen Permacoat Flat Latex B-701 Boysen Masonry Putty 8-731 1 putty 2nd & 3rd coat Boysen Permacoat Latex Topcoat (Flat, Semi-Gloss, Gloss) Acrylic water-bared type (Repainting Only) 1st & 2nd coat Boysen Permacoat Lo-Odor Latex Topcoat (Flat, Semi-Gloss, Gloss) Acrylic solvent-based type 1st coat Boysen Acrytex Primer 8-1705 Boysen Acryiex Cast 8-171 1 putty 2nd & 3rd coat Boysen Acryiex Topcoat (Flat, Semi-Gloss, Gloss) Polyurethane type 1st coat Boysen Acryiex Primer 8-1 705 Boysen Acrytex Cast 8-1 71 1 putty 2nd & 3rd coat Boysen Poly-U 2K Paint (Flat, Semi-Gloss, Gloss) EPOXY type 1st coat 2nd & 3rd coat

Boysen Epoxy Primer Boysen Epoxy Enamel Boysen Acqua Epoxy

B. TEXTURED FINISHES Acylic water-based type 1st coat Boysen Permacoat Flat Latex B-701 putty Boysen Masonry Putty B-7311 Texture Boysen Permatex B-3101 2nd & 3rd coat Boysen Permacoat Latex Topcoat (optional) Acrylic water-based type 1st coat Boysen Permacoat Flat Latex 8-701 Boysen Masonry Putty 8-731 1 putty 2nd coat Boysen Permacoat Latex Texture Boysen Multifleck 8-2400 Clear Topcoat Boysen Acrytex Clear B-1700 (optional) Acrylic water-based type 1st coat Boysen Permacoat Flat Latex 8-701 Boysen Masonry Putty 8-731 1 putty Boysen Decors Undercoat 8-4605 2nd coat Texture Boysen Decore Base B-4610 + Toner (any desired color) 11

Table of Contents

Acrylic solvent-based type 1st coat Texture 2nd & 3rd coat

Boysen Acrytex Primer 8-1 705 Boysen Acrytex Cast B- 17 1 1 Boysen Acrytex Topcoat (Flat, Semi-Gloss, Gloss)

II. EXTERIOR SURFACES A. PLAIN FINISH Acrylic water-based type 1st coat putty 2nd & 3rd coat

Boysen Permacoat Flat Latex B-701 Boysen Acrytex Cast B- 1 7 11 Boysen Permacoat Latex Topcoat (Flat, Semi-Gloss, Gloss)

Acrylic water-based type 1st coat puth/ 2nd & 3rd coat

Boysen Acrytex Primer 8-1 705 Boysen Acrytex Cast B- 17 1 1 Boysen Permacoat Wallguard (Semi-Gloss)

Acrylic water-based type 1st coat puny 2nd & 3rd coat

Boysen Permacoat Flat Latex B-701 Boysen Acrytex Cast B-1711 Boysen Roofgard

Acrylic solvent-based type 1st coat putty 2nd & 3rd coat

Boysen Acrytex Primer 8-1 705 Boysen Acrytex Cast B-1711 Boysen Acrytex Topcoat ,(Flat, Semi-Gloss, Gloss)

Polyurethane type 1st coat putty 2nd & 3rd coat

Boysen Acrytex Primer 8-1 705 Boysen Acrytex Cast B-1711 Boysen Poly-U 2K Paint (Flat, Semi-Gloss, Gloss)

EPOXY trpe 1st coat 2nd & 3rd coat

Boysen Epoxy Primer Boysen Acqua Epoxy

B. TEXTURED FINISHES Acrylic solvent-based type 1st coal Texture 2nd & 3rd coat

Boysen Acrytex Primer B-1705 Boysen Acrytex Cast B-1711 Boysen Acrytex Topcoat (Flat, Semi-Gloss, Gloss)

Table of Contents

Acrylic cement modifier Texture Boysen Plexibond 8-7760 Primer Boysen Acrytex Primer 8-1 705 Boysen Permacoat Latex Topcoat (Flat, Semi-Gloss, Gloss) 2nd & 3rd coat Boysen Acrytex Topcoat (Flat, Semi-Gloss, Gloss) Boysen Poly-U 2K Paint Boysen Acqua Epoxy

WOOD SURFACES I. INTERIOR SURFACES A. PLAIN FINISH Alkyd type 1st coat putty 2nd & 3rd coat

Boysen Flatwall Enamel 8-800 Boysen Plasolux Glazing Putty B-311 Boysen Flatwall Enamel B-800

Alkyd type 1st coat putty 2nd & 3rd coat

Boysen Flatwall Enamel B-800 Boysen Plasolux Glazing Putty B-311 Boysen Semi-Gloss Enamel 8-200

Alkyd type 1st coat putty 2nd & 3rd coat

Boysen Flatwalf Enamel 8-800 Boysen Plasolux Glazing Putty 8-31 1 Boysen Quick Drying Enamel (any desired color)

Acrylic solvent-based type 1st coat Boysen Acrytex Primer 8-1 705 putty Boysen Acrytex Cast B-1711 Boysen Acrytex Topcoat (Flat, Semi-Gloss, Gloss) 2nd & 3rd coat EPOXY type 1st coat 2nd & 3rd coat

Boysen Epoxy Primer Boysen Epoxy Enamel Boysen Acqua Epoxy

Polyurethane type Boysen Acrytex Primer 8-1 705 1st coat putty Boysen Acrytex Cast B-1711 Boysen Poly-U 2K Paint (Flat, Semi-Gloss, Gloss) 2nd & 3rd coat

Table of Contents

DOORS, JAMBS, CABINETS, SHELVES Lacquer type 1st coat putty 2nd coat 3rd & 4th coat

Boysen Lacquer Primer Surfacer B-305 Boysen Lacquer Spot Putty 0-306 Boysen Lacquer Primer Surfacer 8-305 Boysen Automotive Lacquer 8-1300 Boysen Gloss Lacquer Enamel 8-1200

VARNISHING (door, jamb, cabinets, ling, etc.) Natural-lacquer type 1st coat Boysen Lacquer Wood Tife 6-61 Boysen Natural Wood Paste Filler 8-60 2nd to 4th coat Boysen Lacquer Sanding Sealer 8-1254 5th & 6th coat Boysen Clear Gloss Lacquer B-1250 Boysen Water White Clear Gloss Lacquer 8-1258 Boysen Clear Dead Flat Lacquer 8-1253 Wood stain-lacquer type 1st coat Boysen Lacquer Wood-Tite 8-61 Boysen Natural Wood Paste Filler B-60 2nd coat Boysen Oil Wood Stain 3rd to 5th coat Boysen Lacquer Sanding Sealer 8-1254 6th & 7th coat Boysen Clear Gloss Lacquer 8- 1250 Boysen Water White Clear Gloss Lacquer 8-1258 Boysen Clear Dead Flat Lacquer 8-1253 Stained-lacquer type 1st coat Nation Wood Bleach 1 & 2 (optional) 2nd & 3rd coat Boysen Xyladecor 4th to 6th coat Boysen Lacquer Sanding Sealer 8-1254 7th & 8th coat Boysen Clear Gloss Lacquer 8-1250 Boysen Water White Clear Gloss Lacquer B-1258 Boysen Clear Dead Flat Lacquer 8-1253 Stained-polyurethane type 1st coat Nation Wood Bleach 1 & 2 (optional) 2nd & 3rd coat Boysen Xyladecor 4th to 6th coat Hudson PU Floor Varnish Sealer 7th & 8th coat Hudson PU Floor Varnish Topcoat Natural-polyurethane type 1st to 3rd coat Hudson PU Floor Varnish Sealer Hudson PU Floor Varnish Topcoaf 4fh & 5th coat

Table of Contents

B. TEXTURED FINISHES Acrylic solvent-based type 1st coat Texture 2nd & 3rd coat

Boysen Acrytex Primer 8-1705 Boysen Acrytex Cast B-1711 Boysen Acrytex Topcoat (Flat, Semi-Gloss, Gloss)

Acrylic water-based type 1 st coat Boysen Flatwall Enamel B-800 putty Texture 2nd & 3rd coat

Boysen Plasolux Glazing Putty 8-31 1 Boysen Permatex 8-3101 Boysen Permacoat Latex Topcoat (optional)

Acrylic water-based type 1 st coat Boysen Flatwall Enamel 8-800 putty 2nd coat Texture

Boysen Plasolux Glazing Putty B-311 Boysen Flakall Enamel B-800 Boysen Multifleck

Acrylic water-based type 1st coat putty 2nd coat Texture

Boysen Flatwall Enamel 8-800 Boysen Plasolux Glazing Putty B-311 Boysen Decore Undercoat B-4605 Boysen Decore Base B-4610 f Toner (any desired color)

11. EXTERIOR SURFACES A. PLAIN FINISH Polyurethane type 1st coat puny 2nd & 3rd coat

Boysen Acrytex Primer 8-1705 Boysen Acrytex Cast 8-1 71 1 Boysen Poly-U 2K Paint (Flat, Semi-Gloss, Gloss)

Alkyd type 1st coat putty 2nd & 3rd coat

Boysen Flaiwall Enamel B-800 Boysen Plasolux Glazing Putty 8-31 1 Boysen Quick Drying Enamel (any desired color)

Acrylic solvent-based type 1st coat putty 2nd & 3rd coat

Boysen Acrytex Primer 8-1 705 Boysen Acrytex Cast B-1711 Boysen Acrytex Topcoat (Flat, Semi-Gloss, Gloss)

EPOXY type 1st coat 2nd & 3rd coat

Boysen Epoxy Primer Boysen Acqua Epoxy

Table of Contents

Stained Finish 3 coats

Boysen Xyladecor

B. TEXTURED FINISHES Acrylic solvent-based type Boysen Acrytex Primer 8-1 705 Ist coat Boysen Acrytex Cast B-1711 Texture Boysen Acrytex Topcoat (Flat, Semi-Gloss, Gloss) 2nd & 3rd coat

GALVANIZED IRON/METAL SURFACES A l W type Ist coat

2nd & 3rd coat

Primer, choice of: Boysen Red Lead Primer 8-370 Boysen Red Oxide Primer B-310 Boysen Zinc Chromate Primer Yellow 8-320 Boysen Quick Drying Enamel (any desired color) Boysen Bridge & Tank Aluminum B-85 Boysen Silver Finish Aluminum 8-75

Acrylic water-based type 1st coat Boysen Primeguard B-4310 Boysen Roofgard 2nd & 3rd coat Epoxr type Ist coat

2nd & 3rd coat

Primer, choice of Boysen Primeguard 8-43 10 Boysen Epoxy Primer 8-2200 Boysen Epoxy Red Lead Primer B-2270 Boysen Epoxy Zinc Chromate Primer 8-2260 Boysen Acqua Epoxy Boysen Epoxy Enamel (interior only)

FOR DRINKING WATER TANK (Interior) Boysen Epoxy Primer White 8-2200 1st coat Boysen Epoxy Enamel White 8-2 100 2nd & 3rd coat Note: Curing time of applied paint in tank before use is seven (7) days.

Table of Contents

PRODUCT INFORMATION

Table of Contents

ACRYLIC WATER BASED PAINT

Table of Contents

bysen DECORe DESCRIPTION: Boysen DECORe is a unique water-based decorative paint system that can simulate the complex texture and distinctive finish of the European masters right in your home. Unlike traditional faux finishes, Boysen DECORe does not need elaborate intermixing of colors, layering techniques or sophisticated equipment. Simple effortless, brushing is all that's required to achieve this very exquisite finish. PRINCIPAL USES PRACTICAL COVERAGE SURFACE DRY THINNING APPLICATION PACKAGING

Use it on concrete walls, wood and drywalls for interiors DECORe Undercoat - 20 25 sq.m./gol/coat DECORe Base Toner - 25 -30 sq.m./gal/coat Two (2) hours Use as supplied. By brush using 3" Diamond (China) brush and Boysen DECORe plastic scraper 4-liters B-4605 DECORe Undercoat 4-liters 8-4610 DECORe Base 200 ml B-4700 DECORe Toner

+

-

AVAILABLE COLORS: B4730 Light Gray 84741 Aqua Blue 84742 Light Blue B4743 Deep Blue 84750 Dark Green 84762 Medium Yellow 84763 Bright Yellow 84771 Soft Red B4772 Brick Red 84780 Brown SURFACE PREPARATION Allow new masonry to dry for 14 to 28 days under normal weather conditions before painting. Surface to be painted should be clean and dry, free from oil, grease, dust, dirt, contaminants and all loose grit and mortar. Treat new masonry with a solution of 1 part Boysen Masonry Neutralizer #44 diluted in 16 parts water, applying liberally by brush or roller. Let dry overnight before rinsing with water to remove white crystals that form on the surface. Let dry before painting. Repainting Remove all loose, scaling, flaking and peeling off paint by using Boysen Paint and Varnish Remover #141, wire brushing, scraping orwater blasting. Let it dry. For chalking old paint, use

Table of Contents

Boysen Masonry Surface Conditioner #304 as primer. In case of mildew infestation, treat with Boysen Fungicidal wash Solution #74 by swabbing or brushing. To ensure proper treatment, allow to remain on the surface for 24 hours. Let dry. PAINTING SCHEDULE Apply Boysen Permacoat Flat Latex #701 as primer for concrete. For wood, use Boysen Flatwall Enamel #800. For repainting, no need to apply primer. After primer application, apply Boysen DECORe Undercoat #4605 by brush or roller and fully cover the surface. Let dry. Note : The design can only be achieved using Boysen DECORe Undercoat. After choosing the desired color, mix Boysen DECORe Toner into Boysen DECORe Base #4610. A color can be applied in different tones by varying amount of toner used, either Full, One-half, One-Fourth, or any other proportion depending on desired shade. Stir until uniform consistency is achieved. DO NOT THIN MIXTURE WITH WATER OR ANY SOLVENT. Using a 3" Diamond (China) Boysen DECORe brush, apply from top corner, working with short crisscrossing strokes. If a more uniform pattern is desired, stroke with a clean brush while paint is still wet. Note: The design may not be achieved if a different paint brush is used. Allow 8 to 10 minutes after applying Boysen DECORe before lightly combing using the plastic scraper again in long crisscrossing strokes, with the scraper inclined and close to the surface.

Table of Contents

Boysen Permacoat Wallguard Dirt Resisting Latex #5715 Introducing a new breed of latex paints that has a very high resistance to dirt, dust, smog and mildew. It can be painted even in a rigorous environment where there is a very high concentration of airborne pollutants. DESCRIPTION: Boysen Permacoat Wallguard Dirt Resisting Latex Paint is suitable to be used near industrial areas and along highways. It is specially suited for repainting medium and high rise building where the need to maintain a freshly painted look with less maintenance is of prime importance. Highly Resistant to airborne pollutants and dud 100% Acrylic Highly alkaline resistant Resist fading, cracking and peeling Good exterior durability Excellent gloss retention Mildew resistant Good block and scrub resistance PRINCIPAL USES: Use Boysen Permacoat Wallguard as an exterior finish for newly constructed building as well as repainting old structures.

-

APPLICATION PACKAGING

25 30 square meters/ gal. /coat Thirty (30) minutes 1.5 mils /coat Allow two hour before recoating. Use as supplied. If necessary, thin with not more than 'h liter of water per 4-liter can paint brush, roller or airless spray 4-liter cans

AVAILABILITY

Semi-Gloss #5715

PRACTICAL COVERAGE SURFACE DRY DRY FILM THICKNESS OVERCOATING INTERVAL THINNING

:

COLORANTS: Use only Boysen Latex Colors for tinting to achieve pastel shades. To produce dark shades, use factory mixed colors. SURFACE PREPARATION New Masonry Allow new masonry fo dry for 14 (for exterior surfaces) to 28 days (for interior surfaces) under normal weather conditions before painting. Surface to be painted should be clean and dry, free from oil, grease, dust, dirt, contaminants, and all loose grit and mortar. Treat new masonry with a solution of 1 part Boysen Masonry Neutralizer #44 diluted in 16 parts water, applying liberally

Table of Contents

by brush or roller. Let dry overnight before rinsing with water to remove white crystals that form on the surface. Let dry before painting. Repainting Remove all loose, scaling, flaking and peeling off paint using Boysen Paint and Varnish Remover

#141, wire brushing, scraping, or pressure washing. Let it dry. Sand smooth painted surfaces for improved adhesion. In case of mildew infestation, treat with Boysen Fungicidal Wash Solution

4474 by swabbing or brushing. To ensure proper treatment, allow to remain on the surface for 24 hours. Let dry. PAINTING SCHEDULE New Painting Primer puw Topcoat

: : :

Boysen Actyiex Primer #I705 Boysen Actyiex Cast #I71 1 Boysen Permacoat Wallguard

(2coats)

Repainting Topcoat

Apply two coats of Boysen Permacoat Wallguard on properly prepared surface.

Table of Contents

Boysen Permacoat Lo-Odor Latex Finally, a non-disruptive paint that allows repainting during regular business hours because of its ultra low odor during application and drying, with n o residual paint smell after painting. DESCRIPTION: Boysen Permacoat Lo-Odor Latex Paint is ideal for repainting hospitals and health care facilities, offices, schools, commercial buildings, condos, apartments, residential areas and public spaces. Water based Environment friendly Not subiect to special storage requirements Rapid drying Low odor of paint enables faster resumption of service in painted areas. PRINCIPAL USES: Use Boysen Permacoat Lo-Odor Latex Paint for repainting interior concrete, dry wall and properly primed wood.

APPLICATION PACKAGING

25 - 30 square meters/ gal. /coat Thirty (30) minutes 1.5 mils /coat Allow one hour before recoating. Use as supplied. If necessary, thin with not more than liter of water per 4-liter can paint brush, roller or airless spray 4-liter cans

AVAILABILITY

Available in Flat #7701, Semi-Gloss #7715, Gloss #7710

PRACTICAL COVERAGE SURFACE DRY DRY FILM THICKNESS OVERCOATING INTERVAL THINNING

:

'/2

COLORANTS: Use only Boysen Latex Colors for tinting to achieve pastel shades. To produce dark shades, use factory mixed colors. SURFACE PREPARATION: Remove all loose, scaling, flaking and peeling off paint by using Boysen Paint and Varnish Remover #141, wire brushing, scraping, or water blasting. Let it dry. Sand smooth painted surfaces for improved adhesion. In case of mildew infestation, treat with Boysen Fungicidal Wash Solution #74 by swabbing or brushing. To ensure proper treatment, allow to remain on the surface for 24 hours. Let dry. Repainting Topcoat: Apply two coats of Boysen Permacoat Lo-Odor Latex Paint

Table of Contents

Boysen Skimkote #7750 DESCRIPTION: Boysen Skimkote #7750 is a special bonding paste that is mixed with cement and applied on concrete to correct surface imperfections prior to painting. It repairs bubbles, honeycomb and concrete defects on waviness and plumbness up to 4 mm thick. PRINCIPAL USES: For both interior and exterior plastered concrete, concrete slobs, acotech walls, reinforced concrete walls, and pre-cast concrete surfaces in lieu of cement plaster to eliminate surface defects and make the surface smooth and ready for painting. PRACTICAL COVERAGE : SURFACE DRY APPLICATION PACKAGING

POTLIFE

0.4kg/m2/mm, recommended total thickness is from 0.3 - 4 mm. 30 min.; allow two (2) days before painting. Apply with trowel or putty knife. 25 kg per pail Thirty (30) minutes

PAINTING RECOMMENDATION SURFACE PREPARATION 1. Remove oil, grease, dust, dirt, contaminants, and all loose grit and mortar from the surface. 2. Defects on concrete more than 5 mm thick should be corrected using mechanical sanders/grinders. 3. Moisten the concrete before application.

MIXING PROCEDURE Put Boysen Skimkote At7750 on a suitable container (plastic bucket) and mix it at 1 :1 ratio by weight until a lump-free homogeneous paste is reached. Do not add water. Use portland cement (for ordinary cement color) or white cement (to produce a white finish). The latter is suggested if Skimkote is to be topcoated with light-shaded paints.

APPLICATION 1. Using a steel trowel, apply the mixture thinly on the surface by pressing the edge of the trowel firmly on the concrete until all areas are covered. 2. Let it dry for at least 30 minutes before applying the second coat (if necessary). 3. If trowel marks are visible, let surface dry for at least 30 minutes before sanding to further smoothen surfaces. 4. No need to neutralize the surface. Allow at least 2 days before painting.

Note: Do not apply on painted surfaces.

Table of Contents

Boysen Permacoat Flat Latex DESCRIPTION: Boysen Permacoat Flat Latex Point is a 100% acrylic base paint that has low odor non-toxic, non-flammable with outstanding color retention. It contains the best fungicide to prevent mold and mildew growth. PRINCIPAL USES: For interior and exterior such as concrete, stucco, bricks plaster and hollow blocks. Also used for properly primed wood. PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION PACKAGING

25-30 square meters per 4 liters per coat Thirty (30) minutes Two (2) hours 1-1.5 mils/coat Allow one hour before recoating. Use as supplied. If necessary, thin with not more than 'h liter of water per 4-liter cans point brush, roller or airless spray 16-liter can and 1-liter (white only); 4-liter cans

AVAILABLE COLORS: B701 White B702 Off White 8721 Cream 8723 Moonlight 8725 Bone Ivory 8771 Tile Red B780 Chocolate Brown COLORANTS: Use only Boysen Latex Colors for tinting to achieve pastel shades. To produce dark shades, use factory mixed colors. Do not use Hansa Yellow B-1466 and Toluidine Red B1407 for exterior applications. PAINTING SCHEDULE 1st Coot putty 2nd & 3rd Coat

Boysen Permacoat Flat Latex #701 Boysen Masonry Putty #731 1 (interior use) Boysen Acrytex Cast # I 7 1 1 (exterior use) Boysen Permacoat Flat Latex Topcoat (any desired colors)

Repainting Remove all loose, scaling, flaking and peeling off paint using Boysen Paint and Varnish Remover #141, wire brushing, scraping, or water blasting. Let it dry. For chalking old paint, use Boysen Mosonry Surface Conditioner #304 as primer. In case of mildew infestation, treat with Boysen Fungicidal Wash Solution #74 by swabbing or brushing. To ensure proper treatment, allow to remain on the surface for 24 hours. Let dry.

Table of Contents

Boysen Permacoat Semi-Gloss Latex #715 DESCRIPTION: Boysen Permacoat Semi-Gloss Latex Paint is a 100% acrylic base paint that has low odor non-toxic, non-flammable with outstanding color retention. It contains the best fungicide to prevent mold and mildew growth. PRINCIPAL USES: For interior and exterior such as concrete, stucco, bricks plaster and hollow blocks. Also used for properly primed wood. PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION PACKAGING

25-30 square meters per 4 liters per coat Thirty (30) minutes Two (2) hours 1- 1.5 mils/coot Allow one hour before recoating. Use as supplied. If necessary, thin with not more than %liter of water per 4-liter cans paint brush, roller or airless spray 16-liter and 4-liter cans

COLORANTS: Use only Boysen Latex Colors for tinting to achieve pastel shades. To produce dark shades, use factory mixed colors. Do not use Hansa Yellow 0-1466 and Toluidine Red 81407 for exterior applications. PAINTING SCHEDULE 1st Coat putty 2nd & 3rd Coat

Boysen Permacoat Flat Latex #701 Boysen Masonry Putty #7311 (interior use) Boysen Acrytex Cast # I 7 1 1 (exterior use) Boysen Permacoot Semi-Gloss Latex Topcoat (any desired color)

Repainting Remove all loose, scaling, flaking and peeling off paint using Boysen Paint and Varnish Remover #141, wire brushing, scraping, or water blasting. Let it dry. For chalking old paint, use Boysen Masonry Surface Conditioner #304 as primer. In case of mildew infestation, treat with Boysen Fungicidal Wash Solution #74 by swabbing or brushing. To ensure proper treatment, allow to remain on the surface for 24 hours. Let dry.

Table of Contents

Boysen Permacoat Gloss Latex #710 DESCRIPTION: Boysen Permacoat Gloss Latex Paint # 7 1 0 is a 100% acrylic base paint that has low odor non-toxic, non-flammable with outstanding color retention. It contains the best fungicide to prevent mold and mildew growth. PRINCIPAL USES: For interior and exterior such as concrete, stucco, bricks plaster and hollow blocks. Also used for properly primed wood. PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION PACKAGING

25-30 square meters per 4 liters per coat Thirty (30) minutes Two (2) hours 1-1.5 mils/coat Allow one hour before recoating. Use as supplied. If necessary, thin with not more than %liter of water per 4-liter cans paint brush, roller or airless spray 16-liter, 4-liter and 1-liter cans

COLORANTS: Use only Boysen Latex Colors for tinting to achieve pastel shades. To produce dark shades, use factory mixed colors. Do not use Hansa Yellow 3-1466 and Toluidine Red B1407 for exterior applications. PAINTING SCHEDULE 1st Coat putty 2nd & 3rd Coat

Boysen Permacoat Flat Latex #701 Boysen Masonry Putty #7311 (interior use) Boysen Acrytex Cast #171 1 (exterior use) Boysen Permacoat Gloss Latex Topcoat (any desired color)

Repainting Remove all loose, scaling, flaking and peeling off paint using Boysen Paint and Varnish Remover #141, wire brushing, scraping, or water blasting. Let it dry. For chalking old paint, use Boysen Masonry Surface Conditioner #304 as primer. In case of mildew infestation, treat with Boysen Fungicidal Wash Solution #74 by swabbing or brushing. To ensure proper treatment, allow to remain on the surface for 24 hours. Let dry.

Table of Contents

Boysen Roofgard DESCRIPTION: Boysen Roofgard is a gloss acrylic, water-based roof paint designed to proted and adhere to galvanized surfaces. It gives a durable and flexible film, fast-drying time and good gloss retention. PRINCIPAL USES: For galvanized iron surfaces, pre-painted galvanized sheet, asbestos cement and unglazed tiles. PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION PACKAGING

25-30 sq.m./gat./coat Thirty (30) minutes Two (2) hours 1.5 mils/coat Two (2) hours Maximum 1/2-liter water per 4-liters paint By brush, roller or airless spray. Clean equipment with soap and water after use 4-liter and 16-liter cans

AVAILABLE COLORS: 82501 Laguna White 82520 Samar Beige 82540 Pacific Blue 82550 Baguio Green 82560 Orient Gold 82570 Spanish Red

* Colorants: Use Boysen Latex Colors for tinting to achieve pastel shades. To obtain darker colors, intermix standard colors or request for a factory mix color. SURFACE PREPARATION For unpainted galvanized iron sheets, etch the surface by applying 10% Boysen Metal Etching Solution #71 (dilute 1 part of 8-71 to 9 parts water). Wipe the surface with rag soaked in Boysen Paint Thinner #0340 to remove grease. Rinse with water and let dry. For prepainted galvanized iron sheets, scuff sand surface using sandpaper and wipe the surface with clean rag before applying paint. Spot prime if necessary. For corroded G.I. surfaces, remove rust by wire brushing and use Boysen Metal Etching Solution #71. Let it stay for 10-15 minutes. Be sure to wash off surface thoroughly with water or paint thinner and let dry. Prime immediately after drying. For new asbestos cement s and unglazed tiles (tegula), treat surfoce with Boysen Masonry Neutralizer #44. Let stand overnight and rinse.

Table of Contents

PAINTING SCHEDULE Galvanized Iron Sheets Boysen Red Oxide #310, Boysen Red Lead Primer #370, Boysen Zinc Primer Chromate Primer #320, Boysen Primeguard #4310 Asbestos s, Unglazed tiles Boysen Acrytex Primer #I705 Topcoat

Boysen Roofgard (2-3 coats ; any desired color)

Repainting For G.I. sheets with paint in good condition, clean surface of dirt and dust by washing and apply two coats of Boysen Roofgard.

Table of Contents

Boysen Permatex #3101 DESCRIPTION: Boysen Permatex #3101 is a water-based, full-bodied paint that dries to a fine rubbery coating, creating' a beautiful textured finish on interior walls and ceilings bringing elegance to your home interior. It adheres easily on wood, masonry, or fiber cement board surfaces. Conceals hairline cracks and minor surface imperfections, and dries to a fine rubbery coating that does not become brittle, leaving virtually no room for cracking, chipping, or peeling off. PRINCIPAL USES: For interior wood and masonry surfaces. PRACTICAL COVERAGE SURFACE DRY DRY THROUGH THINNING PACKAGING

-

5 6 sq.m./gal. Two (2) hours Overnight Use as supplied. If necessary, thin with not more than 1/2liter of water per 4-liter cans 4-liter cans

APPLICATION: For a regular texture pattern, apply Boysen Permatex #3101 straight from the can using a regular pattern roller. If a different design pattern is desired, first apply Boysen Permatex #3101 using a regular pattern roller. While paint is still wet and workable, press desired design pattern roller over wet paint and roll in one direction to impress the design onto the surface. For a uniform texture, be sure to maintain paint viscosity. PAINTING SCHEDULE

WOOD 1st Coat putty Texture 2nd & 3rd coat (optional)

:

MASONRY 1st Coat putty Texture 2nd & 3rd coat : (optional)

Boysen Flatwall Enamel #800 Boysen Glazing Putty #311 Boysen Permatex #3 101 Boysen Permacoat Latex (any desired color)

Boysen Permacoat Flat Latex #701 Boysen Masonry Putty #7311 Boysen Permatex #3101 Boysen Permacoat Latex (any desired color)

Table of Contents

Boysen Multi-fleck Technicolor Paint DESCRIPTION: Boysen Multi-fleck #2400 is a water-based technicolor paint that ingeniously affords the decorator the styling element of pattern - a richness of surface previously achieved only by the use of wallpaper. Unlike wallpaper that has seam and ting related problems, Boysen Multi-fleck mixes into the decorating scheme more readily because of the subtlety of its patterns, creating the appearance of "seamless wallpaper". It is more economical than wallpaper, easier to apply, and does not peel or crack. It hides wall imperfections very well, and can easily be repaired without leaving a trace because of its seamless properties. With 20 basic colors that can be mixed and matched to form an infinite number of color combinations, Boysen Multi-fleck allows the decorator complete freedom to create patterns to suit every possible mood. It is also versatile in application, and can be applied on almost any substrate and over any type of paint. PRINCIPAL USES: Superior for interior concrete, wood and metal surfaces. Application & Equipment Apply by spray only. Ensure adequate ventilation during opplication and drying. Shake well and stir gently before use. Do not thin. Use an air compressor (minimum 'h horsepower) that can deliver optimum pot pressure of 40 to 50 psi, and an ordinary internal mix type spray gun with medium-large nozzle attachment such as the following:

* Sprayit 527 (internal mix type air cap #3) * Binks 830 (Binks A81 air cap - 1 mm nozzle) * De VilBiss (281 air cap) Use the cross lap method of spray application. Hold the gun at right angles to the surface about 1 'h 2 feet owoy - do not flex the wrist while spraying. Air pressure should be constant during application to ensure continuity of pattern. After spraying, flush equipment with water then rinse with lacquer thinner.

-

Boysen multi-fleck can be applied over masonry, wood, metal, and any painted surfaces. All surfaces should be cleaned before application and completely free of dirt, dust, grease and loose or flaking materials. PRACTICAL COVERAGE: Sparse 8-10 sq. meters per liter Medium Dense 6-8 sq. meters per liter Super Dense 2-3 sq. meters per liter

Table of Contents

SURFACE DRY DRY THROUGH THINNING PACKAGING

Two (2) hours Overnight Not necessary 1-liter can (Special color combinations can be mixed at the Boysen Plant)

PAINTING SCHEDULE:

Masonry Surfaces Latex System

Acrytex System --- - - - -- _1 B1705-Acrytex Primer B701 -Permacoat Flat Latex White 1 --

P

Primer

-

puny Basecoat

8731 1 Masonry Putty

Final Coat

Boysen Multi-fleck

I '

B17 11-Acrytex Cast

8701 -Permacoat Flat Latex White B1701-Acrytex Flat White

-. --

Boysen Multi-fleck

-I I

Wood Surfaces

y I ( E n o m e l S y s t e m J ( A

cwex System

lPrimerI(B800-Flatwolll/~i 705-Acrytex Primer White --

Ilputtv

11~311 -Plasolux Glazina Putb

IlBl 71 1-Acrviex Cast

-

-

7

-

[~asecoat

IrB800-~latwall~ G eWhite l

]lBl%l-~ctytexFlat White

l ~ i n aCoat l

I[Boysen Multi-fleck

ll~oysenMulti-fleck

Metal Surfaces

~

-~ B ~ O

~

\

/

I

B

o

jIBoysen Metal Primer

--

- II

O - F I ~ n~a m~e white/ ~W ~ B600-Quick Drying Enamel Jlwhite -y

s

eMulti-fleck n

I 82100-Epoxy Enamel White

llBoysen Multi-fleck

A thin clear overcoat of B -1 700 Acryiex Clear may be applied by spray if a glossier finish is desired over Latex and Acrytex basecoats, but not over enamel basecoats. Repainting Old paint finish in bad condition should be stripped. After which the system for new surfaces are followed.

Table of Contents

/I I

Boysen Primeguard DESCRIPTION: Boysen Primeguard is a water-based acrylic maintenance primer designed to have excellent adhesion and metal ivotion. Boysen Primeguard is used where superior protection and good adhesion on hard-to-adhere metal surfaces is desired. It eliminates the need for a vinyl butyral wash primer tie coat. PRINCIPAL USES: For galvanized iron, stainless steel, aluminum, pvc pipes and other metal works such as iron ond steel frame. FEATURES AND BENEFITS

-

Exceptional adhesion as Boysen Primeguard has exceptional adhesion even on stainless steel and aluminum. It is also an environment-friendly alternative to traditional butyral wash primers. Corrosion Resistance- It ivates the metal substrate to provide good corrosion resistance on carbon steel. Rapid Drying dries in 20-30 minutes, compared to 8 hours for enamel primers. Recoat interval is 2 to 4 hours, resulting in faster paint jobs and significant labor cost savings. Thermoplastic Nature Remains flexible over time. It does not pose problems of intercoat adhesion and is capable of being topcooted by most solvent-based home coatings. Environmentally Safe It has low odor, is non-flammable, and does not use hazardous solvents. It does not contain lead and is non-toxic compared to troditonol anti-corrosive primers. Easy Water Cleanup no need for thinners and solvent reducers. Tools and painting equipment, spills and paint drips while still wet can be cleaned by water and soap solutions.

-

-

-

-

PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL APPLICATION PACKAGING

-

:

30 40 sq.m./4-liters/coat Thirty (30) minutes Two (2) hours 1.5 mils/coot Allow 2-4 hours before recoating. by brush, airless spray or roller 4-liter cans

AVAILABLE COLORS B4310 Primeguard Red Oxide

SURFACE PREPARATION

-

Metal Wipe the surface with rag soaked in paint thinner to remove dust, dirt, grease, oil, wax and other foreign matter. For new G.I. sheets, etch the surface by applying 10% Boysen Metal Etching Solution #71 (dilute 1 part of 8-71 to 9 parts water). If repointing, wire brush or scrape rusted metals and opply Boysen Metal Etching Solution #71 to remove all rust. Let it stay for 10-15 minutes. Be sure to wash off surface thoroughly with water, letting it dry before applying paint. Primer should be applied a few hours after application of B71 before rust sets in.

Table of Contents

PAINTING SCHEDULE New Metal 1st coat 2nd & 3rd coat

Boysen Primeguard Boysen Roofgard, Boysen Acqua Epoxy, Boysen Poly-U 2K, Boysen Epoxy Enamel, Boysen Acrytex, Boysen Quick Drying Enamel

Repainting It can be applied over old alkyd paint that is in good condition. Surface preparation prior to painting must be followed. It can be topcoated as in "new metal."

Table of Contents

Boysen Clear Acrylic Emulsion #700 DESCRIPTION: Boysen Cleor Gloss Acrylic Emulsion #700 is an acrylic type paint that acts as a barrier against dampness on new masonry. PRINCIPAL USES: improves performance of latex paint applied on damp new masonry. May be used as a clear gloss coating over interior surfaces of rubble, chiseled and sandblast finish. PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION PACKAGING

20-25 square meters per 4-liters per coat Thirty (30) minutes Two (2) hours 1-1.5 mils /coat Allow one hour before recoating. Use as su~died.If necessaw, thin with not more than 1/2liter of water per 4-liter can; paint brush, roller or airless spray 4-liter cans

SURFACE PREPARATION Allow new masonry to dry for 14 (for exterior surfaces) to 28 days (for interior surfaces) under normal weather conditions before painting. Surface to be painted should be clean and dry, free from oil, grease, dust, dirt, contaminants and all loose grit and mortar. Treat new masonry with a solution of 1 part Boysen Masonry Neutralizer #44 diluted in 16 parts water, applying liberally by brush. Let dry overnight before rinsing with water to remove white crystals that form on the surface. Let dry before painting. PAINTING SCHEDULE 1 st Coat 2nd Coat Topcoat

Boysen Permacoat Flat Latex #701 Boysen Clear Gloss Acrylic Emulsion #700 Boysen Permacoat Latex (flat, semi-gloss, gloss)

Table of Contents

Boysen Masonry Putty #7311 DESCRIPTION: Boysen Masonry Putty #7311 is a water based produd especially prepared for filling minor surface unevenness. Can also be used for full puttying. PRINCIPAL USES: For interior concrete, stucco, bricks plaster or any surface minor imperfection.

-

PRACTICAL COVERAGE SURFACE DRY DRY THROUGH OVERCOATING INTERVAL THINNING APPLICATION PACKAGING

:

Full Putty 10-12 sq. m. / gallon /coal Spot putty 25 sq. m. /gallon / coat Thirty (30) minutes Two (2) hours Allow two hours before recoating If necessary, thin with water. putty knife 16-liter, 4-liter and 1-liter cans

-

PAINTING SCHEDULE 1 st Coat Boysen Permacoat Flat Latex #701 PuV Boysen Masonry Putty #7311 Topcoat Boysen Permacoat Latex (flat, semi-gloss, gloss)

Note: Interior use only. For exterior, use Boysen Acryiex Cast # I 7 1 1

Table of Contents

Boysen Plexibond #7760 DESCRIPTION: Boysen Plexibond is a specially formulated acrylic polymer designed for compounding with Pozzolan o r Portland cement. The resulting mixture possesses excellent adhesion, water resistance and flexibility even o n thin section applications. Its use eliminates any cement plastering defects and water seepage, making it ideal for waterproofing roof decks and firewalls. It makes for a durable and decorative cementitious coating that not only enhances the appearance of light building materials but also prolongs their service life as well with its excellent weatherability. It offers excellent corrosion resistance when applied o n metal surfaces, and can also be used to improve adhesion to mortar patching and tile grouts. PRINCIPAL USES: Excellent adhesion to concrete, asbestos, bricks, wood and good corrosion resistance on metal surfaces such as G.I. sheets. FEATURES AND BENEFITS Outstanding flexibility - A thin section of ordinary cement is hard and brittle and crumbles easily, while cement modified with Plexibond possesses superior flexibility, thus eliminating cement plastering defects. The excellent adhesive and tensile strength balance of Boysen Plexibond maintains the integrity of the mortar. Excellent Water Resistance -When mixed with cement, Boysen Plexibond forms a seamless, nonporous impenetrable thick layer that disperses any liquid upon contad, preventing any water seepage when applied on both vertical and horizontal surfaces. Plexibond n has excellent sunlight exposure resistance, prolonging Resistant to Weathering - ~ o ~ s e the service life of light building materials such as marine plywood and cement asbestos boards.

-

Solvent-free Boysen Plexibond uses water for film cure, and thus has low odor, low flammability or other hazards inherent for solvent based systems. Retards Fire Spread - Boysen Plexibond is non-flammable, and retards flame spread when used as a cementitious coating for light building materials such as plywood. Excellent Corrosion Resistance -Boysen Plexibond offers good corrosion resistance on metal surfaces such as G.I. sheets when applied at a minimum thickness of 20 mils. Beautifies -Boysen Plexibond can be brushed on as a plaster finish or applied by textured roller or mortar gun, giving on attractive "orange peel" textured cementitious coating. The thin cementitious coating allows the preservation of architectural detail on wood, masonry, and metal surfaces. PRACTICAL COVERAGE SURFACE DRY DRY THROUGH

5 - 6 sq.m./gal. One (1) hour One (1) hour

Table of Contents

DRY FILM THICKNESS OVERCOATING INTERVAL THINNING PACKAGING

:

Approximately 2 0 mils Allow overnight before applying paint Not necessary 4-liter and 16-liter cans

SURFACE PREPARATION BOYSEN PLEXIBOND should be applied on bare concrete, wood, or metal NOT PREVIOUSLY PAINTED. Existing paint should be totally scraped off. Surface should be clean, free from oil, grease, dirt, any loose grit or mortar. Wet masonry surfaces first with water before applying PLEXIBOND mix to ovoid abrupt drying and cracking of the applied modified cement, especially under hot and sunny conditions. APPLICATION Mix 6.5 to 8 kgs. of cement to 4 liters of Boysen Plexibond. Add cement to Plexibond slowly while stirring to prevent lumping. mixture through a fine strainer to sift out lumpy materials. Ensure intimate mixing, stirring as often as possible to avoid settling. Keep mixture proportion constant for a uniform texture. Mix only enough material to prevent waste. Workability of Plexibond mixture is 3 0 minutes, while potlife is 2 hours. For vertical surfaces such as firewalls, apply two to three coats of Plexibond mixture by textured roller (for orange peel texture finish) or three to five coats by brush (for plain finish) while maintaining coverage rate at 5-6 sq. meters per gallon. Recoating interval is 1-2 hours. For horizontal surfaces such as roof decks, parapets, canopies and ledges, apply three to five coats by brush or two to three coats by textured roller. Reinforce ts, corners and active cracks susceptible to structural cracking or movement with a strip of fibergloss matting. Put on the motting immediately after the second coat, while the mixture is still wet. The motting should adhere to the mixture. Make sure the Plexibond coating and the matting is completely dry before applying succeeding coats. The motting should be completely covered by the mixture. Let dry for one day, then apply a bond coat by brushing Boysen Plexibond straight from the can prior to laying out mortar topping. For filling large cracks, add 3 parts by volume of fine uniform-sized sand to 1 part cement and mix with Plexibond to trowellable consistency. For maximum durability, topcoat application is recommended. Suggested topcoats are Boysen Permacoat Latex, Boysen Acrytex, Boysen Poly-U 2K Point, Boysen Acqua Epoxy or Boysen Epoxy Enamel. Allow Plexibond to dry at least one day before paint application.

Table of Contents

ENAMEL PAINT

Table of Contents

Boysen Flat Wall Enamel #800 DESCRIPTION: Boysen Flat Wall Enamel #BOO is a flat alkyd type paint that provides great durability while being noted as a fast drying paint. It is formulated to give a tough, durable, beautiful and high build film on wood and metal. Because of its superior hiding, it also can be used as a primer for enamel coatings. Levels evenly, showing no lap and brush marks when applied skillfully.

.

PRINCIPAL USES: For interior wood and metal surfaces. PRACTICAL COVERAGE DRY FILM THICKNESS SURFACE DRY DRY THROUGH OVERCOATING INTERVAL THINNING APPLICATION COLORANT PACKAGING

20 - 25 sq.m.14 liters/coat 1.5 mils/coat Thidy (30) minutes Eight (8) hours Allow six (6) hours before recoat Use Boysen Paint Thinner It can be applied easily by brush, roller or conventional spray Whites may be tinted to pastel/light shades of desired color using Boysen Oil Tinting Colors. 16-liter, 4-liter and 1 I't I er cans

-

SURFACE PREPARATION

-

Wood Surface to be painted should be clean and dry, free from dust, dirt and other foreign matter. Hammer all nails deep enough to apply putty. Sand rough wood until smooth, then dust off before painting. If repainting, first remove all blistering, peeling and scaling paint by wire brushing or Boysen Paint and Varnish Remover #141, then prime with Boysen Flatwall Enamel #800 before recoating.

-

Metal Wipe the surface with rag soaked in paint thinner to remove dust, dirt, grease, oil, wax and other foreign matter. For new G.I. sheets, etch the surface by applying 10% Boysen Metal Etching Solution #71 (dilute 1 part of 8-71 to 9 parts water). If repainting, wire brush or scrape rusted metals and apply Boysen Metal Etching Solution #71 to remove all rust. Let it stay for 10-15 minutes. Be sure to wash off surface thoroughly with water, letting it dry before applying paint. Primer should be applied a few hours after application of B-71 before rust set in. PAINTING SCHEDULE WOOD 1 st Coat putty 2nd & 3rd Coat

Boysen Flatwall Enamel #800 Boysen Plasolux Glazing Putty #311 Boysen Flatwall Enamel #BOO

Table of Contents

METAL 1st Coat puny 2nd & 3rd Coat

Boysen Metal Primer Red Lead #370, Zinc Chromate #320, or Red Oxide #310 Boysen Plasolux Glazing Putty #31 1 Boysen Flatwall Enamel #800

Table of Contents

Boysen Semi-Gloss Enamel #200 DESCRIPTION: Boysen Semi-Gloss Enamel #200 is a n alkyd type paint that provides great durability while being noted as a fast drying paint. It is formulated to give a tough, durable, beautiful and high build film on wood and metal. Its superior hiding, combined with a semi gloss finish, makes it easier to clean and resists wear and abrasion. PRINCIPAL USES: For interior wood and metal surfaces. PRACTICAL COVERAGE DRY FILM THICKNESS SURFACE DRY DRY THROUGH OVERCOATING INTERVAL THINNING APPLICATION COLORANT PACKAGING

20 - 25 sq.m./4 liters/coat 1.5 mils/coat Thirty (30) minutes Ten (10) hours Allow six (6) hours before recoat Use Boysen Paint Thinner if necessary By brush, roller or conventional spray Whites may be tinted to pastel/light shades of desired color using Boysen Oil Tinting Color 16-liter, 4-liter cans

SURFACE PREPARATION Wood - Surface to be painted should be clean and dry, free from dust, dirt and other foreign matter. Hammer all nails deep enough to apply putty. Sand rough wood until smooth, then dust off before painting. If repainting, first remove all blistering, peeling and scaling paint by wire brushing or Boysen Paint and Varnish Remover #141, then prime with Boysen Flatwall Enamel #BOO before recoating. Metal - Wipe the surface with rag soaked in paint thinner to remove dust, dirt, grease, oil, wax and other foreign matter. For new G.I. sheets, etch the surface by applying 10% Boysen Metal Etching Solution #71 (dilute 1 part of B-71 to 9 parts water). If repainting, wire brush or scrape rusted metals and apply Boysen Metal Etching Solution #71 to remove all rust. Let it stay for 10-15 minutes. Be sure to wash off surface thoroughly with water, letting it dry before applying paint. Primer should be applied a few hours after application of B-71 before rust set in. PAINTING SCHEDULE WOOD 1st coat PuW 2nd & 3rd coat

Boysen Flatwall Enamel #BOO Boysen Plasolux Glazing Putty #31 1 Boysen Semi-Gloss Enamel #200

Table of Contents

Metal 1st coat 2nd & 3rd coat

Boysen Metal Primer Red Lead #370, Zinc Chromate #320, or Red Oxide #3 1 0 Boysen Semi-Gloss Enamel #200

Table of Contents

Boysen Quick Drying Enamel DESCRIPTION: Boysen Quick Drying Enamel is an alkyd type paint that provides great durability while being noted as a fast drying paint. It is formulated to give a tough, durable, beautiful and high build film on wood and metal. Its superior hiding, combined with an exceptionally high gloss level, leads to an excellent, long-lasting finished appearance. PRINCIPAL USES: Superior for exterior and interior wood and metal surfaces. PRACTICAL COVERAGE DRY FILM THICKNESS SURFACE DRY DRY THROUGH OVERCOATING INTERVAL THINNING APPLICATION PACKAGING

20 - 25 sq.m./4 liters/coat 1.5 mildcoat Five (5) hours maximum Two (2) hours Allow eight (8) hours before recoat use Boysen Paint Thinner if necessary It can be applied easily by brush, roller or conventional spray 16-liter (white only), 4-liter and 1-liter cans

AVAILABLE COLORS: 0600 8621 0630 8632 B640 B642 B647 B650 B651 B656 8658 8661

White Ivory Silver Gray Medium Gray Royal Blue Sky Blue Delft Blue Nile Green Dark Green Jade Green Emerald Green Lemon Yellow

Caterpillar Yellow Bright Red International Red Maroon Orange Chocolate Brown Mahogany Sammy Brown (Analux Yellowish) Black Flat Block

COLORANT: Whites may be tinted to pastel/light shades of desired color using Boysen Oil Tinting Colors. SURFACE PREPARATION Wood - Surface to be pointed should be clean and dry, free from dust, dirt and other foreign matter. Hammer all nails deep enough to apply putty. Sand rough wood until smooth, then dust off before painting. If repainting, first remove all blistering, peeling and scaling paint by wire brushing or Boysen Paint and Varnish Remover #141, then prime with Boysen Flatwall Enamel #800 before recoating. 47

Table of Contents

-

Metal Wipe the surface with rag soaked in paint thinner to remove dust, dirt, grease, oil, wax and other foreign matter. For new G.I. sheets, etch the surface by applying 10% Boysen Metal Etching Solution #71 (dilute 1 part of 6-71 to 9 parts water). If repainting, wire brush or scrape rusted metals and apply Boysen Metal Etching Solution #71 to remove all rust. Let it stay for 10-15 minutes. Be sure to wash off surface thoroughly with woter, letting it dry before applying paint. Prime immediately after drying. PAINTING SCHEDULE WOOD 1st Coat putty 2nd & 3rd Coat

METAL 1st Coat putty 2nd & 3rd Coat

Boysen Flatwall Enamel #800 Boysen Plasolux Glazing Putty #311 Boysen Quick Dry Enamel (any desired color)

Boysen Metal Primer Red Lead #370, Zinc Chromate #320, or Red Oxide #310 Boysen Plasolux Glazing Putty #311 Boysen Quick Dry Enamel (any desired color)

Table of Contents

Boysen Schoolboard Slating Paint, Green #655 DESCRIPTION: Boysen Schootboard Slating Paint #655 is an alkyd based point that dries to a flat finish for classroom blackboards, bulletin boards and similar flat surfaces intended for chalk markings. PRINCIPAL USES: For metal or wood surfaces. PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION PACKAGING

25-30 sq. m. / gallon /coat 2-4 hours Overnight 1.5 mils/coat Allow overnight before recoating Boysen Paint Thinner by brush, roller or spray 4-liter and 1-liter cans

SURFACE PREPARATION New wood Surface to be painted should be clean ond dry, free from dust, dirt and other foreign matter. Hammer all nails deep enough to apply putty. Sand rough wood until smooth, them dust off before painting. Repainting For surfaces previously painted with alkyd, latex or solvent based epoxy coatings, scrape off loosely adhering paint, remove oil and grease by detergent cleaning, then scuff sand.

PAINTING SCHEDULE Wood or Metal 1st Coat putty Topcoat

Boysen Plasolux Primer Surfacer #307 Boysen Plasolux Glozing Putty #31 1 Boysen Schoolboard Slating Paint #655

Table of Contents

Boysen Plasolux Glazing Putty #311 DESCRIPTION: Boysen Plasolux Glazing Putty #311 is an alkyd-type product specially prepared for filling minor surface unevenness. PRINCIPAL USES: For filling minor surface dents and imperfections on wood. PRACTICAL COVERAGE SURFACE DRY DRY THROUGH OVERCOATING INTERVAL THINNING APPLICATION PACKAGING

Full Putty - 10-12 sq. m. /gallon / coat Spot putty 25 sq. m. / gallon / coat 4-5 hours Overnight Allow two hours before recoating Boysen Paint Thinner if necessary putty knife 4-liter and 1-liter cans

-

:

PAINTING SCHEDULE Wood or Metal 1st Coat putty 2nd & 3rd coat

Boysen Flahvall Enamel White #800 or Boysen Plasolux Primer Surfacer #307 Boysen Plasolux Glazing Putty #311 Boysen Quick Drying Enamel (any desired color) Boysen Semi-Gloss Enamel #200

Table of Contents

Boysen Plasolux Primer Surfacer #307 DESCRIPTION: Boysen Plasolux Primer Surfacer #307 is a n alkyd-type paint formulated to provide depth build for final coats of Boysen Quick Dry Enamel. PRINCIPAL USES: As primer surfacer for exterior and interior surfaces of wood or metal. PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION PACKAGING

25-30 sq. m. /gallon / coat 2 hours Overnight 1.5mils/coat Allow one hour before recoating Boysen Paint Thinner if necessary by brush or spray 4-liter and 1-liter cans

SURFACE PREPARATION For surfaces previously painted with alkyd, latex or solvent based epoxy coatings, scrape off loosely adhering paint, remove oil and grease by detergent cleaning, then scuff sand. PAINTING SCHEDULE Wood or Metal 1st Coat puw Topcoat

Boysen Plasolux Primer Surfacer #307 Boysen Plasolux Glazing Putty #311 Boysen Quick Drying Enamel (any desired color) Boysen Semi-Gloss Enamel #200

Table of Contents

Boysen Red Oxide Primer #310 DESCRIPTION: Boysen Red Oxide Primer #310 is a rust inhibiting primer for steel and iron surfaces. It is particularly good for metal shops who deliver metal products coated with a shop primer to protect them from rust corrosion until such time as they are finished with desired topcoat. PRINCIPAL USES: As a primer for exterior and interior steel. PRACTICAL COVERAGE

DRY FltM THICKNESS SURFACE DRY DRY THROUGH OVERCOATING INTERVAL THINNING APPLICATION PACKAGING

-

25 30 sq.m./4 lifers/coat 1.5 mildcoat Two hours 5-6 hours 8 hours to overnight use Boysen Paint Thinner if necessary brush, roller or conventional spray 16-liter, 4-liter and 1-liter cons

SURFACE PREPARATION Wipe the metal surface with rag soaked in point thinner to remove dust, dirt, grease, oil, wax and other foreign matter. For new G.I. sheets, etch the surface by applying 10% Boysen Metal Etching Solution #71 (dilute 1 part of B-71 to 9 parts water). If repainting, wire brush or scrape rusted metals and apply Boysen Metal Etching Solution #71 to remove all rust. Let it stay for 10-15 minutes. Be sure to wash off surface thoroughly with water, letting it dry before applying paint. Prime immediately after drying. PAINTING SCHEDULE METAL 1st Coat putty 2nd & 3rd Coat

Boysen Metal Primer Red Oxide #310 Boysen Plasolux Glozing Putty #311 if necessary Boysen Quick Dry Enamel (ony desired color)

Table of Contents

Boysen Zinc Chromate Yellow Metal Primer #320 DESCRIPTION: Boysen Metal Primer Zinc Chromate Yellow #320 is a rust inhibiting primer with good adhesion to structural steel, fabricated iron, and on any ferrous metal. PRINCIPAL USES: Ideally applied on exterior and interior galvanized metals. PRACTICAL COVERAGE DRY FILM THICKNESS SURFACE DRY DRY THROUGH OVERCOATING INTERVAL THINNING APPLICATION PACKAGING

25 - 30 sq.m./4 liters/coat 1.5 mils/coat Two hours 5-6 hours Allow overnight before recoat use Boysen Paint Thinner if necessary It can be applied easily by brush, roller or conventional spray 4-liter cans

SURFACE PREPARATION Wipe the metal surface with rag soaked in paint thinner to remove dust, dirt, grease, oil, wax and other foreign mafer. For new G.I. sheets, etch the surface by applying 10% Boysen Metal Etching Solution #71 (dilute 1 part of B-71 to 9 parts water). If repainting, wire brush or scrape rusted metals and apply Boysen Metal Etching Solution #71 to remove all rust. Let it stay for 10-15 minutes. Be sure to wash off surface thoroughly with water, letting it dry before applying paint. Prime immediately after drying. PAINTING SCHEDULE METAL 1st Coat putty 2nd & 3rd Coat

Boysen Metal Primer Zinc Chromate Yellow #320 Boysen Plasolux Glazing Putty #311 Boysen Quick Dry Enamel #600 (any desired color)

Table of Contents

Boysen Red Lead Primer #370 DESCRIPTION: Boysen Red Lead Primer #370 is a high grade, wst inhibiting primer for steel and iron surfaces. This produd contains a high percentage of red lead, ground in.a top quality vehicle to make it a suitable foundation for enamel topcoat. PRINCIPAL USES: Primer for ferrous surfaces such as iron and steel frames. PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION PACKAGING

-

25 30 sq.m./4 liters/coat Two hours 5-6 hours 1.5 mils/coat Allow overnight before recoat Use Boysen Paint Thinner It can be applied easily by brush, roller or conventional spray 16-liter, 4-liter and 1-liter cans

SURFACE PREPARATION Wipe the metal surface with rag soaked in paint thinner to remove dust, dirt, grease, oil, wax and other foreign matter. For new G.I. sheets, etch the surface by applying 10% Boysen Metal Etching Solution #71 (dilute 1 part of 8-71 to 9 parts water). If repainting, wire brush or scrape rusted metals and apply Boysen Metal Etching Solution #71 to remove all rust. Let it stay for 10-15 minutes. Be sure to wash off surface thoroughly with water, letting it dry before applying point. Prime immediately after drying

PAINTING SCHEDULE METAL 1st Coat puthl 2nd & 3rd Coat

:

Boysen Red Lead Primer #370 Boysen Plasolux Glazing Puth/ #311 Boysen Quick Dry Enamel #600 (any desired color)

Table of Contents

Boysen Aquaseal #99 DESCRIPTION: Boysen Aquaseal #99 is a non silicone protective sealer designed to impart maximum water repellancy to a wide variety of above ground masonry surfaces. It minimizes unsightly efflorescence and reduces cracking and spalling. Boysen Aquaseal #99 extends the life and natural appearance of surfaces. PRINCIPAL USES: Functions as a clear penetrating sealer on porous substrates to repel water and moisture for brick, stucco, concrete, hollow blocks, rubble, and sandblast finish. PRACTICAL COVERAGE DRY THROUGH APPLICATION THINNING PACKAGING

8 sq.m. / gallon 2 hours by brush (do not spray) Nbt necessary. Use paint thinner for washing of tools 4-liter cans

PAINTING SCHEDULE: Boysen Aquaseal #99 should be applied liberally to saturate the surface. Generous overlapping of es is recommended until it drips down about 6 inches on masonry. Note: Resulting treated surfaces cannot be painted over until the coating wears out.

Table of Contents

Boysen Silver Finish Aluminum Paint #75 DESCRIPTION: Boysen Silver Finish Aluminum Paint #75 is a ready mixed aluminum paint for general use on industrial and decorative work, for maximum wear. PRINCIPAL USES: For exferior and interior metal. PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL APPLICATION THINNING PACKAGING

25-30 sqm. / gallon /coat 2 -4 hours Overnight 1.5 mils/coat Allow overnight before recoating by brush not necessary 4-liter and 1-liter cans

PAINTING SCHEDULE: New Metal (ferrous) 1st Coat 2nd & 3rd Coot

Boysen Red Lead Primer #370 Boysen Silver Finish Aluminum Paint #75

New Metal (non-ferrous) 1st Coat 2nd & 3rd Coat

Boysen Zinc Chromate .Primer Yellow #320 Boysen Silver Finish Aluminum Paint #75

Table of Contents

Boysen Heat Resisting Aluminum Paint #95 DESCRIPTION: Boysen Heat Resisting Aluminum #95 is formulated for surfaces subject to heat with peak temperature of 800°F or 427°C. PRINCIPAL USES: For metal surfaces of equipment, radiators and machinery. PRACTICAL COVERAGE DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL APPLICATION THINNING PACKAGING

:

20 sq.m. / gallon /coat Will dry when peak temperature is reached. 1.5-2 mils Allow overnight before recoating by brush not necessary 4-liter cans

SURFACE PREPARATION Metal Wipe the surface with rag soaked in lacquer thinner to remove dust, dirt, grease, oil, wax and other foreign matter. For rusted portions, wire brush or scrape loose rust and apply Boysen Metal Etching Solution #71. Let it stay for 10-15 minutes. Be sure to wash off surface thoroughly with water or paint thinner, letting it dry before applying paint. PAINTING SCHEDULE Apply 2 to 3 coots of Boysen Heat Resisting Aluminum #95 on bare substrate.

Table of Contents

Boysen Heat Resisting Aluminum #83 DESCRIPTION: Boysen Heat Resisting Aluminum #83 is formulated for surfaces subject to heat with peak temperature of 200°F or 93.3"C. PRINCIPAL USES: For metal surfaces of pipes, smoke stacks and ventilators. PRACTICAL COVERAGE DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL APPLICATION THINNING PACKAGING

:

20 sq.m. / gallon / coat Will dry when peak temperature is reached. 1.5-2 mils Allow overnight before recoating by brush not necessary 4-liter cans

SURFACE PREPARATION Metal Wipe the surface with rag soaked in lacquer thinner to remove dust, dirt, grease, oil, wax and other foreign matter. For rusted portions, wire brush or scrape loose rust and apply Boysen Metal Etching Solution #71. Let it stay for 10-15 minutes. Be sure to wash off surface thoroughly with water or point thinner, letting it dry before applying paint.

PAINTING SCHEDULE: Apply 2 to 3 coats of Boysen Heat Resisting Aluminum #83 on bare substrate

Table of Contents

Boysen Bridge and Tank Aluminum Paint #85 DESCRIPTION: Boysen Bridge and Tank Aluminum Paint # 85 is a highly reflective grade of aluminum paint ideal for storage tanks and structural steel, since it tends to keep these cooler. PRINCIPAL USES: For storage tanks, structural steel and other industrial metal surfaces. PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION PACKAGING

20-25 sq. m. / gallon / coat 2-4 hours Overnight 1.5 mils Allow 24 hours before recoating Not necessary By brush 4-liter cans

SURFACE PREPARATION Metal Wipe the surface with rag soaked in paint thinner to remove dust, dirt, grease, oil, wax and other foreign matter. For new G.I. sheets, etch the surface by applying 10% Boysen Metal Etching Solution #71 (dilute 1 part of B-71 to 9 parts water). If repainting, wire brush or scrape rusted metals and apply Boysen Metal Etching Solution #71. Let it stay for 10-15 minutes. Be sure to wash off surface thoroughly with water or paint thinner, letting it dry before applying paint. Primer should be applied immediately after treatment to prevent flash rusting. PAINTING SCHEDULE: New metal (ferrous) 1st coat 2nd and 3rd coat

Boysen Red Lead Primer #370 Boysen Bridge and Tank Aluminum Paint # 85

New metal (non-ferrous) 1st coat 2nd and 3rd coat

Boysen Zinc Chromate Primer Yellow # 320 Boysen Bridge and Tank Aluminum Paint # 85

Table of Contents

Boysen Reflectorized Traffic Paint DESCRIPTION: Boysen Reflectorized Traffic Paint is an alkyd-type paint specially developed to resist the rigorous environment encountered on highways ond related surfaces such as airfields and parking lots. It is a fast drying solvent-based marking paint which forms a hard durable film that offers good wear resistance and better reflective beads retention. PRINCIPAL USES: As a durable alternative to solvent-based alkyd traffic paint for use on highway markings, airfields and parking lot linings. PRACTICAL COVERAGE SURFACE DRY DRY THROUGH OVERCOATING INTERVAL THINNING APPLICATION PACKAGING

:

20 sq. m./ gallon /coat 10 minutes 30 minutes 30 mins. Boysen Point Thinner if necessary By brush 4-liter cans

AVAILABLE COLORS: Boysen Reflectorized Traffic Paint #19-101 White Boysen Reflectorized Traffic Paint #19-161 Yellow PAINTING SCHEDULE 1st coat 2nd coat 8 3rd coat

:

Boysen Epoxy Primer White #2200 Boysen ReflectorizedTraffic Paint (of desired color)

Table of Contents

Boysen Alkyd Traffic Paint DESCRIPTION: Boysen Alkyd Traffic Paint is a quick drying alkyd based marking paint with excellent adhesion and durability. It maybe used alone as a non-reflectorized marking. It can be applied on epoxy-primed asphalt and rough concrete. PRINCIPAL USES: It is designed for use on street markings, curbs and other areas where traffic lanes and safety zones ore marked. PRACTICAL COVERAGE SURFACE DRY DRY THROUGH OVERCOATING INTERVAL THINNING APPLICATION PACKAGING

:

20-25 sq. m.1 gallon I coat 30 minutes 1 hour 1 hour Boysen Paint Thinner if needed By brush 4-liter cans

AVAILABLE COLORS: Boysen Alkyd Traffic Paint #I901 White Boysen Alkyd Traffic Paint #I961 Yellow PAINTING SCHEDULE Primer 2nd and 3rd coat

:

Boysen Epoxy Primer White #2200 Boysen Alkyd Traffic Paint (of desired color)

Table of Contents

STAINS

Table of Contents

Boysen Xyladecor DESCRIPTION: Boysen Xyladecor is a solvent based, deep penetrating type of stain that combines decorative, water repellent and wood preserving properties in one and dries to a silk matte finish. It emphasizes the grain, bringing out the natural beauty in any kind of wood. PRINCIPAL USES: Boysen Xyladecor is the wood shin available that could be used for exterior and interior wood surfaces. It is the best way to protect your wood since it seals, prevents fungal growth, mold and insect attacks through its preservative contents.

-

PRACTICAL COVERAGE SURFACE DRY DRY THROUGH OVERCOATING INTERVAL THINNING APPLICATION PACKAGING

:

20 25 sq.m./gal./coot (may vary depending on wood absorptivity) Thirty (30) minutes Overnight 30 minutes, depending on weather and absorption rate Not necessary by brush, spray or by dipping 4-liter cans

AVAllABLE COLORS X-101 Colorless X-102 Pine X-103 Teak X-105 Chestnut X-107 Mahogany SURFACE PREPARATION Sand surface until wood is smooth to the touch and no slivers or rough edges remain. Hammer all nails deep enough to apply putty. Dust off surfaces completely then wipe with a clean rag. If repainting, remove all paint by wire brushing, scraping, or by using Boysen Paint & Varnish Remover #141. PAINTING SCHEDULE Thoroughly shake the can before opening. Apply Boysen Xyladecor direct to base wood without primers or undercoats either by brush, spray or by dipping in an open trough or tank to achieve total covering rate. Shake and stir Xyladecor often during use. By Brush: Apply at least 3 fufl brush coats, laying the paint into the wood rather than brushing out. Leave each coat for about thirty (30) minutes, depending on the weather ond the absorption rate. Lightly brush or wipe over once along the grain to remove excess material and to smooth out any runs.

65

Table of Contents

By Spray: Use a coarse nozzle (about 1-5 mm) giving a steam of material rather than a fine atomizing type paint spray. Working pressure should be approximately 44 lbs. / m2. Spraying is not recommended for planed surfaces. By dipping: Dip the timber in Boysen Xyladecor for 2 minutes, varying the time required according to the absorbency of the wood. Stand the timber on end and allow to drain. If necessary, lightly brush the surface once in the direction of the grain before if dries.

Nate: If a very even color finish is desired on wood with varying degrees of absorbency, apply Boysen Xylodecor Colorless first before applying colored varieties of Xyladecor. Boysen Xyladecor Colorless is not recommended for exterior use on its own.

Table of Contents

Boysen Oil Wood Stain DESCRIPTION: Boysen Oil Wood Stain is available in various shades to bring out a clear and natural tone in wood. When clear coated with Boysen Lacquer varnish products, Boysen Oil Wood Stain highlights wood grains, adds freshness and color, and provides superior protection. PRINCIPAL USES: For enhancing wood groin on interior wood works and other surfaces such os cabinets, furniture, ing, etc. PRACTICAL COVERAGE APPLICATION SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING PACKAGING

-

25 30 sqm. /gal. /coat (depending on wood absorptivity) by brush or spray Two (2) hours 4-5 hours 1.5 mils / coat Overnight Boysen Paint Thinner 4-liter and 1-liter cans

AVAILABILITY B2700 Walnut B2705 Maple B2707 Mahogany 82708 Oak 82709 Dark Oak SURFACE PREPARATION Sand sutface until wood is smooth to the touch and no slivers or rough edges remain. Hammer all nails deep enough to apply putty. Dust off surfoces completely then wipe with a clean rag. If repainting, remove all paint by wire brushing, scraping, or by using Boysen Paint & Varnish Remover #141. PAINTING SCHEDULE Thoroughly stir the can contents before using. Apply Boysen Oil Wood Stain direct to bare wood without primers or undercoats either by brush, spray or by dipping in an open trough or tank. Lightly brush or wipe over once along the grain to remove excess material and to smooth out any runs. Leave each coat for about four to eight hours, or until totally dry. Recoat for a darker shade. New Wood

1st coat 2nd coat and 3rd coats 4th and 5th coats

Boysen Oil Wood Stain (any desired color) Boysen Lacquer Sanding Sealer # I 2 5 4 Boysen Clear Gloss Lacquer # I 2 5 0

Table of Contents

LACQUER PAINTS

Table of Contents

Boysen Lacquer Primer Surfacer #305 DESCRIPTION: Boysen Lacquer Primer Surfacer #305 is a lacquer type sealer with very good holdout properties that provide firm foundation for the desired topcoat.

PRINCIPAL USES: As primer for indoor wood surfaces PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION PACKAGING

25-30 sq, m. /gallon / coat Ten minutes Thidy minutes 1.5 mils/coat Allow thirty minutes before recoating Boysen Lacquer Thinner by brush or spray 4-liter and 1-liter cans

PAINTING SCHEDULE:

New metal and wood surfaces: 1st coat 2nd coat 3rd coat Final coat

:

Boysen Lacquer Primer Surfacer #305 Boysen Lacquer Spot Putty #306 Boysen Lacquer Primer Surfacer #305 Boysen Automotive Lacquer # I 3 0 0 or Boysen Gloss Lacquer Enamel # I 2 0 0 in required coats

Repainting Old finish in bad condition should be stripped. Boysen Paint and Varnish Remover # I 4 1 can be used to totally remove the finish. Follow procedure of New Surface. If old lacquer finish is in good condition, sand surface

Table of Contents

Boysen Lacquer Spot Putty #306 DESCRIPTION: Boysen Lacquer Spot Putty #306 is a high quality lacquer type putty for wood specially formulated for easy application and sanding. PRINCIPAL USES: For interior wood surfaces PRACTICAL COVERAGE SURFACE DRY DRY THROUGH OVERCOATING INTERVAL APPLICATION THINNING

Spot putty - 25 sq.m. / gallon Full putty 12 sq. m. / gallon 5-10 minutes One (1) hour Recoat after 30 minutes Putty knife Apply as is. If necessary, use Boysen Lacquer Thinner 4-liter and 1-liter cans

-

:

PACKAGING

PAINTING SCHEDULE:

New metal and wood surfaces:

1st coat 2nd coat 3rd coat Final coat

:

Boysen Lacquer Primer Surfacer #305 Boysen Lacquer Spot Putty #306 Boysen Lacquer Primer Surfacer #305 Boysen Automotive Lacquer # I 3 0 0 or Boysen Gloss Lacquer Enamel #I200 in required coats

Repainting Old finish in bad condition should be stripped. Boysen Paint and Varnish Remover # I 4 1 can be used to totally remove the finish.

If old lacquer finish is in good condition, sand surface. Make sure to clean and dry before coating with Boysen Automotive Lacquer #1300.

Table of Contents

Boysen Gloss Lacquer Enamel #I200 DESCRIPTION: Boysen Gloss Lacquer Enamel # I 2 0 0 is a high-grade pigmented lacquer topcoat that flows evenly and dries fast. It is highly recommended for industrial, residential, commercial usage and product finishing. PRINCIPAL USES: A durable finish for wood and metal surfaces not directly exposed to weathering. PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL APPLICATION THINNING PACKAGING

25-30 sqm. / gallon /coat 10 minutes Thirty minutes 1.5 mils / coat Recoat after 30 minutes by spray or brush Boysen Lacquer Thinner 4-liter and 1-liter cans

PAINTING SCHEDULE: New metal and wood surfaces: 1st coat 2nd coat 3rd coat Final coat

:

Boysen Locquer Primer Surfocer #305 Boysen Lacquer Spot Putty #306 Boysen Lacquer Primer Surfacer #305 Boysen Gloss Lacquer Enomel # I 2 0 0 in required coats

Repainting Old finish in bod condition should be stripped. Boysen Paint ond Varnish Remover # I 4 1 can be used to totally remove the finish. If old lacquer finish is i n good condition, sand surface. Make sure to clean and dry before coating Boysen Gloss Lacquer Enamel #1200.

Table of Contents

Boysen Clear Gloss Lacquer #I250 DESCRIPTION: Boysen Clear Gloss Lacquer that dries to a hard durable film.

#I250 is a high solid, gloss lacquer varnish finish

PRINCIPAL USES: For interior sealed wood such as furniture, store fixtures, cabinets, doors and s. PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL APPLICATION THINNING PACKAGING

25-30sq. m. / gallon /coat 10 minutes 1 hour

1.5 mils /coat Recoat after 30 minutes By brush or spray Boysen Lacquer Thinner #50 16-liter, 4-liter and 1 -liter cans

PAINTING SCHEDULE:

New wood surfaces: Sealer Coat

:

Final coat

:

Boysen Lacquer Sanding Sealer #1254, sand lightly before topcoat application Boysen Clear Gloss Lacquer #I250

Repainting Old finish in bad condition should be stripped. Boysen Paint and Varnish Remover #I41 can be used to totally remove the finish. If old lacquer finish is in good condition, sand surface. Make sure to clean and dry before coating Boysen Clear Gloss Lacquer #1250.

Table of Contents

Boysen Clear Dead Flat Lacquer #I253 DESCRIPTION: Boysen Clear Dead Flat Lacquer #I253 is o high solid, flat lacquer varnish finish that dries to a hard durable film. Its high build properties make it superior on furniture, fixtures or other woodworks. PRINCIPAL USES: For interior sealed wood such as furniture, store fixtures, cabinets, doors and s. PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL APPLICATION THINNING PACKAGING

25-30 sq. m. /gallon / coat 10 minutes 1 hour 1.5 mils / coat Recoat after 30 minutes By spray or brush Boysen Lacquer Thinner #50 16-liter, 4-liter and 1-liter cans

PAINTING SCHEDULE: New wood surfaces: : Sealer coat : Final coat

Boysen Lacquer Sanding Sealer # I 2 5 4 Boysen Clear Dead Flat Lacquer #I253

Repainting Old finish in bad condition should be stripped. Boysen Paint and Varnish Remover # I 4 1 can be used to totally remove the finish. If old lacquer finish is in good condition, sand surface. Make sure to clean and dry before coating the required coats of Boysen Clear Deod Flat Lacquer #1253.

Table of Contents

Boysen Lacquer Sanding Sealer #I254 DESCRIPTION: Boysen Lacquer Sanding Sealer # I 2 5 4 is a commercial grade sealer for wood before finishing with either gloss or flat lacquer. It has good sealing and hold out properties, and require less sanding. PRINCIPAL USES: For interior sealed wood such as furniture, store fixtures, cabinets, doors and s. PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL APPLICATION THINNING PACKAGING

25-30 sq. rn. /gallon /coat 10 minutes 1 hour 1.5 mils / coat Recoat.after 30 minutes By brush or spray Boysen Lacquer Thinner #50 16-liter, 4-liter and 1-liter cans

PAINTING SCHEDULE: New wood surfaces: Sealer coat Final coat

:

:

Boysen Lacquer Sanding Sealer #I254 Boysen Clear Gloss Lacquer # I 2 5 0 or Boysen Clear Dead Flat Lacquer #I253

Repainting Old finish in bad condition should be stripped. Boysen Point and Varnish Remover # I 4 1 can be used to totally remove the finish.

If old lacquer finish is in good condition, sand surface. Make sure to clean and dry before coating.

Table of Contents

Boysen Water White Clear Gloss Lacquer #I258 DESCRIPTION: Boysen Water White Clear Gloss Lacquer #I258 is the highest grade clear gloss lacquer finish for a durable finishing for interior woodwork. Its properties enhance the natural grain of wood. PRINCIPAL USES: For lacquer finishing of interior wood walls, furniture, store fixtures, cabinets, doors and s. PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL APPLICATION THINNING PACKAGING

25-30sq.m. / gallon / coat 10 minutes 1 hour 1.5 mils / coat Recoat after 30 minutes By brush or spray Boysen Lacquer Thinner #50 4-liter cans

PAINTING SCHEDULE Sealer coat Final coat

: :

Boysen Lacquer Sanding Sealer #I254 Boysen Water White Clear Gloss Lacquer #I258

Repainting Old lacquer finish in bad condition should be stripped. Prepare to clean and dry before finishing as indicated for new wood. If old lacquer finish is in good condition, sand and dust surface. Apply required finish coats of Boysen Water White Cleor Gloss Lacquer #1258.

Table of Contents

Boysen Automotive Lacquer #I300 DESCRIPTION: Boysen Automotive Lacquer is a lacquer type paint that is easy to apply, dries rapidly to a long-wearing attractive finish. PRINCIPAL USES: For indoor wood surfaces such as doors, iams, cabinets and shelves. PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL APPLICATION THINNING PACKAGING

25-30 sqm. /gallon / coat 10 minutes 30 minutes 1.5 mils / coat 1 hour By spray or brush Boysen Lacquer Thinner #50 4-liter and 1-liter cans

SURFACE PREPARATION

-

Wood Surfoce to be painted should be clean and dry, free from dust, dirt and other foreign matter. Hammer all nails deep enough to apply putty. Sand rough wood until smooth, then dust off before painting.

If repainting, first remove all blistering, peeling and scaling paint by wire brushing or Boysen Paint and Varnish Remover #14l, then prime before recoating. PAINTING SCHEDULE: New metal and wood surfaces: 1st coat puth/ 2nd coat Final coat

:

Boysen Lacquer Primer Surfacer #305 Boysen Lacquer Spot Putty #306 if required Boysen Lacquer Primer Surfacer #305 on puttied oreas Boysen Automotive Lacquer # I 3 0 0 in required coots

Repainting Old finish in bad condition should be stripped. Boysen Point and Varnish Remover # I 4 1 can be used to totally remove the finish.

If old lacquer finish is in good condition, sand surface. Make sure to clean and dry before coating Boysen Automotive Lacquer #1300.

Table of Contents

ACRYLIC SOLVENT BASED PAINTS

Table of Contents

Boysen Acrytex Clear Coat #I 700 DESCRIPTION: Boysen Acrytex Clear Coat #I700 is an acrylic solvent-based coating that has excellent adhesion, long term durability and easy cleanup characteristics. Creates superior sheen and maximum protection for Multifleck coated finishes. PRINCIPAL USES: As a clear coat protection for new and Acrytex painted masonry. Can also be used for wood. PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION PACKAGING

25 - 30 sq.m./coat/gal. Thirty (30)minutes Two (2)hours 1.5 mils/coat Two (2) hours Use Boysen Acrytex Reducer #I705 only by brush, roller or spray 4-liter cans

PAINTING APPLICATION Apply 2 to 3 coats of Boysen Acrytex Clear #I700 on bare pebble washout or natural stone finished wall by spray or brush. For walls with Boysen Multifleck, apply a thin coat by spray if gloss finish is desired.

Table of Contents

Boysen Acrytex DESCRIPTION: Boysen Acrytex is an acrylic solvent-based coating that forms a seamless, nonporous, watertight film that repels water and prevents seepage. It is noted for its excellent adhesion and long-term durability. Creates a very tight film, serving as a moisture sealant for concrete and a stain inhibitor for wood. PRINCIPAL USES: As a topcoat for new and previously painted exterior and interior masonry, wood and fiber cement boards coated with Acryiex Primer #1705. PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING COLORANTS PACKAGING AVAILABILITY

--

textured finish 15 -1 8 sq.m./coat/gal. plain finish -- 25-30 sq.m./coat/gal. Thirty (30) minutes Two (2) hours 1.5 mils/coat Two (2) hours Boysen Acrytex Reducer # I 7 0 5 Boysen Acryiex Tinting Colors 4-liter and 16-liter cans Boysen Acrytex Flat #1701, Boysen Acrytex Semi-Gloss #1715, Boysen Acrytex Gloss #I 710

SURFACE PREPARATION (Masonty) Allow new masonry to dry for 14 to 28 days under normal weather conditions before painting. No need to treat new masonry with Boysen Masonry Neutralizer #44. Surface to be painted should be clean and dry, free from oil, grease, dust, dirt, contaminants and all loose grit and mortar. Repainting For surfaces previously painted with latex, enamel or lacquer coatings, scrape to bore substrate and clean surface thoroughly, then follow schedule for new painting. PAINTING SCHEDULE: Plain Finish 1. Prime surface with Boysen Acrylex Primer #1705. 2. Fill hairline cracks and minor surface imperfections with Boysen Acrytex Cast # I 7 1 1 using a putty knife. 3. Apply 1-2 coots of Boysen Acrytex Topcoat of desired sheen by brush, roller or spray. Textured Finish 1. Prime surface with Boysen Acvex Primer #1705. 2. Spray Boysen Acrytex Cast # I 7 1 1 with mortar gun. Press Acrytex Cast with wooden roller 1015 minutes after spraying. (Note: wet wooden roller with Boysen Acrytex Reducer # I 7 5 0 to prevent the roller from sticking to the cast.) 3. Apply 1-2 coats of Boysen Acryiex Topcoat of desired sheen by brush, roller or spray. 82

Table of Contents

Boysen Acrytex Cast #I71 1 DESCRIPTION: Boysen Acrytex Cast #I71 1 is an acrylic solvent-based putty for holes and surface imperfections when a plain finish of Boysen Acrytex Topcoat is desired. Gives an elegant and durable textured finish when applied with a mortar gun. It is water tight thus can repel water and prevent seepage. Noted for excellent adhesion ond long term durability. PRINCIPAL USES: For new and previously painted exterior and interior masonry, wood and fiber cement boards. It also ads as a water repellent. Creates a very tight film, serving as a moisture sealant for concrete and a stain inhibitor for wood. PRACTICAL COVERAGE

As putty -- 10-12 sq.m./coat/gol. As texture -- 5-6 sq.m./coat/gal.

APPLICATION SURFACE DRY DRY THROUGH OVERCOATING INTERVAL THINNING PACKAGING

by mortar gun (texture) or painter's knife (putty) Thirty (30)minutes Two (2) hours Four (4) hours Use Boysen Acrytex Reducer #I705 only 4-liter cans

:

SURFACE PREPARATION Allow new masonry to dry for 14 to 28 days under normal weather conditions before painting. No need to treat new masonry with Boysen Masonry Neutralizer #44. Surface to be painted should be clean ond dry, free from oil, grease, dust, dirt, contaminants and all loose grit and mortar. Repainting For surfaces previously painted with latex, enamel or lacquer coatings, scrape to bare substrate and clean surface thoroughly, then follow schedule for new painting. PAINTING SCHEDULE Plain Finish 1. Prime bare substrate with Boysen Acrytex Primer # 1705. 2. Putty minor surface imperfections with Boysen Acrytex Cast # 171 1. Spot prime puttied areas. 3. Brush on Boysen Acrytex Primer #I705 when a high gloss finish on wood is desired. 4. Finish with two (2) coats of Boysen Acrytex Topcoat to desired sheen and color. Textured Finish 1. Prime bare substrate with Boysen Acrytex Primer # 1705. 2. Spray Boysen Acrytex Cast # 171 1 with mortar gun. Press Acrytex Cast with plain wooden roller 10-15 minutes after spraying. Wet wooden roller with Boysen Acrytex Reducer #I750 to prevent the roller from sticking to the cast. 3. Finish with two (2) coats o f Boysen Acrytex Topcoat t o desired sheen and color.

Table of Contents

Boysen Acrytex Primer #I705 DESCRIPTION: Boysen Acrytex Primer # I 7 0 5 is o concrete sealer for plain or textured Acrytex finishes. It is an acrylic solvent-based coating that forms a seamless, non-porous, watertight film that repels water and prevents seepage. It is noted for its excellent adhesion and long-term durability. PRINCIPAL USES: As a primer for new and previously painted exterior and interior masonry, wood and fiber cement boards. It also acts as a water repellent. Creates a very tight film, sewing as a moisture sealant for concrete and a stain inhibitor for wood. PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS THINNING COLORANTS PACKAGING

25 - 30 sq.m./coat/gal. Thirty (30) minutes Two (2) hours 1.5 mils/coat Boysen Acrytex Reducer #I750 Boysen Arcytex Tinting Colors 4-liter and 16- liter cans

SURFACE PREPARATION New Surface Allow new masonry to dry for 14 to 28 days under normal weather conditions before painting. No need to treat new masonry with Boysen Masonry Neutralizer #44. Surface to be painted should be clean and dry, free from oil, grease, dust, dirt, contaminants and all loose grit and mortar. Repainting For surfaces previously painted with latex, enamel or lacquer coatings, scrape to bare substrate and clean surface thoroughly, then follow schedule for new painting. PAINTING SCHEDULE: Plain Finish 1. Prime surface with Boysen Acrytex Primer #1705. 2. Fill hairline cracks and minor surface imperfections with Boysen Acrytex Cast # I 7 1 1 using putty knife. 3. Brush on Boysen Acrytex Primer # I 7 0 5 when a high gloss finish on wood is desired. 4. Apply 1-2 coats of Boysen Acrytex Topcoat (Flat #1701, Semi-gloss # I 7 1 5 and Gloss #1710) by brush, roller or spray. Textured Finish 1. Prime surface with Boysen Acryiex Primer #1705. 2. Spray Boysen Acrytex Cast # I 7 1 1 with mortar gun. Press Acrytex Cast with wooden roller 1015 minutes after spraying. (Note: wet wooden roller with Boysen Acrytex Reducer # I 7 5 0 to prevent the roller from sticking to the cast.) 3. Apply two (2) coats of Boysen Acrytex Topcoat of desired sheen and color by brush, roller or spray. 84

Table of Contents

EPOXY PAINTS

Table of Contents

Boysen Epoxy Primer DESCRIPTION: Boysen Epoxy Primer a high quality, two-component, epoxy-polyamide system that has exceptional adhesion to practically any surface including tanks, coastal installations, galvanized iron, pipelines, oluminum, steel, etc. Has excellent corrosion resistance and sealing properties. Highly alkali-resistant so there is no need for neutralization of new concrete. PRINCIPAL USES: As a primer for topcoats of Epoxy Enamel or Acquo Epoxy to be applied on metal, galvanized iron, wood and masonry. PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION PACKAGING

MIXING RATIO AVAILABLE COLORS:

20-25 sq.m./gallon / coat 2-3 hours Overnight 1.5 mildcoat Allow eight (8) hours before recoating. For best results, recoating should be done overnight. Boysen Epoxy Reducer #55 Paint brush or spray gun Boysen Epoxy Primer comes in 4-liter cans, % full packed with Boysen Curing Agent, 1-liter cans, full 3:1, paint to catalyst, respectively B-2200 Epoxy Primer White with curing agent #2202 8-2230 Epoxy Primer Gray with curing agent #2202 8-2260 Epoxy Primer Zinc Chromate Yellow with curing agent #2202 B-2270 Epoxy Primer Red Lead with curing agent #2202 8-2277 Epoxy Primer Red Oxide with curing agent #2202

SURFACE PREPARATION Concrete Flooring Remove oil and grease by detergent cleaning. For very smooth floors, acid etch smooth surfaces to improve adhesion. Do this by mixing one (1) part muriatic acid to one (1) part water. Apply over masonry and let stand for 2-3 minutes. Rinse with water. If available, rinse by pressure washing. Finished acid etched texture should be similar to that of 40-60 grit sandpaper. Make sure that the surfaces to be painted are clean and dry. Caution: Adequate protection and ventilation should be provided when working with acids Metal Wipe the surfoce with rag soaked in paint thinner to remove dust, dirt, grease, oil, wax and other foreign matter. For new G.I. sheets, etch the surfoce by applying 10% Boysen Metal Etching Solution #71 (dilute 1 part of 8-71 to 9 ports water).

87

Table of Contents

If repainting on surfaces with alkyd, latex or lacquer based coatings, scrape off all paint. Remove oil and grease by detergent cleaning followed by scuff sanding. To remove rust, wire brush or scrape affected areas and apply Boysen Metal Etching Solution #71. Let it stay for 10-15 minutes. Be sure to wash off surface thoroughly with water, letting it dry before applying paint. Primer should be applied immediately after treatment. PAINTING SCHEDULE

Concrete Flooring Mix three (3) parts of Boysen Epoxy Primer White # 2200 to one (1) part of its catalyst. Allow twenty (20) minutes induction time. Dilute 1:1 ratio with Boysen Epoxy Reducer #55. Apply as primer coating on bare concrete. Let dry overnight. Topcoat with 2-3 coats of Boysen Acqua Epoxy or Boysen Epoxy Enamel#2100. Let dry overnight before recoating. Let cure for 3 days before allowing foot traffic and 7 days for heavy duty use.

Metal Prime base metal with Boysen Epoxy Red Lead Primer #2270 or Boysen Epoxy Zinc Chromate Primer #2260. Let dry eight (8) hours before recoating. Topcoat with 2-3 coats of Boysen Acqua Epoxy or Boysen Epoxy Enamel#2100. Let dry overnight before recoating. NOTE: For epoxy-primed surfaces, topcoat should be applied not more than seven (7) days after priming to ensure good intercoat adhesion. Otherwise, re-priming is suggested.

Table of Contents

Boysen Epoxy Enamel DESCRIPTION: Boysen Epoxy Enamel is a high quality, two-component, epoxy-polyamide system that has excellent corrosion resistance and sealing properties. Highly alkali-resistant so there is no need for neutralization of new concrete. PRINCIPAL USES: As a topcoat for Boysen Epoxy Primer that can be applied on interior surfaces such as metal, galvanized iron, wood and masonry. PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION PACKAGING

MIXING RATIO

20-30 sq.m./gallon / coat 2-3 hours Overnight 1.5 mils/coat Allow eight (8) hours before recoating. For best results, recoating should be done overnight. Boysen Epoxy Reducer #55 Paint brush or spray gun Boysen Epoxy Enamel comes in 4-liter cans, 3/4 full packed with Boysen curing agent, 1-liter can, full 3: 1, paint to catalyst, respectively

AVAILABLE COLORS B2100 Boysen Epoxy Enamel White with Curing Agent #2101 B2132 Boysen Epoxy Enamel Silver Gray with Curing Agent #2103 821 44 Boysen Epoxy Enamel Royal Blue with Curing Agent #2103 B2151 Boysen Epoxy Enamel DarkGreen with Curing Agent #2103 821 72 Boysen Epoxy Enamel International Red with Curing Agent #2103 821 90 Boysen Epoxy Enamel Black with Curing Agent #2103

SURFACE PREPARATION Concrete Flooring Remove oil and grease by detergent cleaning. For smooth surfaces, acid etch to improve adhesion. Do this by mixing one (1) part muriatic acid to one (1) part water. Apply over masonry and let stand for 2-3 minutes. Rinse with water to remove residual acid. If possible, rinse by pressure washing. Finished acid etched texture should be similar to that of 40-60 grit sandpaper. Make sure that the surfaces to be painted are clean and dry. Caution: Adequate protection ond ventilation should be provided when working with ocids. Metal Wipe the surface with rag soaked in paint thinner to remove dust, dirt, grease, oil, wax and other 89

Table of Contents

foreign matter. For new G.I. sheets, etch the surface by applying 10% Boysen Metal Etching Solution #71 (dilute 1 part of B-71 to 9 parts water). If repainting on surfaces with alkyd, latex or lacquer-based coatings, scrape off all paint film to bare substrate. Remove oil and grease by detergent cleaning followed by scuff sanding. To remove rust, wire brush or scrape affected areas and apply Boysen Metal Etching Solution #71 over rusted portions. Let it stay for 10 - 15 minutes. Be sure to wash off surface thoroughly with water, letting it dry before applying paint. Primer should be applied immediately upon drying of the surface before rust sets in. PAINTING SCHEDULE Concrete Flooring Mix three (3) parts of Boysen Epoxy Primer White # 2200 to one (1) part of its catalyst. Allow twenty (20) minutes induction time. Thin 1:1 with Epoxy Reducer #55. Apply as primer coating on bare concrete floors. Let dry overnight. Mix Boysen Epoxy Enamel with its catalyst as with the procedure of the Boysen Epoxy Primer. Paint 2-3 coats of this mixture over well-primed surface. Allow 8 hours to overnight before recoating. Metal Prime base metal with Boysen Epoxy Red Lead Primer #2270 or Boysen Epoxy Zinc Chromate Primer #2260. Let dry 8 hours to overnight. Topcoat with 2-3 coats of Boysen Epoxy Enamel. Let dry overnight before recoating.

NOTE: Foot traffic abrasion resistance fully develops after three (3) days of curing. For heavy duty application, allow seven (7) days of drying. Application of topcoat should be done ideally within 7 days after priming to ensure good interat adhesion, otherwise re-application of primer is suggested.

Table of Contents

Boysen Acqua Epoxy DESCRIPTION: Boysen Acqua Epoxy is a two-component water based acrylic epoxy paint that has superior solvent, chemical and stain resistance ideal for concrete floors and properly primed metal surfaces. It has the advantage of easier application and better weather resistance properties. PRINCIPAL USES: For floorings, walls, metal substrates and other well primed surfaces. COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION PACKAGING MIXING RATIO

25-30 sq.m./gal./coat Thirty (30) minutes Four (4) hours 1.5 rnils/coat Allow four (4) hours before recoating. For best results, recoating should be done overnight. Not recommended paint brush, roller or airless spray gun Boysen Acqua Epoxy comes in 4-liter cans, 4/5 full and packed with Boysen Curing Agent, in 1-liter cans, 4/5 full 4: 1, paint to catalyst, respectively

AVAILABLE COLORS: 82900 White with #2910 Curing Agent 82930 Gray with #2910 Curing Agent 82950 Chrome Green with #2910 Curing Agent 82965 Medium Chrome Yellow with #2910 Curing Agent 82976 Ceramic Red with #2910 Curing Agent 82990 Black with #2910 Curing Agent SURFACE PREPARATION Concrete Flooring Remove oil and grease by detergent cleaning. For smooth surfaces, acid etch to improve adhesion. Do this by mixing one (1) port muriatic acid to one (1) part water. Apply over masonry and let stand for 2-3 minutes. Rinse with water to remove residual acid. If possible, rinse by pressure washing. Finished acid etched surface should have a texture similar to that of 40-60 grit sandpaper. Make sure that the surfaces to be painted are clean and dry. Caution: Adequate protection and ventilation should be provided when working with acids. Metal Wipe the surface with rag soaked in paint thinner to remove dust, dirt, grease, oil, wax and other foreign matter. For new G.I. sheets, etch the surface by applying 10% Boysen Metal Etching Solution #71 (dilute 1 part of 8-71 to 9 parts water).

If repainting on surfaces with alkyd, latex or lacquer-based coatings, scrape off all paint film to 91

Table of Contents

bare substrate. Remove oil and grease by detergent cleaning followed by scuff sanding. To remove rust, wire brush or scrape affected areas and apply Boysen Metal Etching Solution #71 over rusted portions. Let it stay for 10-15 minutes. Be sure to wash off surface thoroughly with water, letting it dry before applying paint. Primer should be applied immediately upon drying of the surface before rust sets in. PAINTING SCHEDULE

Concrete Flooring Mix three (3) parts of Boysen Epoxy Primer White # 2200 to one (1) part of its catalyst. Allow twenty (20) minutes induction time. Thin 1:1 with Epoxy Reducer #55. Apply as primer coating on bare concrete. Let dry overnight. Mix four (4) parts of Boysen Acqua Epoxy to one (1) part of its catalyst. Allow twenty (20) minutes induction time. Mixture may gel if not used within 24 hours. Apply three (3) coats as topcoat, allowing for at least 4 hours between coats. For best results, recoating should be done overnight.

Metal Prime base metal with Boysen Epoxy Red Lead Primer #2270 or Boysen Epoxy Zinc Chromate Primer #2260. Let dry eight (8) hours before recoating. Alternatively, Boysen Primeguard #4310 can be used. Apply a single coat and let dry for 2-4 hours before recoating. Finish with 2-3 coats of Boysen Acqua Epoxy. Let dry four (4) hours before recoating. NOTE: Foot traffic abrasion resistance fully develops after three (3) days of curing. For heavy-duty application, allow seven (7) days of drying.

Table of Contents

POLYURETHANE PA1NTS

Table of Contents

Boysen Poly-U 2K Paint DESCRIPTION: Boysen Poly-U 2K Paint is a two component urethane finish with excellent color and gloss stability, resistant to chemicals, waterproof and is a self-sanitizing coating. PRINCIPAL USES: Developed for quality painting of wood, concrete, fiber cement boards and metal surfaces where excellent gloss retention, abrasion and chemical resistance are desired. Recommended for industrial plants, wood works such as cabinets and shelves, counter tops, mouldings, windows, doors and door iambs, wooden accents and furnitures. Also for bathroom walls sanitary coating for laboratories and hospitals.

-

FEATURES AND BENEFITS

-

Excellent color and gloss retention the ability of Boysen Poly-U 2K to retain its vibrant color and high gloss level after prolonged exposure to weathering is unmatched by any other paint system.

-

Watertight It dries to a very hard film that serves as a watertight finish for outdoor areas as well as wet indoor areas such as bathrooms.

-

Maximum abrasion resistance It has exceptional abrasion resistance for a paint film, and is able to withstand repeated scratching, scrubbing and repeated detergent washing like no other brand. It is ideal for use in cabinets and shelves because of its ability to withstand constant opening and closing without cracking or peeling.

-

Excellent chemical resistance It is ideal for use in kitchen and laboratory counter tops because of its high resistance to stains, solvents and most chemicals. It is also a highly durable finish for industrial plants because of its strong resistance to chemical attacks, pollution and corrosive industrial environments. Self Sanitizing - It does not promote the growth of mildew and fungus. It is ideal for use in hospitals and laboratories in place of tiles that allow fungi to grow in its grouting. Superior dirt pick up resistance - Its hard film does not allow dirt to cling on, making it very easy to clean and allowing you to maintain a tile like finish for many years to come. PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION AVAILABILITY

20 - 25 sq.m./4 liters/coat Thirty (30)minutes Two (2) hours 1.5 mils/coat Allow eight (8)hours before recoat use Boysen Poly-U 2K Reducer only By brush or spray. Keep working area well ventilated at all times Available in Flat #1801, Semi-Gloss #I81 5, Classic Hi Gloss # 1810

Table of Contents

Note: Boysen Poly-U 2K may only be applied over epoxy, solvent-based acrylic or polyurethane systems. Do not apply over alkyd or lacquer-based films. If unsure, test or scrape old coating and follow new painting schedule.

PACKAGING

This product is a iwo-component system. 4-liter cans (Boysen Poly-U 2K base-7/8 full] 1-liter cans (Boysen Poly-U 2K Catalyst) 7:1, paint to catalyst, respectively

MIXING RATIO SURFACE PREPARATION

Allow new masonry to dry for 14 to 28 days under normal weather conditions before painting. Surface to be painted should be clean and dry, free from oil, greose, dust, dirt, contaminants and all loose grit and mortar. No need to treat new masonry with Boysen Masonry Neutralizer #44.

-

Wood Sutfaces should be sanded and dusted, clean and dry. MIXING Boysen Poly-U 2K comes in 2 components. The base is packed in 4-liter cans and is 7/8 full, while the catalyst is packed in a 1 liter can that is half full. Mix the iwo components and allow the mixture to stand for 20 minutes. Mixture may gel if not used within 5 hours. Note: Curing agent is moisture reactive. Keep container tightly sealed at all times. Caution: Uncured components are flammable. Keep away from sparks and open flames. PAINTING SCHEDULE Primer

Boysen Acrytex Primer # I 7 0 5 (wood or masonry walls) Boysen Epoxy Primer #2200 (flooring) Boysen Primeguard #4310 (metal)

puny

Boysen Acrytex Cast # I 7 1 1 (walls only)

Topcoat

Boysen Poly-U 2K (Flat, Semi-Gloss or Gloss)

NOTE: For epoxy primed surfaces, apply topcoat within 7 days after priming to ensure good intercoat adhesion.

Table of Contents

Boysen Poly-U Reducer #I805 DESCRIPTION: Boysen Poly-U Reducer #I805 is a fast evaporating solution consisting of ketones and acetates to improve application properties of Boysen Poly-U 2K Paint. PRINCIPAL USES: For thinninghedudion of Boysen Poly-U 2K Paint to improve paint flow and levelling when applied by brush or spray. Also used for clean-up of spills and point tools and equipment used. PACKAGING: 4-liter cans

Table of Contents

Hudson Polyurethane Floor Varnish Sealer DESCRIPTION: Hudson Polyurethane Floor Sealer is a two-component urethane finish for good adhesion of Hudson Polyurethane Floor Varnish Topcoat. PRINCIPAL USES: As a primer for parquet and other wooden floors for subsequent coating of Hudson Polyurethane Floor Varnish Topcoat (indoor use). PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL APPLICATION PACKAGING

MIXING RATIO

-

:

20 25 sq.m./4 liters/coat Thirty (30) minutes One (1) hour 1.5 mils/coat Recoat after 6 hours By brush or spray Hudson Polyurethane Floor Varnish Sealer 4 I't I er cans Hudson Polyurethane Catalyst 1/2-liter cans

-

-

Hudson Polyurethane Floor Sealer is mixed on a 7:l ratio by volume to its catalyst respediveiy. Enough paint is made only for four (4) hours work (maximum). Excess paint will gel.

PAINTING SCHEDULE New Wood 1st and 2nd coats 3rd to 5th

-

Hudson Polyurethane Floor Varnish Sealer Hudson Polyurethane Floor Varnish Topcoat

Table of Contents

Hudson Polyurethane Floor Varnish Topcoat DESCRIPTION: Hudson Polyurethane Floor Varnish Topcoat is a two-component urethane finish for wooden floors that cure to a tough, non-slip, mar resistant film. PRINCIPAL USES: Excellent parquet and other wooden floorings (indoor use). PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL APPLICATION THINNING PACKAGING

20 - 25 sq.rn./4 liters/coat Thirty (30) minutes One (1) hour 1.5 mils/coat Recoat after 2 hours By camel brush or spray Hudson Polyurethane Reducer Hudson Polyurethane Floor Varnish Topcoat - 4-liter cans Hudson Polyurethane Floor Varnish Catalyst 1-liter cans

-

SURFACE PREPARATION Surface to be painted should be clean and dry, free from dust, dirt and other foreign matter. Hammer all nails deep enough to apply wood filler. Sand rough wood until smooth, then dust off before painting. If repainting, first remove all blistering, peeling and scaling paint by wire brushing or Boysen Paint and Varnish Remover #141. Solvent wipe after treatment. MIXING Hudson Polyurethane Floor Sealer and Hudson Polyurethane Floor Varnish Topcoat are mixed on a 7:l ratio by volume to their catalyst. Enough paint is made only for four hours work (maximum). Excess paint will gel. PAINTING SCHEDULE New Wood - Apply 1 to 2 coats of Hudson Polyurethane Floor Varnish Sealer by brush or spray. Follow with 3 coats of Hudson Polyurethane Floor Varnish Topcoat applied by spray. Allow 7 days to fully cure before allowing heavy duty use and 3 days for foot traffic abrasion. Repainting

Old varnish film in bad condition should be stripped with Boysen Paint and Varnish Remover #141, sand then surface cleaned. Proceed as i n "New Wood." Old varnish film in good condition should be lightly sanded. Surface is cleaned before painting with topcoat. Allow 7 days to fully cure before allowing heavy duty use and 3 days for foot traffic abrasion.

Table of Contents

ALLIED PRODUCTS

Table of Contents

Boysen Masonry Neutralizer #44 DESCRIPTION: Boysen Masonry Neutralizer #44 is a liquid form product to be mixed with water to neutralize lime activity in new masonry surfaces. It is more effective than common zinc sulfate crystals. PRINCIPAL USES: For neutralization of lime activity in new concrete floorings, interior and exterior masonry walls. COVERAGE THINNING APPLICATION PACKAGING

20 sq.m./gallon of mixture water paint brush or roller 3.785 liter, 946.25 ml. and 473.12 ml. bottles

MIXING RATIO

1 part Boysen Masonry Neutralizer to 16 ports water

PAINTING SCHEDULE

1st step:

Remove oil and grease by detergent cleaning.

2nd step:

Apply diluted Boysen Masonry Neutralizer and let stand overnight

3rd step:

Rough sand surface to remove efflorescence salts

Caution: Adequate protection and ventilation should be provided when working with acids.

Table of Contents

Boysen Metal Etching Solution #71 DESCRIPTION: Boysen Metal Etching Solution #71 is an acid type metal cleaner and rust converter. It transforms rust and removes light deposits of mill oil. 8-71 destroys corrosion stimulators and properly conditions metal surfaces for painting. PRINCIPAL USES: As preparation agent for painting on new

and rusty metal surfaces

THINNING APPLICATION PACKAGING

25-30 sq.m./gallon of mixture depending on surface rustiness water paint brush 3.785 liter, 946.25 ml, and 473.12 ml. bottles

MIXING RATIO

1 part of Boysen Metal Etching Solution #71 to 9

PRACTICAL COVERAGE

parts water for new metal. Apply purely on rusts. PAINTING SCHEDULE

New Galvanized Metal Step 1: Wipe the surface with rag soaked in paint thinner to remove dust, dirt, grease, oil, wax and other foreign matter. Step 2: Apply 10% Boysen Metal Etching Solution #71 Rusty Metal Surface Step 1: Wire brush and scrape loose rust Step2:

Apply pure Boysen Metal Etching Solution #71 on rust.

Let solution stay for 10-15 minutes. Be sure to wash off surface thoroughly with water, letting it dry before applying paint. Primer should be applied immediately after treatment. Caution: Adequate protection and ventilation should be provided when working with acids.

Table of Contents

Boysen Paint and Varnish Remover # I 4 1 DESCRIPTION: Boysen Paint and Varnish Remover #I41 is an economical wax based paint stripper. PRINCIPAL USES: As preparation agent for repainting of metal, wood and masonry surfaces COVERAGE APPLICATION PACKAGING

20-25 sq.m./gallon of mixture depending on film thickness and adhesion paint brush. Use rubber gloves when applying 1-gallon and 1 -liter cans

PAINTING SCHEDULE Apply Baysen Paint and Varnish Remover #I41 on painted surface. When the old paint has wrinkled after approximately 10 minutes, scrape off with the use of spatula or putty knife. If the residue has become hard to remove, wash the surface with Boysen Lacquer Thinner and clean immediately.

Table of Contents

Boysen Masonry Surface Conditioner #304 DESCRIPTION: Boysen Masonry Surface Conditioner #304 is an alkyd-type, low viscosity paint for priming previously painted masonry surface where paint film is chalky. PRINCIPAL USES: As a primer when repainting chalky surfaces. PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS APPLICATION THINNING PACKAGING

25-30 sqm. / gallon /coat 5-6 hours 24 hours 1.25 mils/coat (approximately) by brush not necessary 4-liter cans

PAINTING SCHEDULE For chalking old paint, use Boysen Masonry Surface Conditioner #304 as primer. Follow with two coats of latex paint.

Table of Contents

Nation Wood Bleach 1 & 2 DESCRIPTION: Nation Wood Bleach 1 & 2 is a two solution preparation for a very natural wood finish, for removing stains, or for changing a previously stained surface to a lighter tone. PRACTICAL COVERAGE SURFACE DRY DRY THROUGH APPLICATION THINNING PACKAGING

25 sq. m. / gallon /coat 5-6hours 24 hours by brush not necessary 3.785 liter, 946.25ml. and 473.12 ml. bottles

PAINTING SCHEDULE: New wood surfaces: 1 st coat: Nation Wood Bleach 1 & 2 Apply first Nation Wood Bleach #1 for obout 10-15minutes, followed by Nation Wood Bleach #2 letting stay for also 10-15 minutes. For lighter color, repeat application of Nation Wood Bleach #2. Sponge off surface with water. Let dry then sand lightly,Allow 12 hours before applying stain or sealer. 2nd coat:

Boysen Oil Wood Stain (interior) or Boysen Xyladecor (exterior)

Final coat:

Boysen Varnishes

Repainting Old finish in bad condition should be stripped. Boysen Paint and Varnish Remover #I41 can be used to totally remove the finish. Make sure to clean and dry before coating as indicated for new wood. Solvent wipe stripper treated areas to remove residue.

Table of Contents

Boysen Spar Varnish #58 DESCRIPTION: Boysen Spar Varnish #58 is a clear, glossy varnish that dries to a hard durable film without obliterating the natural characteristics of wood. PRINCIPAL USES: Enhances wood grain of furniture, store fixtures, cabinets, doors, jambs and s. PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL APPLICATION THINNING

PACKAGING

25-30 sq. m. / gallon / coat

4-6 hours 12 hours 1.5 mils/coat Recoat after 12 hours by brush or spray Boysen Lacquer Thinner (Use Boysen Paint Thinner for better flow and leveling) 4-liter and 1 -liter cans

PAINTING SCHEDULE: New wood surfaces: 1 st coat: Boysen Oil Wood Stain Boysen Spar Varnish #58. Recoat for a clear gloss finish. Final coat:

Repainting Old finish in bad condition should be stripped. Boysen Paint and Varnish Remover # I 4 1 can be used to totally remove the finish. If old lacquer finish is in good condition, sand surface. Make sure to clean and dry before coating with Boysen Spar Varnish #58.

Table of Contents

Boysen Tinting Products Boysen Latex Colors DESCRIPTION: Boysen Latex Colors are concentrated acrylic based tinting paints for Boysen Permacoat Latex Paints. They disperse easily and produce tints from pastel to medium shades with even finishes. PACKAGING: 1-liter and l/4-liter cans NOTE: To produce dark shades, contad Boysen office. AVAILABLE COLORS B1405 Thalo Green 81407 Toluidine Red* 81409 Burnt Umber B1477 Venetian Red

B1404 Thalo Blue B1406 Raw Sienna 01408 Burnt Sienna B1466 Hansa Yellow* B1490 Lampblack

Boysen Oil Tinting Colors DESCRIPTION: Boysen Oil Tinting Colors are concentrated alkyd based tinting paints for oil, alkyd and enamel paints. They ore used to produce tints from pastel to medium shades, as well as with primers, sealers, and undercoats. PACKAGING: 1/4-liter cans NOTE: To produce dork shades, choose from factory mixed colors or intermix standard paint colors to get desired shade. AVAILABLE COLORS 82301 Chrome Green Medium B2303 Thalo Green B2304 Prussian Blue* B2306 Thalo Blue B2307 French Yellow Ochre 82309 Chrome Yellow Lemon* 8231 1 Burnt Umber

82313 Burnt Sienna B2314 Raw Sienna 82315 Bulletin Red* B2317 Venetian Red 82318 Lampblack 82319 Hansa Yellow*

*Interior use only

Table of Contents

Boysen Automotive Lacquer Tinting Colors* DESCRIPTION: Boysen Automotive Lacquer Tinting Colors are concentrated lacquer type tinting paints for lacquer based paints. They disperse easily and produce tints from pastel to medium shades with even finishes. PACKAGING: 1/4-liter and 1-liter cans

NOTE: To produce dark shades, choose from factory mixed colors or intermix two colors to get desired shade. AVAIIABILIN: B1304 Thalo Blue B1306 Yellow Ochre B131 6 Lemon Yellow B1376 Moly Orange

B1305 Thalo Green B1307 Toluidine Red B1317 Venetian Red B1391 Lamp Black

Boysen Acrytex Tinting Colors DESCRIPTION: Boysen Acrytex Tinting Colors are concentrated acrylic solvent based tinting colorants for Boysen Acryiex Products. They disperse easily and produce tints from pastel to medium shades with even finishes. PACKAGING: 1/4-liter cans NOTE: To produce dark shades, choose from factory mixed colors AVAILABLE COLORS B1304 Thalo Blue B1306 Yellow Ochre B l 3 l 6 Lemon Yellow B1376 Moly Orange

B1305 Thalo Green B1307 Toluidine Red B131 7 Venetian Red B l 3 9 l Lamp Black

*Interior use only

Table of Contents

Table of Contents